Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 54, Problem 5ASRQ
While discussing solar sensors: Technician A says that a solar sensor is a photo diode that receives a 5-volt reference signal from the control module. Technician B says that when the intensity of sunlight increases, the output voltage increases, and as the sunlight decreases, the output voltage decreases. Who is correct?
- Technician A only
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says that some types of voltage sensors provide input to the computer by modifying or controlling a constant, predetermined voltage signal. Technician B says that a coolant temperature sensor is a voltage-generating sensor. Who is correct?
Which of the following will be used by a contact type sensor ?
a.
Ultrasonic Sound Wave
b.
Dial Gauge
c.
Magnetic field
d.
Laser Beam
Describe at least two methods of checking the operation of Hall effect sensors?
Chapter 54 Solutions
Automotive Technology
Ch. 54 - What is the amount of heat necessary to change the...Ch. 54 - Explain how an electromagnetic compressor clutch...Ch. 54 - Describe four ways in which the heater control...Ch. 54 - What is the purpose of the compressor clutch...Ch. 54 - What does change of state mean? And why is it...Ch. 54 - What state is the refrigerant in when it leaves...Ch. 54 - What causes condensed water to leak from the air...Ch. 54 - Explain why a diode may be wired into the compres...Ch. 54 - On which of the following laws of nature is the...Ch. 54 - Which of the following statements is true?...
Ch. 54 - Which of the following statements is false? The...Ch. 54 - Which of the following statements about PTC...Ch. 54 - Which of the following is electrically connected...Ch. 54 - Which of the following oils is used in an original...Ch. 54 - A heating system includes all of the following...Ch. 54 - Technician A says that a great amount of heat is...Ch. 54 - Technician A says that suction lines become very...Ch. 54 - While discussing the reasons the use of R-134a is...Ch. 54 - While discussing the reaction by a refrigerant to...Ch. 54 - While discussing solar sensors: Technician A says...Ch. 54 - While discussing the future use of CO2 as a...Ch. 54 - Technician A says that when the A7C system is off,...Ch. 54 - Technician A says that when the refrigerant is...Ch. 54 - A heater does not supply enough heat and the...Ch. 54 - While discussing relative humidity: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that based on current conditions, a reference voltage sensor modifies a fixed voltage from the computer and sends that voltage back to the computer. Technician B says that most reference voltage sensors are variable resistors or potentiometers. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following statements about zirconium oxygen sensors is not true? The normal operating range for an O2S is between 0 and 1 volt. If the sensors voltage toggles between 0 volts and 500 millivolts, it is operating normally. The voltage signal from an upstream O2S should have seven cross counts within 5 seconds with the engine running without a load at 2,500 rpm. Engine control systems monitor the activity of the O2S and store a code when the sensors output is not within the desired range.arrow_forwardWhile diagnosing an electronic control system: Technician A turns the ignition off before disconnecting a connector or component. Technician B uses a jumper wire to bypass a potentially faulty sensor and then observes the scan tool. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Which of the following is not a voltage-generating type sensor? vehicle speed sensor OSS MAP ISSarrow_forward3- Contact Type displacement sensors makes direct contact with the object being monitored. Select one: True Falsearrow_forwardA TPMS sensor is being replaced. Technician A says that if you replace it with a manufacturer specific TPMS, you need to program the sensor before install. Technician B says that all manufacture specific TPMS sensors use a 315 MHz radio frequency. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forward
- When an engine is running lean, the voltage signal from the oxygen sensor will be (low or high).arrow_forwardWhile discussing Hall-effect vehicle speed sensor tests: Technician A says to use an ohmmeter to test the resistance of the coil. Technician B says that the voltage generated by the sensor can be measured by connecting a voltmeter across the sensors terminals. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhen testing an engine temperature sensor: Technician A uses an ohmmeter to test the thermistor. Technician B says that the thermistor reacts to pressure and applies air pressure to the backside of the sensor. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing TP sensor diagnosis: Technician A says that a four-wire TP sensor contains an idle switch. Technician B says that in some applications, the TP sensor mounting bolts may be loosened and the TP sensor housing rotated to adjust the voltage signal with the throttle in the idle position. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following is not a true statement about lamp-out warning lights? The lamp-out warning module measures small changes in voltage levels. An electronic switch in the module completes a ground path for the indicator lights in the event of a bulb going out. A special resistance wire is used in multibulb systems. When a bulb burns out. the module senses the increased voltage drop and turns on the indicator lamp.arrow_forwardTechnician A says that EMI can affect sensor signals. Technician B says that EMI can cause intermittent driveability problems. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Thermal Radiation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=FDmYCI_xYlA;License: Standard youtube license