PROGRAMMABLE LOGIC CONTROLLERS W/CONNEC
2017th Edition
ISBN: 9781264228720
Author: Petruzella
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Question
thumb_up100%
Chapter 6, Problem 1P
Program Plan Intro
NC pushbutton switch:
- The abbreviation NC stands for a Normally Closed pushbutton switch.
- It will be initially at closed contact and will be opened when the switch or coil is energized.
- It opens a circuit when it is pressed and return back to its closed condition when it is released.
- An electrical symbol used to represent NC pushbutton switch is given below
Given:
The conventional hardwired relay circuit should perform the following circuit functions when a NC pushbutton is pressed.
- The pilot light must be switched ON.
- The solenoid must be de-energized.
- Motor running should be started.
- Sound a horn.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Show a simple interface from an output port to drive an LED. Assume that the output port can sink or source up to 20 milliamps and the forward voltage of the LED is 2 volts. Show your calculations
Design an appropriate combinational circuit that implements a digital system with the following output functions an AC remote: ON, OFF, MODE, SHIFT, FAN, SMART, SWING, ECO using a decoder.
Using the sim8085 write the following code:
In a sensor network, three pressure sensors are connected which gives the reading of 4 psi, 8 psi and 10 psi. All the sensor readings are to be summed up and store as a single reading
Chapter 6 Solutions
PROGRAMMABLE LOGIC CONTROLLERS W/CONNEC
Ch. 6 - Prob. 1RQCh. 6 - Prob. 2RQCh. 6 - Prob. 3RQCh. 6 - Prob. 4RQCh. 6 - Prob. 5RQCh. 6 - Prob. 6RQCh. 6 - Prob. 7RQCh. 6 - Prob. 8RQCh. 6 - What do the abbreviations NO and NC represent when...Ch. 6 - Prob. 10RQ
Ch. 6 - Prob. 11RQCh. 6 - Prob. 12RQCh. 6 - Compare the operation of a photovoltaic solar cell...Ch. 6 - What are the two basic components of a...Ch. 6 - Prob. 15RQCh. 6 - Give an explanation of how a scanner and a decoder...Ch. 6 - Prob. 17RQCh. 6 - Prob. 18RQCh. 6 - Prob. 19RQCh. 6 - Prob. 20RQCh. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Prob. 23RQCh. 6 - Prob. 24RQCh. 6 - Prob. 25RQCh. 6 - Prob. 26RQCh. 6 - Prob. 27RQCh. 6 - Prob. 28RQCh. 6 - Prob. 29RQCh. 6 - Prob. 30RQCh. 6 - Prob. 31RQCh. 6 - Prob. 32RQCh. 6 - Prob. 33RQCh. 6 - Prob. 1PCh. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Design a PLC program and prepare a typical I/O...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8P
Knowledge Booster
Similar questions
- draw a qpsk complete modulator circuit using circuit components of various types not a block diagram.arrow_forwardGiven the following Combinational circuit, Use Verilog HDL on Quartus tool to1. Write a Verilog HDL code to describe the module DCDR2×4 // this module name must be your last name ( younis2. Write a Verilog HDL code to describe the whole system structurally from its subsystems// this module name must be your university number ( 1181230)arrow_forwardHow are the components interralated with each other on this circuitarrow_forward
- Build a full adder circuit. What does this circuit do? Is it parallel or serial?arrow_forwarddraw a QPSK demodulator circuit using different circuit components. stop rejecting questionsarrow_forwardDesign the interface for a positive logic switch to TM4C123GXL Port A pin 7. Show formulas and calculations for each circuit element. Draw the circuit schematics with components labelled with their names and values. Write the C code as a function to initialize the port for interfacing the switch. Write a function to read the data value of Port A pin 7. Comment your code to explain each initialization step clearly.arrow_forward
- Comment on the following line: "Using a 7219 you can drive 64 LEDs while you only need 3 wires to interface it to a microcontroller"arrow_forwardIn the context of digital circuits, what is feedback?arrow_forwardIn a circuit design to be made using the 89C52 microcontroller, if a PWM signal is produced and DC motor speed control is desired, which module will definitely be used in the microcontroller? a) I / O b) ADC c) PWM d) Serial communication e) DACarrow_forward
- Cna you draw the circuit in a paper a better one to understand?arrow_forwardBuild a half adder circuit. What does this circuit do? Is it parallel or serial?arrow_forward1. Design and implement a circuit using positive edge triggered DFFs that generates a pulse (p = 1) on the 2nd, 3rd, 5th, and 7th clock cycles after initialization. The sequence should repeat every 8 clock pulses. Include an asynchronous reset signal. 1.1 Implement your design in Verilog (behavioral)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning