Bundle: Steel Design, Loose-leaf Version, 6th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
6th Edition
ISBN: 9781337761505
Author: William T. Segui
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Question
Chapter 7, Problem 7.7.3P
To determine
(a)
The design of a tension member using Load and Resistance Factor Design (LRFD) method.
To determine
(b)
The design of a tension member using Allowable Strength Design (ASD) method.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
2. See connection figure below. The rivets is 7/8 in. in diameter. According to the rivert supplier,
the allowable stresses for the material are t = 15 ksi and on =
32 ksi. What is the allowable load of
the connection?
L4 x 3-1/2
W18 x 86
W24 x 117
Girder
Beam
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is
18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is
100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in
diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of
shear. Determine the maximum allowable "P" of the connection in kN.
A 3/4 in (thickness) X 5 in (height) steel plate is connected to another one through two bolts of nominal diameter 1/2 in in a zig-zag arrangement as shown. Determine the tensile strength capacity Pu of the connection. Review the three limit-states: (a) yielding in the gross area, (b) rup- ture in the overall net tensile area, and (c) block shear strength.
Chapter 7 Solutions
Bundle: Steel Design, Loose-leaf Version, 6th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
Ch. 7 - Prob. 7.3.1PCh. 7 - Prob. 7.3.2PCh. 7 - Prob. 7.4.1PCh. 7 - Prob. 7.4.2PCh. 7 - Prob. 7.4.3PCh. 7 - Prob. 7.4.4PCh. 7 - Prob. 7.4.5PCh. 7 - Prob. 7.4.6PCh. 7 - Prob. 7.6.1PCh. 7 - Prob. 7.6.2P
Ch. 7 - Prob. 7.6.3PCh. 7 - Prob. 7.6.4PCh. 7 - Prob. 7.6.5PCh. 7 - Prob. 7.6.6PCh. 7 - Prob. 7.7.1PCh. 7 - Prob. 7.7.2PCh. 7 - Prob. 7.7.3PCh. 7 - Prob. 7.8.1PCh. 7 - Determine the adequacy of the hanger connection in...Ch. 7 - Prob. 7.9.1PCh. 7 - Prob. 7.9.2PCh. 7 - Prob. 7.9.3PCh. 7 - Prob. 7.9.4PCh. 7 - Prob. 7.9.5PCh. 7 - Prob. 7.11.1PCh. 7 - Prob. 7.11.2PCh. 7 - Prob. 7.11.3PCh. 7 - Prob. 7.11.4PCh. 7 - Prob. 7.11.5PCh. 7 - Prob. 7.11.6PCh. 7 - Prob. 7.11.7PCh. 7 - Prob. 7.11.8PCh. 7 - Prob. 7.11.9PCh. 7 - Prob. 7.11.10P
Knowledge Booster
Similar questions
- Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Use attached formula picture for block shear *Please use hand written to solve this problem A channel is used as a tension member with the web of the channel welded to a 9.5 mm thick gusset plate as shown in the figure. The tension member is subjected to the following axial loads. Use LRFD Service dead load = 200 kN Wind load = 276 kN Service live load = 260 kN For channel: Fy = 345 MPa For gusset plate: Fy = 248 MPa Fu = 400 MPa Size of E 70 electrodes = 4 mm Ultimate tensile strength of E 70 electrodes = 480; Fw = 0.6(480) Questions : a) Determine the design factored tensile force. b) Determine the length of longitudinal welds "L". c) Determine the block shear strength of the gusset plate.arrow_forwardTopic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A channel shown is attached to a 12 mm gusset plate with 9-22 mm diameter A 325 bolts as shown. Use LRFD. Fnv = 300 MPa Fu = 400 MPa Fy = 248 MPa Ag = 3354 mm2 Question: Determine the capacity of the channel based on the bearing strength of the connection.arrow_forwardTopic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is 2736 sq.mm, allowable shear Fv is 150MPa, Allowable tensile stress Ft = 0.6Fy with Fy = 250 MPa. Questions: a) Design force P b) Total required length of weld using 12 mm fillet weld c) Value of “b”arrow_forward
- Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A channel is used as a tension member with the web of the channel welded to a 9.5 mm thick gusset plate as shown in the figure. The tension member is subjected to the following axial loads. Use LRFD Service dead load = 200 kN Wind load = 276 kN Service live load = 260 kN For channel: Fy = 345 MPa For gusset plate: Fy = 248 MPa Fu = 400 MPa Size of E 70 electrodes = 4 mm Ultimate tensile strength of E 70 electrodes = 480; Fw = 0.6(480) Questions : a) Determine the design factored tensile force. b) Determine the length of longitudinal welds "L". c) Determine the block shear strength of the gusset plate.arrow_forwardThe plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.arrow_forwardAssignment No. 3 Due 1. For the tension member shown, compute the following. a. The tensile design strength. b. The allowable tensile strength. 6" PL 4x6 A36 steel Weldarrow_forward
- A bolted connection shown consists of two plates 300mm x12mm connected by 4 - 22 mm diameter bolts. Edge distances = 75mm dhole for tensile and rupture = db + 3 mm dhole for bearing strength for Lc = db + 1.5 mm Fy = 248 Mpa Fu = 400 Mpa Fn = 330 Mpa Use LRFD design method. Determine the design strength due to the gross yielding of plates. (kN)arrow_forward2 ISA 75 x 75 x 8 carry a load of 150 kN and are placed back to back through a 6 mm gusset plate. The permissible shear stress is 100 MPa and bearing stress is 300 MPa. Design the riveted connection and show the arrangement with a neat sketch.arrow_forwardDesign a welded connection for an MC9x23.9 of A572 Grade 50 steel connected to a 3/8-inch-thick gusset plate. The gusset plate is A36 steel. Show your results on a sketch, complete with dimensions. = 3/8" D= L = MC9 X 23.9arrow_forward
- The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivetsarrow_forwardTopic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A tension member consists of a double angle section with long legs back to back. The angles are attached to a 9.5 mm thick gusset plate. Fu = 400 MPa Fy = 248 MPa for angular section. Fw = 480 MPa for 8 mm fillet weld. Reduction factor U = 0.80 Prop. of One Angle L 125m x 75m x 12.7 m A= 2419 mm2 y=44.45 mm Questions: a) Compute the design strength capacity of one angle. b) Compute the base metal shear strength (gusset plate) per unit length. c) Compute the length L1 and L2.arrow_forwardTopic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu=483.33 MPa. Fv = 0.30 Fu Questions: a) Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. b) Determine the length of side fillet weld required at the heel. c) Determine the length of side fillet weld required at the toe.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Steel Design (Activate Learning with these NEW ti...Civil EngineeringISBN:9781337094740Author:Segui, William T.Publisher:Cengage Learning
Steel Design (Activate Learning with these NEW ti...
Civil Engineering
ISBN:9781337094740
Author:Segui, William T.
Publisher:Cengage Learning