A 0.505-in.-diameter aluminum alloy test bar is subjected to a load of 25,000 lb. If the diameter of the bar is 0.490 in. at this load, determine (a) the engineering stress and strain and (b) the true stress and strain.
a)
Engineering stress and strain has to be determined
Answer to Problem 50AAP
The magnitude of engineering stress is 125,000 psi.
The magnitude of engineering strain is 0.060.
Explanation of Solution
Write the expression for initial area of the bar:
Here, initial diameter of the bar is
Write the expression for initial area of the bar:
Here, final diameter of the bar is
The volume of the bar before and after deformation is same.
Write the expression for the engineering stress as given as follows.
Here, applied force is
Write the expression for the engineering strain as given as follows.
Substitute equation (III) in equation (V).
Conclusion:
Substitute
Substitute
Substitute
Thus, the magnitude of engineering stress is 125,000 psi.
Substitute
Thus, the magnitude of engineering strain is 0.060.
b)
true stress and strain has to be determined
Answer to Problem 50AAP
The magnitude of true stress is 132,555.67 psi.
The magnitude of true strain is 0.0587.
Explanation of Solution
Write the expression for the true stress as given as follows:
Write the expression for the true strain as given as follows:
Conclusion:
Substitute
Thus, the magnitude of true stress is 132,555.67 psi.
Substitute
Thus, the magnitude of true strain is 0.0587.
Want to see more full solutions like this?
Chapter 6 Solutions
Foundations of Materials Science and Engineering
Additional Engineering Textbook Solutions
Vector Mechanics for Engineers: Dynamics
Thermodynamics: An Engineering Approach
Applied Statics and Strength of Materials (6th Edition)
Vector Mechanics for Engineers: Statics and Dynamics
Degarmo's Materials And Processes In Manufacturing
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
- A cylindrical specimen of brass that has a diameter of 21 mm, a tensile modulus of 122 GPa, and a Poisson’s ratio of 0.37 is pulled in tension with force of 38704 N. If the deformation is totally elastic, what is the strain experienced by the specimen?arrow_forwardExplain the different experimental methods that would relate stress with strain to determine the stress-strain diagram for a specific material.arrow_forwardHow are Engineering stress and strain calculated?arrow_forward
- Is the engineering stress-strain curve or the true stress-strain curve preferred for large strains? Explain.arrow_forwardTensile test under 40,000 N load was applied to a low carbon steel with a sample diameter of 6 mm. As the diameter of the specimen under load decreases to 5 mm, calculate a) Engineering stress and% elongation values, b) Actual stress and% elongation values.arrow_forwardCan a three-dimensional material change into a plane strain state or plane stress state when plastic deformation/destruction occurs under uniaxial tensile stress? If it can, give an example and explain.arrow_forward
- Differentiate between normal strain measures and sheer strain measures?arrow_forwardIn a typical engineering stress-strain diagram, stress keeps on increasing after yield point due to strain hardening. In a few words or in a single short sentence explain what causes strain hardening?arrow_forwardA material has a strength coefficient of 150,000 psi. At the onset of plastic deformation, the material had an 18 percent increase over its initial length, and at the beginning of non-uniform deformation, the material experienced an engineering strain of 0.58. Calculate the engineering and true strains at yield. Also, calculate the engineering and true strains at the point where a maximum engineering stress is experienced by the material. Determine the strain-hardening index. Calculate the ultimate tensile strength. Calculate the modulus of elasticity. Given: K = 150,000 psi 18% increase in length ey = 0.58 Want: ey =? eu =? n =? UTS =? E =? εy =? εu =?arrow_forward
- During stress-strain test, the unit deformation at a stress of 35 MPa was observed to be 167 x 10^-6 m/m and at a stress of 140 MPa it was 667 x 10^-6. If the proportional limit was 200 MPa, what is the modulus of Elasticity (GPa)? What is the strain corresponding to a stress of 80 MPa?arrow_forwardWhat type of behaviour is observed from these stress-strain curves?arrow_forwardin tensile test data, show step by step how to find stress and strain in aluminiumarrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY