System Dynamics
3rd Edition
ISBN: 9780077509125
Author: Palm
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 7, Problem 7.6P
Pure water flows into a mixing tank of volume V = 300 nT at the constant volume rate of 10 m3/s. A solution with a salt concentration of s, kg/m3 flows into the tank at a constant volume rate of 2 m 7s. Assume that the solution in the tank is well mixed so that the salt concentration in the tank is uniform. Assume also that the salt dissolves completely so that the volume of the mixture remains the same. The salt concentration s()kg/m’ in the outflow is the same as the concentration in the tank. The input is the concentration s,(r), whose value may change during the process, thus changing the value of s„. Obtain a dynamic model of the concentration so.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Gas is bled from a tank. Neglecting heat transfer between the gas and the tank, show that mass and energy balances produce the differential equation:
dU / H'-U = dm / m
Here, U and m refer to the gas remaining in the tank; H' is the specific enthaly of the gas leaving the tank.
Under what conditions can one assume H'=H?
14. Through a refinery, fuel ethanol is flowing in a pipe at a velocity of 1 m/s and a pressure of 101300 Pa.
The refinery needs the ethanol to be at a pressure of 2 atm (202600 Pa) on a lower level. How far must
the pipe drop in height in order to achieve this pressure? Assume the velocity does not change. (Hint: Use
the Bernoulli equation. The density of ethanol is 789 kg/m3 and gravity g is 9.8 m/s2
A tank contains 100 gallons of brine. Three gallons of brine, each containing 2 pounds of dissolved salt, enter the tank each minute, and the mixture, assumed uniform, leaves at the rate of 2 gallons per minute. If the salt concentration in the tank is 1.6 pounds per gallon at the end of 1 hour, what was the initial concentration?
Chapter 7 Solutions
System Dynamics
Ch. 7 - Prob. 7.1PCh. 7 - Refer to the water storage and supply system shown...Ch. 7 - Prob. 7.3PCh. 7 - In Figure P7.4 the piston of area A is connected...Ch. 7 - Refer to Figure 7.1.4a. and suppose that p\ — p2=...Ch. 7 - Pure water flows into a mixing tank of volume V =...Ch. 7 - Consider the mixing tank treated in Problem 7.6....Ch. 7 - Derive the expression for the fluid capacitance of...Ch. 7 - Prob. 7.9PCh. 7 - Prob. 7.10P
Ch. 7 - 7.11 Derive the expression for the capacitance of...Ch. 7 - Air flows in a certain cylindrical pipe 1 m long...Ch. 7 - Derive the expression for the linearized...Ch. 7 - Consider the cylindrical container treated in...Ch. 7 - A certain tank has a bottom area A = 20 m2. The...Ch. 7 - A certain tank has a circular bottom area A = 20...Ch. 7 - The water inflow rate to a certain tank was kept...Ch. 7 - Prob. 7.18PCh. 7 - Prob. 7.19PCh. 7 - In the liquid level system shown in Figure P7.20,...Ch. 7 - The water height in a certain tank was measured at...Ch. 7 - Derive the model for the system shown in Figure...Ch. 7 - (a) Develop a model of the two liquid heights in...Ch. 7 - Prob. 7.24PCh. 7 - Design a piston-type damper using an oil with a...Ch. 7 - Prob. 7.26PCh. 7 - 7.27 An electric motor is sometimes used to move...Ch. 7 - Prob. 7.28PCh. 7 - Prob. 7.29PCh. 7 - Figure P7.3O shows an example of a hydraulic...Ch. 7 - Prob. 7.31PCh. 7 - Prob. 7.32PCh. 7 - Prob. 7.33PCh. 7 - Prob. 7.34PCh. 7 - Prob. 7.35PCh. 7 - Prob. 7.36PCh. 7 - Prob. 7.37PCh. 7 - (a) Determine the capacitance of a spherical tank...Ch. 7 - Obtain the dynamic model of the liquid height It...Ch. 7 - Prob. 7.40PCh. 7 - Prob. 7.41PCh. 7 - Prob. 7.42PCh. 7 - Prob. 7.43PCh. 7 - Prob. 7.44PCh. 7 - Prob. 7.45PCh. 7 - The copper shaft shown in Figure P7.46 consists of...Ch. 7 - A certain radiator wall is made of copper with a...Ch. 7 - A particular house wall consists of three layers...Ch. 7 - A certain wall section is composed of a 12 in. by...Ch. 7 - Prob. 7.50PCh. 7 - Prob. 7.51PCh. 7 - A steel tank filled with water has a volume of...Ch. 7 - Prob. 7.53PCh. 7 - Prob. 7.54PCh. 7 - Prob. 7.55P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A tank contains 1000 gal of brine in which 500 lb of salt are dissolved. Fresh water runs into the tank at the rate of 10 gal / min, and the mixture is kept uniform by stirring, runs out at the same rate. How long will it be before only 50 lb of salt are left in the tank?arrow_forwardWater is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please thanksarrow_forwardWater is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps pleasearrow_forward
- Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation!arrow_forwardA tank contains 40 lb of salt dissolved in 500 gallons of water. A brine solution is pumped into the tank at a rate of 5 gal/min; it mixes with the solution there, and then the mixture is pumped out at a rate of 5 gal/min. Determine A(t), the amount of salt in the tank at time t, if the concentration of salt in the inflow is variable and given by cin(t) = 2 + sin(t/4) lb/gal. Without actually graphing, conjecture what the solution curve of the IVP should look like. Then use a graphing utility to plot the graph of the solution on the interval [0, 300].arrow_forwarda random sample of 83 reconstructed clay vessels from the turquoise ridge Thermo Dynamics How much entropy, in kJ/K, is transferred to 20 kg of helium at 20 degrees C if the temperature is increased by 28 degrees C. Note: the pressure is maintained constant. Please solve within 30 minutes.arrow_forward
- 4. Carbon dioxide flows steadily through a varying cross-sectional-area duct such as a nozzle at a mass flow rate of 3 kg/s. The carbon dioxide enters the duct at a pressure of 1400 kPa and 200°C with a low velocity, and it expands in the nozzle to a pressure of 200 kPa. The duct is designed so that the flow can be approximated as isentropic. Determine the following parameters at each location along the duct that corresponds to a pressure drop of 200 kPa: (i) density; (ii) velocity; (iii) flow area; (iv) mach number. You may assume: • Carbon dioxide is an ideal gas with constant specific heats at room temperature; • Flow through the duct is steady, one-dimensional and isentropic. Use cp=…arrow_forwardHot water at a constant volumetric flow rate of Fh and temperature Th(t) is mixed with cold water at a constant volumetric flow rate of Fc and a constant temperature of Tc. Both streams flow into a bathtub, but because of carelessness, the water is overflowing and keeping the bathtub full of water. The bathtub volume is V, and the heat loss can be ignored. Assuming the water in the bathtub is perfectly mixed and constant density and heat capacity, derive the differential equation relating the temperature in the bathtub, T(t), to the temperature of the hot water, Th(t).arrow_forwardA circular cone-shaped container is filled with water at a level h0. At time t=0 a faucet is turned on and starts filling the cone with water at a constant flow rate Q. (a) Determine the expression for the variation of the level of water with time in terms of the initial level and volume (h0, V0) and the feed flow rate Q. (b) At what time will the water start to spill over if the cone was initially filled to 1/3 of the cone's total height? Determine a numerical value for the time in the case where the cone angle is 45o, h0=20cm and Q=2l/s.arrow_forward
- Water of density ? =998.2kg/m3 flows through a fireman’s nozzle—a converging section of pipe that accelerates the flow. The inlet diameter is d1 = 0.100 m, and the outlet diameter is d2 = 0.050 m. The average velocity, momentum flux correction factor, and gage pressure are known at the inlet (1) and outlet (2). (a) Write an expression for the horizontal force Fx of the fluid on the walls of the nozzle in terms of the given variables. (b) Verify your expression by plugging in the following values: ?1 = 1.03, ?2 = 1.02, V1 = 3 m/s, P1,gage = 137,000 Pa, and P2,gage = 0 Pa.arrow_forward2.8 The setup shown provides a liquid flow through the tissues for a physiological experiment. Taking readings h1(t) and h2(t), develop an expression for the storage rate of the liquid in the tissue. Identify your choice of control volume very carefully.arrow_forwardAir flows through a compressor under steady flow conditions. At suction V1=0.75m3/kg, v1=30m/s At discharge: V2=0.25m3/kg, v2=40m/s.. Determine the diameter ratio of the discharge pipe to that of the suction pipe. (Ans. 1:2)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY