SHIGLEY'S MECH.ENGINEERING DESIGN-EBK>I
10th Edition
ISBN: 9781259489563
Author: BUDYNAS
Publisher: INTER MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 36P
A guide pin is required to align the assembly of a two-part fixture. The nominal size of the pin is 15 mm. Make the dimensional decisions for a 15-mm basic size locational clearance fit.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A medium drive of a steel hub of a gear with an outside diameter of 80 mm on a steel shaft
is required.
a) Make the dimensional decisions for a 49-mm basic size with a medium drive fit for the
hub and shaft, and specify dimensions with tolerances for the shaft and the hub bore for
the fit.
b) When the interference pressure "p" is at a minimum (p at Smin) for the specified tolerances
how much torque (in Nm) can be transferred with the medium drive fitted assembly if the
steel to steel friction is 0,8 and the hub of the length is 170 mm. E=207 GPa
Problem (10): The following limits are specified in a limit system, to give a clearance fit between a hole and a shaft: Hole = 10 (+0.05 )/(-0.00 ) mm and Shaft = 10 (-0.003)/(-0.010) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.
second slide is data for the problem in slide 1
Chapter 7 Solutions
SHIGLEY'S MECH.ENGINEERING DESIGN-EBK>I
Ch. 7 - A shaft is loaded in bending and torsion such that...Ch. 7 - The section of shaft shown in the figure is to be...Ch. 7 - The rotating solid steel shaft is simply supported...Ch. 7 - A geared industrial roll shown in the figure is...Ch. 7 - Design a shaft for the situation of the industrial...Ch. 7 - The figure shows a proposed design for the...Ch. 7 - For the problem specified in the table, build upon...Ch. 7 - Prob. 8PCh. 7 - For the problem specified in the table, build upon...Ch. 7 - For the problem specified in the table, build upon...
Ch. 7 - In the figure is a proposed shaft design to be...Ch. 7 - The shaft shown in the figure is proposed for the...Ch. 7 - Prob. 20PCh. 7 - The shaft shown in the figure is proposed for the...Ch. 7 - Prob. 25PCh. 7 - Prob. 26PCh. 7 - Prob. 27PCh. 7 - A 25-mm-diameter uniform steel shaft is 600 mm...Ch. 7 - Prob. 29PCh. 7 - Compare Eq. (727) for the angular frequency of a...Ch. 7 - Prob. 31PCh. 7 - The steel shaft shown in the figure carries a...Ch. 7 - A transverse drilled and reamed hole can be used...Ch. 7 - Prob. 34PCh. 7 - The shaft shown in Prob. 721 is proposed for the...Ch. 7 - A guide pin is required to align the assembly of a...Ch. 7 - Prob. 37PCh. 7 - Prob. 38PCh. 7 - Prob. 39PCh. 7 - A ball bearing has been selected with the bore...Ch. 7 - Prob. 41PCh. 7 - A gear and shaft with nominal diameter of 35 mm...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Q-3 Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a = 40.500 0.025 mm b = 52.000 0.075 mm c = 73.000 0.015 mm d = 165.900 0.250 mm Parts A, B, and C are standard parts supplied by vendors from the market, but we are to machine part D according to the the width that you are asked to specify. (a) Determine the mean gap w0 of w and its tolerance. (b) Determine the mean size of d (d0) that will assure that w ≥ 0.050 mm.arrow_forwardPlease refer to the image attached. Study the sheet metal assembly at the top of the image. It consists of two main parts, a flexible tube and reinforcement cap. They are attached with 4 self threading fasteners. Select datum features based on the mating condition. Make sure to note the fit between the parts. Calculate and apply position tolerances using the fastener formulas on the previous pages. Apply other necessary geometric tolerances to ensure assembly and minimize mismatch on outside edges.arrow_forwardProblem (9): In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 70 (+0.04 )/(+0.00 ) mm and Shaft = 70 (-0.04)/(-0.08) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.arrow_forward
- A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1) with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing inlet diameter as the basic size. Oudet Bearing Inlet Journal Figure 1 AJournal Bearingarrow_forwardComplete feature control frame that controls perpendicularity of the hole to .012" diameter at MMC relative to datum feature A and straightness of the hole to .004" diameter at MMCarrow_forwardIn a limit system, the following limits are specified for a hole and shaft assembly: Hole = 30 (+0.02 )/(+0.00 ) mm and Shaft = 30 (-0.02)/(-0.05) mm. Determine the basic size, tolerance and allowance, maximum and minimum clearances, type of fit.arrow_forward
- Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary dimensions as basic. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.arrow_forwardThe 1/2-inch diameter pin in the drawing below is required to be perpendicular to datum feature A within a tolerance of .002 at MMC. Provide the appropriate feature control frame specifying this requirement. A. B. C. D. O O O D B A C A ==== .002 MA === .002 AM 0.002 MA .002 AM || ==== ==== Ø.498-.500 T ||| || || ||arrow_forwardComplete the hole specification including a position tolerance of .018" diameter at MMC relative to primary datum feature A, secondary datum feature B, and tertiary datum feature C.arrow_forward
- Show the steps and calculations to determine one type of fit. Diameter of ball bearing hole is = 19.945mmarrow_forwardSolve show all steps/solution as wellarrow_forwardCalculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When calculating the limit tolerances for features that mate with purchased parts, the purchased part size must be known. This may be obtained be requesting a drawing from a vendor or, a caliper or micrometer can be used to obtain an accurate size. A shaft diameter of 1.2500" is to be pressed into a part using a FN3 interference (force) fit. Limits of size for the shaft diameter are 1.2500" and 1.2495". Determine the Limits of the hole diameter. Show all work.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License