Heating, Ventilation, and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9781119628798
Author: Faye C. McQuiston; Jerald D. Parker; Jeffrey D. Spitler
Publisher: Wiley Global Education US
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 5.6P
Assuming that the blocks are not filled, compute the unit thermal resistance for the partition of problem 5-4.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Use FEM to calculate the temperature at nodes 2 and 3, as well as the heat at nodes 1 and 4 area.
please give the full solution,thank you
A pushrod in the valve mechanism of an automotive engine has a
nominal length of 203 mm. If the rod is made of SAE 4140 steel,
compute the elongation due to a temperature change from -20°C to
140°C.
TABLE3-4 Cocfficients of thermal expansion. a. for some
Problem 9-3: A T-type thermocouple is used to measure temperature difference
across insulation in the ceiling of a residence in an energy monitoring program. The
temperature difference across the insulation is used to calculate energy loss through
the ceiling from the relationship
Q = k Ac (AT)
where
Ac = ceiling area =
15 m²
k
=
insulation thermal conductivity
= 0.4
W
m°C
L
= insulation thickness = 0.25 m
AT = temperature difference = 5°C
Q
=
heat loss (W)
The value of the temperature difference is expected to be 5° C, and the thermocouple
emf is measured with an uncertainty of ±0.04 mV. Determine the required number of
thermopile junctions to yield an uncertainty in Q of ±5% (95%), assuming the
uncertainty in all variables other than AT may be neglected.
Chapter 5 Solutions
Heating, Ventilation, and Air Conditioning: Analysis and Design
Ch. 5 - Determine the thermal conductivity of 4 in. (100...Ch. 5 - Compute the unit conductance C for 512 in. (140...Ch. 5 - Compute the unit thermal resistance and the...Ch. 5 - What is the unit thermal resistance for an inside...Ch. 5 - Compute the thermal resistance per unit length for...Ch. 5 - Assuming that the blocks are not filled, compute...Ch. 5 - The partition of Problem 5-4 has still air on one...Ch. 5 - The pipe of Problem has water flowing inside with...Ch. 5 - Compute the overall thermal resistance of a wall...Ch. 5 - Compute the overall heat-transfer coefficient for...
Ch. 5 - Estimate what fraction of the heat transfer for a...Ch. 5 - Make a table similar to Table 5-4a showing...Ch. 5 - Estimate the unit thermal resistance for a...Ch. 5 - Refer to Problem 5-13, and estimate the unit...Ch. 5 - A ceiling space is formed by a large flat roof and...Ch. 5 - A wall is 20 ft (6.1 m) wide and 8 ft (2.4 m) high...Ch. 5 - Estimate the heat-transfer rate per square foot...Ch. 5 - A wall exactly like the one described in Table...Ch. 5 - Prob. 5.19PCh. 5 - Compute the overall heat-transfer coefficient for...Ch. 5 - Compute the overall heat transfer for a single...Ch. 5 - Determine the overall heattransfer coefficient for...Ch. 5 - A basement is 2020ft(66m) and 7 ft (2.13 m) below...Ch. 5 - Estimate the overall heat-transfer coefficient for...Ch. 5 - Rework Problem 5-23 assuming that the walls are...Ch. 5 - A heated building is built on a concrete slab with...Ch. 5 - A basement wall extends 6 ft (1.8 m) below grade...Ch. 5 - A 2440ft(7.312.2m) building has a full basement...Ch. 5 - The floor of the basement described in Problem...Ch. 5 - Assume that the ground temperature tg is 40 F (10...Ch. 5 - Use the temperatures given in Problem 5-30 and...Ch. 5 - A small office building is constructed with a...Ch. 5 - A 100 ft length of buried, uninsulated steel pipe...Ch. 5 - Estimate the heat loss from 100 m of buried...Ch. 5 - A large beverage cooler resembles a small building...Ch. 5 - Consider the wall section shown in Fig. 5-10. (a)...Ch. 5 - A building has floor plan dimensions of 3060ft....Ch. 5 - Compute the temperature of the metal roof deck of...Ch. 5 - Consider the wall section shown in Fig. -4a,...Ch. 5 - Consider the knee space shown in Fig. 5-11. The...Ch. 5 - Estimate the temperature in an unheated basement...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What types of polymers are most commonly blow molded?
DeGarmo's Materials and Processes in Manufacturing
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
Consider a subsonic compressible flow in cartesian coordinates where the velocity potential is given by (x,y)=V...
Fundamentals of Aerodynamics
A nozzle at A discharges water with an initial velocity of 36 ft/s at an angle with the horizontal. Determine ...
Vector Mechanics for Engineers: Dynamics
For the beam loading of Figure P334, draw the complete shearing force and bending moment diagrams, and determin...
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
Determine the length of the cantilevered beam so that the maximum bending stress in the beam is equivalent to t...
Mechanics of Materials (10th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- WORK PROBLEM 7-29 IF GLAZING SYSTEM IS 56. 7:27. FOR 3:00p.m. SOLAR TIME, ON JULY 21, IN BOISE, ID. A 3ft WIDE AND 5ft HIGH WINDOW FACES SOUTH WEST- (ACTUALLY, IT FACES SOUTHWEST ALL THE TIME!) THE NEW INOPERABLE WINDOW HAS A 2in. WIDE ALUMINUM FRAME WITH A THERMAL BREAK UTILIZING METAL SPACERS. THE GLAZING SYSTEM IS 21C IN TABLE 7-3. THERE IS NO INTERIOR OR EXTERIOR SHADING. CALCULATE THE TOTAL SOLAR HEAT GAIN, USING THE SIMPLIFIED APPROACH.arrow_forwardA short bar of copper, 25 mm in diameter, is enclosed centrally within a steel tube of external diameter 36 mm and thickness 3 mm. At 0°C the ends of the bar and tube are rigidly fastened together and the complete assembly heated to 80°C. Calculate the stress in the bar and in the tube if E for copper is 100 000 N/mm?, E for steel is 200 000 N/mm? and the coefficients of linear expansion of copper and steel are 0.000 01/°C and 0.000 006/°C, respectively.arrow_forward3. During the design of spherical pressure vessel for space programs, a primary criterion is the mass of the vessel (which determines how much it costs to put it into the orbit). Given the stress in a thin walled spherical vessel is tensile and given by: Pr 2t where P is the pressure in the vessel, r is the radius and t is the wall thickness. For safety, materials will experience stress smaller that yield stress by a safety factor N. 10-1 Show that the minimum mass of the pressure vessel will be m= 2Νπ Pr' where p is the density of material. ys Given the data in Appendix B1 and B4 in the textbook, select the material (from following table) that will result in the lightest possible pressure vessel. Note in brittle materials the yield strength equal to tensile stress. Material Steel 4340 Q&T Al 7075-T6 Ti-6-4, aged ZnO3+Y2O3 Nylon 6,6 Composite, Aramid fibers in ероху Composite: CFREarrow_forward
- I want to know how much heat the tube lost due to the material it is made of aluminum or steel. Even if it is a small difference in temperature. I want to know which material Conduct Heat the Best through this problem. material: Aluminum, steel ( the dimensions are the same for both) temperature touching cylinder: 65 Celcius temeprature inside cylinder 64.5 celsius room temperature 24 celcius Tube measurements outer radius r1 r1 = 4 in inner radius r2 r2 = 3 in outer circumference C1 C1 = 25.132741228718 in inner circumference C2 C2 = 18.849555921539 in height h = 8 in wall thickness t = 1 inarrow_forwardProblem Set – Temperature Change 1. A steel tire has a dimensions indicated in the figure below. At 78 degrees Celsius, the said tire was fit into a 1.8m to an engine wheel with 24 degrees Celsius. Calculate the contact pressure between the tire and the wheel after fitting together due to colling of 24 degrees Celsius. The coefficient of expansion due to temperature of the tire is 12.3 micrometer/ m- degrees Celsius and Modulus of Elasticity is EN GPa. | 12 mm | 200 mm 900mm wide steel tire- 12 mm Note: Neglect the deformation of the wheel due to the pressure of the tire Fn- 100arrow_forwardConsider the steel pressure vessel shown in Figure 1, intended to withstand an internalpressure of 40 MPa. The vessel has an outer diameter of 300 mm, an overall length of 500mm and a wall thickness of 30 mm. There is a 30 mm fillet radius where the interior wallsurface joins the end caps, as shown in the section view in Figure 1. The vessel is made ofASTM A27 steel. Use ANSYS Workbench to simulate this component and comment on itssuitability for production given the loading conditions detailed above.arrow_forward
- An eyed plate & pin is assembled as illustrated and are subjected to an opposing force of 10KN. The rod diameter & plate thickness is 6mm. The width of the plate is 20mm. A hole to which the pin is inserted is 8mm in diameter is located at the center of the plate. The plate is made of annealed SAE 1025 & the pin is high-heat oil quenched SAE 1095. (a) Determine if the assembly is safe to use; otherwise (b) Determine the safe load of the assembly.arrow_forwardA circular cross-sectional rod made of AISI Type 303 Stainless Steel is normally operated at126oF. Length and radius of the rod are 1.5 ft and 1.75 in., respectively. What would be thechange in length of the rod, if it is subjected to a temperature of 214oF? Coefficient of thermal expansion of the rods’ material is 9.6 × 10^-6 in./in. Degrees Fahrenheit.arrow_forward4. To make a secure fit , rivets that are larger than the rivet hole are often used and the rivet is cooled (usually in dry ice) before it is placed in the hole. A steel rivet 1.871cm in diameter is to be placed in a hole 1.869cm in diameter at 20°C. To what temperature must the rivet be cooled if it is to fit in the hole?arrow_forward
- please answer problem 5-6arrow_forwardQ4/ A room on the second floor of a house with a balcony has a door. The door made of teak (wood) and it contains a large sheet of glass (outside winter type) in the middle and constitutes 80% of the area of the door. Door thickness is 40 mm and the temperature in the room 25. °C when the temperature is in the balcony 8 °C. Calculate the rate of heat loss from the room to the balcony through the door. The door dimensions 2m x 1m. Assume Inside and outside still air thermal resistance f= 8.29 W/m2 °C and f. 34.1 W/m2 °C respectivelyarrow_forward6- One way of measuring the thermal conductivity of a material is to sandwich an electric thermofoil heater between two identical rectangular samples of the material and to heavily insulate the four outer edges, as shown in the figure. Thermocouples attached to the inner and outer surfaces of the samples record the temperatures. During an experiment, two 0.5-cm-thick samples 10 cm x 10 cm in size are used. When steady operation is reached, the heater is observed to draw 35Wof electric power, and the temperature of each sample is observed to drop from 82°C at the inner surface to 74°C at the outer surface. Determine the thermal conductivity of the material at the average temperature. Aarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license