Use the statement “Connect two bodies of water with no gradient.” Develop a series of questions to better understand the need.
The series of questions to better understand the need using the statement, “Connect two bodies of water with no gradient”.
Explanation of Solution
A need is an indefinite wishes that expresses what the customers would like a product to do for them whereas the requirements are the designer’s detailed breakdown of what the product should do and achieved based on the customers’ statements.
Why to connect two bodies of water with no gradient?
What material should be used to connect two bodies of water with no gradient?
From where to connect two bodies of water with no gradient?
When to connect two bodies of water with no gradient?
How to connect two bodies of water with no gradient?
Thus, the above are the series of questions to better understand the need using the statement, “Connect two bodies of water with no gradient”.
Want to see more full solutions like this?
Chapter 5 Solutions
ENGINEERING DESIGN PROCESS
- Solve the problem, take a clear picture of your solution and submit it next meeting. 1. If the pressure at a point in the ocean is 60 kPa, what is the pressure 27 meters below this point? Specific gravity of seawater is 1.03.arrow_forwardA ship arrives at the mouth of a river in water of density 1016 kg per cu. m with a freeboard of ‘S’ m. She then discharges 150 tonnes of cargo, and proceeds up river to a second port, consuming 14 tonnes of bunkers. When she arrives at the second port the freeboard is again ‘S’ m, the density of the water being 1004 kg per cu. m. Find the ship’s displacement on arrival at the second port. Kindly ahow the step by step solution and careful with the units. Thank you!!!arrow_forwardThe Renault Kaper is a popular brand of car in Republica. It has a fuel capacity (tank size) of 28 liters. It has afuel efficiency of (f)___15.2_____ kilometers per liter. With a full tank of fuel, could a Renault Kaper travel the (g)___471______ kilometer distance between Capital City and Costa Bay without needing to refill the tank? Show all supporting calculations. Write an explanation of your conclusion in complete sentences.arrow_forward
- ( computational fluid dynamics question) Question:  If the calculations lag behind the flow of fluid, what factor of the simulation gets affected? Circle Final answer or State it clearlyarrow_forwardShow a written solution of the problemarrow_forwardsolve, show assumptions and full solutionsarrow_forward
- In general term, ______________ is the tendency of one fluid to spread on to a solid surface in the presence of other fluid a. Relative Density b. Porosity c. Permeability d. Viscosity e. Wettabiltyarrow_forwardIf a pool is irregularly shaped and a person being assessed has a weight mg= 800 N but weighs Fn= 40N while submerged. Assuming a residual volume Vres= 1.4 L= 0.0014 m^3. a. What is their average density b. What percentage of their body volume would be above water, while floating? c. What is their bodys volume d. How much more buoyant force would they experience with their lungs holding a full six liters? What percentage of thheir body volume would be above water now?arrow_forwardA circular section of lawn on a golf course needs to be watered with 2 inches of water per week. If the circle is 100 feet in diameter, how many gallons of water per week are needed?arrow_forward
- solve both, show all steps, assumptions, comments, and solutionsarrow_forward7.) Water flowing in an open channel at a depth of 2 m and a velocity of 3 m/s. If flows down a chute into another channel where the depth is 1 m and the velocity is 10 m/s. Neglecting friction, determine the difference in elevation of the channel floors. Answer: 3.64 M Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flowarrow_forwardPlease read the project 2 description, then write down the solution strategy answer should be 100 words only The project 2 descriptions is shown as follows: There are three tanks as shown in Figure 1. Tank T1 initially contains 40 gals of water in which 16.98 lb of salt is dissolved. Tank T2 initially contains 40 gals of water and 3.92 lb of salt. Tank T3 initially contains 40 gals of water and 7.13 lb of salt. The inflow into T1 is 2 gal/min pure water from the outside and 2 gal/min brine from T2. The outflow from T1 to T2 is 4 gal/min.The inflow into T2 is 4 gal/min from T1 and 2 gal/min from T3. The outflow from T2 to T1 is 2 gal/min and from T2 to T3 is 4 gal/min. The inflow into T3 is 4 gal/min from T2. The outflow from T3 to T2 is 2 gal/min and from T3 to outside is 2 gal/min, as shown in the figure. The mixtures are kept uniform by stirring. Find and plot the salt contents y1(t), y2(t), and y3(t) in T1, T2, and T3, respectivelyarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY