Concept explainers
(a)
The normal stress
(a)
Answer to Problem 97P
The normal stress
Explanation of Solution
Given information:
The state of plane stress components are
The uniaxial tension for the aluminum alloy is
The uniaxial compression for the aluminum alloy is
Calculation:
Calculate the average normal stress
Substitute
Calculate the value of
Substitute
Calculate principal stresses
Substitute
Hence, stress point lies in the first quadrant.
Sketch the Mohr’s criterion for the machine component as shown in Figure 1.
Refer to Figure 1.
The principal stresses for (a) in the first quadrant of boundary.
Calculate the value of
Substitute
Therefore, the normal stress
(b)
The normal stress
(b)
Answer to Problem 97P
The normal stress
Explanation of Solution
Given information:
The state of plane stress components are
The uniaxial tension for the aluminum alloy is
The uniaxial compression for the aluminum alloy is
Calculation:
Calculate the average normal stress
Substitute
Calculate the value of
Substitute
Calculate principal stresses
Substitute
Hence, stress point lies in the forth quadrant.
Refer to Figure 1.
The principal stresses for (b) in the forth quadrant of boundary.
Calculate the value of
Substitute
Therefore, the normal stress
(c)
The normal stress
(c)
Answer to Problem 97P
The normal stress
Explanation of Solution
Given information:
The state of plane stress components are
The uniaxial tension for the aluminum alloy is
The uniaxial compression for the aluminum alloy is
Calculation:
Calculate the average normal stress
Substitute
Calculate the value of
Substitute
Calculate principal stresses
Substitute
Hence, stress point lies in the forth quadrant.
Refer to Figure 1.
The principal stresses for (b) in the forth quadrant of boundary.
Calculate the value of
Substitute
Therefore, the normal stress
Want to see more full solutions like this?
Chapter 7 Solutions
Loose Leaf For Mechanics Of Materials Format: Looseleaf
- A torque of magnitude T=12 kN·m is applied to the end of a tank containing compressed air under a pressure of 8 MPa. Knowing that the tank has a 180-mm inner diameter and a 12-mm wall thickness, determine the maximum normal stress and the maximum in-plane shearing stress in the tank.arrow_forwardFor the state of stress shown, it is known that the normal and shearing stresses are directed as shown and that σx= 14 ksi, σy= 9 ksi, and σmin= 5 ksi. Determine (a) the orientation of the principal planes, (b) the principal stress σmax, (c) the maximum in-plane shearing stressarrow_forwardA standard-weight steel pipe of 12-in. nominal diameter carries water under a pressure of 400 psi. (a) Knowing that the outside diameter is 12.75 in. and the wall thickness is 0.375 in., determine the maximum tensile stress in the pipe. (b) Solve part a, assuming that an extra-strong pipe is used, of 12.75-in. outside diameter and 0.5-in. wall thickness.arrow_forward
- A compressive member of a structure is of 25 mm square cross-section and carries a load of 50 kN. Determine, from first principles, the normal, tangential, and resultant stresses on a plane inclined at 60° to the axis of the bar.arrow_forwardFor the state of stress shown, it is known that the normal and shearing stresses are directed as shown and that σx = 15.5 ksi, σy = 9 ksi, and σmin = 5 ksi. Determine the orientation of the principal planes. Determine the principal stress σmax. Determine the maximum in plane shearing stressarrow_forwardA steel pipe of 400-mm outer diameter is fabricated from 10-mm-thick plate by welding along a helix that forms an angle of 20°with a plane perpendicular to the axis of the pipe. Knowing that the maximum allowable normal and shearing stresses in the directions respectively normal and tangential to the weld are σ = 60 MPa and τ = 36 MPa, determine the magnitude P of the largest axial force that can be applied to the pipe.arrow_forward
- A composite shaft shown, composed of a steel (G = 77 GPa) core inside an aluminum (G = 25 GPa) jacket, carries a torque, T = 10 kN-m. The shaft is designed such that the aluminum jacket will fail first upon the application of the torque. 1) If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the aluminum jacket, that can carry the torque.2) What must be the minimum shear strength of steel such that the aluminum jacket will fail first?3) Determine the maximum angle of twist that can be applied to the shaft.arrow_forwardA 40-kN axial load is applied to a short wooden post that is supported by a concrete footing resting on undisturbed soil. Determine (a) the maximum bearing stress on the concrete footing, (b) the size of the footing for which the average bearing stress in the soil is 145 kPa.arrow_forwardA cast-iron tube is used to support a compressive load. Knowing that E5 10 3 106 psi and that the maximum allowable change in length is 0.025%, determine (a) the maximum normal stress in the tube, (b) the minimum wall thickness for a load of 1600 lb if the outside diameter of the tube is 2.0 in.arrow_forward
- The aluminum rod ABC (E = 10.1 × 106 psi), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E = 29 × 106 psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 27 ksi. The minimum required diameter of the steel rod is in.arrow_forwardKnowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the alumi-num bar will be equal to –11 ksi, (b) the corresponding exact length of the aluminum bar.arrow_forwardFor the steel truss and loading shown, determine the magnitude of the deformation (in inches) of member BE, knowing that the cross-sectional area is 2.42 sq. in, x = 13.9 ft, y = 7.1 ft, P = 27089 lb, and E = 29071219 psi. Round off the final answer to four decimal places.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY