SYSTEM DYNAMICS LL+CONNECT
3rd Edition
ISBN: 9781264201891
Author: Palm
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 7, Problem 7.48P
A particular house wall consists of three layers and has a surface area of 30 m2. The inside layer is 10 mm thick and made of plaster board with a thermal conductivity of k = 0.2 W/(m • °C). The middle layer is made of fiberglass insulation with k = 0.04 W/(m • °C). The outside layer is 20 mm thick and made of wood siding with k = 0.1 W/(m • °C). The inside temperature is 20°C, and the convection coefficient for the inside wall surface is /i, = 40 W/(m~ • °C). The convection coefficient for the outside wall surface is ho= 70 W/(m~ • °C). How thick must the insulation layer be so that the heat loss is no greater than 400 W if the outside temperature is —20°C?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A steel pipe (outside diameter 100 mm) is covered with two
layers of insulation. The inside layer, 40 mm thick, has a
thermal conductivity of 0.07 W/(m K). The outside layer,
20 mm thick, has a thermal conductivity of 0.15 W/(m K).
The pipe is used to convey steam at a pressure of 600 kPa. The
outside temperature of insulation is 24°C. If the pipe is 10 m
long, determine the following, assuming the resistance to
conductive heat transfer in steel pipe and convective resistance
on the steam side are negligible:
a. The heat loss per hour.
b. The interface temperature of insulation.
A wood stove heats a small cabin with the following dimensions 8 m x 6 m x 3 m (length x width x height) to 25°C. Of the heat generated by burning wood, 60% is lost up the chimney. The cabin also loses heat through walls, ceiling and floor. Assume that all sides of the house except the floor are insulated with a 10 cm thick polyethylene foam layer having a thermal conductivity htc = 0.038 W/(m•°C). The heat loss through the floor is 1/5 of the heat loss through the ceiling. Outside air is at -5°C. a) How much heat is lost in total from the ceiling, walls, and floor? b) How many kg of wood per hour is needed as fuel for the cabin to maintain its temperature if heat value of wood is AH = 18,000 kJ/kg?
Water vapor at a temperature of 120 ° C flows through a stainless steel pipe (k = 57 W / mK). The inner diameter of the pipe is 47 mm, the outer diameter is 50 mm, and the length is 100 m. The heat transfer coefficient between the water vapor and the pipe wall is 200 W / m²K, and the heat transfer coefficient between the outer surface of the pipe and the ambient air is 25 W / m_K. The outdoor air temperature is 10 ° C. Find the thermal conductivity coefficient of the insulation material, since it is desired to insulate with an insulation material with a layer thickness of 50 mm in order to reduce the loss of heat from the pipe by 60%.
Chapter 7 Solutions
SYSTEM DYNAMICS LL+CONNECT
Ch. 7 - Prob. 7.1PCh. 7 - Refer to the water storage and supply system shown...Ch. 7 - Prob. 7.3PCh. 7 - In Figure P7.4 the piston of area A is connected...Ch. 7 - Refer to Figure 7.1.4a. and suppose that p\ — p2=...Ch. 7 - Pure water flows into a mixing tank of volume V =...Ch. 7 - Consider the mixing tank treated in Problem 7.6....Ch. 7 - Derive the expression for the fluid capacitance of...Ch. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - 7.11 Derive the expression for the capacitance of...Ch. 7 - Air flows in a certain cylindrical pipe 1 m long...Ch. 7 - Derive the expression for the linearized...Ch. 7 - Consider the cylindrical container treated in...Ch. 7 - A certain tank has a bottom area A = 20 m2. The...Ch. 7 - A certain tank has a circular bottom area A = 20...Ch. 7 - The water inflow rate to a certain tank was kept...Ch. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - In the liquid level system shown in Figure P7.20,...Ch. 7 - The water height in a certain tank was measured at...Ch. 7 - Derive the model for the system shown in Figure...Ch. 7 - (a) Develop a model of the two liquid heights in...Ch. 7 - Prob. 7.24PCh. 7 - Design a piston-type damper using an oil with a...Ch. 7 - Prob. 7.26PCh. 7 - 7.27 An electric motor is sometimes used to move...Ch. 7 - Prob. 7.28PCh. 7 - Prob. 7.29PCh. 7 - Figure P7.3O shows an example of a hydraulic...Ch. 7 - Prob. 7.31PCh. 7 - Prob. 7.32PCh. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - (a) Determine the capacitance of a spherical tank...Ch. 7 - Obtain the dynamic model of the liquid height It...Ch. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Prob. 7.42PCh. 7 - Prob. 7.43PCh. 7 - Prob. 7.44PCh. 7 - Prob. 7.45PCh. 7 - The copper shaft shown in Figure P7.46 consists of...Ch. 7 - A certain radiator wall is made of copper with a...Ch. 7 - A particular house wall consists of three layers...Ch. 7 - A certain wall section is composed of a 12 in. by...Ch. 7 - Prob. 7.50PCh. 7 - Prob. 7.51PCh. 7 - A steel tank filled with water has a volume of...Ch. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An exterior wall of a house may be approximated by a 4-in layer of common brick [k =0.7 W/m · ◦C] followed by a 1.5-in layer of gypsum plaster [k = 0.48 W/m · ◦C]. What thickness of loosely packed rock-wool insulation [k = 0.065 W/m · ◦C] should be added to reduce the heat loss (or gain) through the wall by 80 percent?arrow_forwardYou have mounted 100W PCBs as vertical fins. The fins are 60mm deep x 60mm high x 1mm thick and made of G10 (k = 5W/mK). The fins are spaced 6mm apart (pitch = 7mm). (Air temperature = 40oC, B = 0.017) Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), TInfinity = 25oC a) What is the Rayleigh number? b) What is the Nusselt number? c) What is the convection coefficient?arrow_forwardSome sections of the Alaska pipeline above ground are supported by vertical steel supports (k = 25 W/mK), which have a length of 1 m and a cross-sectional area of 0.05 m². Under normal operating conditions, the temperature variation along the length of the steel support is given by the expression T = 100 – 150x + 10x², where T and x have units of °C and m, respectively. Temperature variations in the cross-sectional area of the support are negligible. Evaluate the temperature and the heat conduction rate at the pipeline-support junction (x = 0) and at the support-soil interface (x = 1 m). Explain the difference in heat rates.arrow_forward
- Find the minimum amount of diameter for the insulation of a spherical water tank? Radius of the tank is 10 m, thermal conductivity is 25 W/(m^2*K) and convective coefficient is 5 W/(m*K)arrow_forwardR Value: Wall: 0.961m2k/w Floor: 0.676m2k/w Roof: 0.7465m2k/w In a table format show with calculations and research how much money you can save by installing a 115mm layer of insulation (R2.9) in your walls, floor and ceiling over a 5 and 10 year period. Consider the capital costs. Hint: State the current R value of each component. Convert to U value. Calculate new R value of each component (walls, floor and ceiling). Convert to U value. Use Q(W)=A*(change in U)*temperature change. Determine price for installation of new insulation. Determine price saved based on less heat loss through each component separately, then add all values together, and calculate per 5 years and per 10 years. Present all of this information in a table. You do not need to draw any diagrams, simply add the R value in series with your current components R values. Assume the energy cost is 25 cents kWharrow_forwardQ5Two large containers A and B of the same size are filled with different fluids. The fluids in containers A and B are maintainedat 0° C and 100° C, respectively. A small metal bar, whose initial temperature is 100° C, is lowered into container A. After1 minute the temperature of the bar is 90° C. After 2 minutes the bar is removed and instantly transferred to the othercontainer. After 1 minute in container B, the temperature of the bar rises 10°. How long, measured from the start of theentire process, will it take the bar to reach 99.9° C?arrow_forward
- Consider the vertical heat sink (see the figure) used to cool a surface at 70 0C. The room temperature is 30 0C. The dimensions are given as (H=2 cm, L=5 cm, t=1 mm, W=15 cm). If the space between the fins is arranged so that the heat transfer rate is maximum, what is the heat transfer rate from the heat sink? Properties of air: ρ=1 kg/m3, k=0.03 W/mK, ν=1.5x10-5 m2/s, cp=1 kJ/kg0C, Pr=0.7arrow_forwardAn external wall of a building has a U value of 0.50 W/m^2K. The indoor temperature is21 degrees C and the outdoor temperature is -2.0 degrees C The steady-state heat loss is calculated to be 11.5W/m^2 The wall contains a layer of insulation 40 mm thick with a conductivity of0.035 W/mK. What would the insulation thickness need to be in order toreduce the steady state heat loss by 50%? answer = 0.11m please show all workingarrow_forwardThermodynamics A hollow cylindrical insulation of inside diameter 0.2 m and outside diameter 0.4 m conducts heat radially. If another layer of insulation of the same material of thickness of 0.4 m is added, the heat flow wil be changed by what ratio?arrow_forward
- In steady state condition, the lateral surfaces of the plate are insulated, and the bottom surface is heated with a uniform heat flux. The thermal conductivity coefficient of the plate is k, and its upper surface is cooled by convection. a) Find the temperature distribution inside the plate. b) Find the temperatures at x = 0 and x = L. c) Find the amount of heat transfer transferred. NOTE: Assume one-dimensional heat conduction. h = 27 W/m2°C q" =624000W/m² k=15 W/m.°C T = 22°C L=256 cmarrow_forwardA wall made of concrete 0.305 m thick is insulated on the sides. Uniform wall temperature 10°C (283 K). The front side is in contact with the gas at a temperature of 843°C (1162 K) Convection coefficient 28.4 W/m2.K, thermal diffusivity 1.74 x 10-3 m²/hour and conductivity coefficient k = 0.935 W/m.K Count: a. The time required for the temperature on the front insulation to reach 232°C b. The temperature is at a point 0.152 m below the surface at the same time.arrow_forwardA room has a pine ceiling [ k = 0.12 W/(m•C°) ] that measures 3.0 m x 4.0 m x 2.0 cm. On a cold day, the temperature inside the room is 20°C, and the temperature in the attic above is 8°C. If 6.0 cm of glass wool insulation [ k = 0.042 W/(m•C°) ] were put in above the ceiling, how much energy would be saved in one hour? Please use gresa methodarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Understanding Conduction and the Heat Equation; Author: The Efficient Engineer;https://www.youtube.com/watch?v=6jQsLAqrZGQ;License: Standard youtube license