SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
10th Edition
ISBN: 9781260163155
Author: BUDYNAS
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 8, Problem 16P
A 2-in steel plate and a 1-in cast-iron plate are compressed with one bolt and nut. The bolt is
- (a) Determine a suitable length for the bolt, rounded up to the nearest
- (b) Determine the bolt stiffness.
- (c) Determine the stiffness of the members.
8-15 Repeat Prob. 8-14 with the addition of one
8-16 Repeat Prob. 8-14 with the cast-iron plate having a threaded hole to eliminate the nut.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 0.5-in.-diameter steel [E= 30,000 ksi] bolt (1) is placed in a copper tube (2). The copper [E= 16,000 ksi] tube has an outside diameter of 1.00 in., a wall thickness of 0.125 in., and a length of L= 8.0 in. Rigid washers, each with a thickness of t= 0.125 in., cap the ends of the copper tube. The bolt has 20 threads per inch. This means that each time the nut is turned one complete revolution, the nut advances 0.05 in. (i.e., 1/20 in.). The nut is hand-tightened on the bolt until the bolt, nut, washers, and tube are just snug, meaning that all slack has been removed from the assembly but no stress has yet been induced. What stresses are produced in the bolt and in the tube if the nut is tightened an additional quarter turn past the snug-tight condition?
A 30-mm thick AISI 1020 steel plate is sandwiched between two 20-mm thick2024-T3 aluminum plates and compressed with a bolt and nut with no washers. The boltis M12 × 1.75, property class 9.8. Draw a sketch of the joint and,(a) Determine a suitable length for the bolt, rounded up to the nearest 5 mm. (b) Determine the bolt stiffness.(c) Determine the stiffness of the members and joint stiffness.
load of 12 kN is raised by means of a screw jack. The mean diameter of the square threaded screw is 48 mm and the pitch is 12 mm. A force of 180 N is applied at the end of a lever to raise the load. Determine the length of the lever to be used and the mechanical advantage obtained. the screw self-locking? Take µ = 0.12.
Chapter 8 Solutions
SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
Ch. 8 - A power screw is 25 mm in diameter and has a...Ch. 8 - Using the information in the footnote of Table...Ch. 8 - Show that for zero collar friction the efficiency...Ch. 8 - A single-threaded power screw is 25 mm in diameter...Ch. 8 - The machine shown in the figure can be used for a...Ch. 8 - The press shown for Prob. 8-5 has a rated load of...Ch. 8 - For the screw clamp shown, a force is applied at...Ch. 8 - The C clamp shown in the figure for Prob. 8-7 uses...Ch. 8 - Find the power required to drive a 1.5-in power...Ch. 8 - A single square-thread power screw has an input...
Ch. 8 - Prob. 11PCh. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - Prob. 13PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Repeat Prob. 8-14 with the addition of one 12 N...Ch. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - Two identical aluminum plates are each 2 in thick,...Ch. 8 - Prob. 18PCh. 8 - A 30-mm thick AISI 1020 steel plate is sandwiched...Ch. 8 - Prob. 20PCh. 8 - Prob. 21PCh. 8 - Prob. 22PCh. 8 - A 2-in steel plate and a 1-in cast-iron plate are...Ch. 8 - An aluminum bracket with a 12-in thick flange is...Ch. 8 - An M14 2 hex-head bolt with a nut is used to...Ch. 8 - A 34 in-16 UNF series SAE grade 5 bolt has a 34-in...Ch. 8 - From your experience with Prob. 8-26, generalize...Ch. 8 - Prob. 28PCh. 8 - Prob. 29PCh. 8 - Prob. 30PCh. 8 - For a bolted assembly with eight bolts, the...Ch. 8 - Prob. 32PCh. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - 8-33 to 8-36 The figure illustrates the...Ch. 8 - Prob. 37PCh. 8 - Prob. 38PCh. 8 - 837 to 840 Repeat the requirements for the problem...Ch. 8 - Prob. 40PCh. 8 - 841 to 844 For the pressure vessel defined in the...Ch. 8 - Prob. 42PCh. 8 - Prob. 43PCh. 8 - Prob. 44PCh. 8 - Bolts distributed about a bolt circle are often...Ch. 8 - The figure shows a cast-iron bearing block that is...Ch. 8 - Prob. 47PCh. 8 - Prob. 48PCh. 8 - Prob. 49PCh. 8 - Prob. 50PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - Prob. 52PCh. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 851 to 854 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - 855 to 858 For the pressure cylinder defined in...Ch. 8 - For the pressure cylinder defined in the problem...Ch. 8 - A 1-in-diameter hot-rolled AISI 1144 steel rod is...Ch. 8 - The section of the sealed joint shown in the...Ch. 8 - Prob. 61PCh. 8 - Prob. 62PCh. 8 - Prob. 63PCh. 8 - Prob. 64PCh. 8 - Using the Goodman fatigue criterion, repeat Prob....Ch. 8 - The figure shows a bolted lap joint that uses SAE...Ch. 8 - Prob. 67PCh. 8 - A bolted lap joint using ISO class 5.8 bolts and...Ch. 8 - Prob. 69PCh. 8 - The figure shows a connection that employs three...Ch. 8 - A beam is made up by bolting together two cold...Ch. 8 - Prob. 72PCh. 8 - Prob. 73PCh. 8 - Prob. 74PCh. 8 - A vertical channel 152 76 (see Table A7) has a...Ch. 8 - The cantilever bracket is bolted to a column with...Ch. 8 - Prob. 77PCh. 8 - The figure shows a welded fitting which has been...Ch. 8 - Prob. 79PCh. 8 - Prob. 80PCh. 8 - Prob. 81P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Figure 8-19 is a cross-section of ASTM A36. A total of N bolts are to be used to resist a separating force of 7258.97N is one bolt. A) Determine kb,km, and C B) Determine the realized load factor for overload, the yielding factor of safety, and the load factor of joint separation.arrow_forwardA semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.arrow_forwardA screw clamp shown in the figure has a handle with diameter 5 mm made of cold-drawn AISI 1006 steel (table E18 - page 1195). The overall length of the hand is 75 mm. The screw is M 12 coarse (table 8-1) and is 145 mm long, overall. Distance A is 50 mm. The clamp will accommodate parts up to 105 mm high.a) What is the value of screw torque that causes the handle to bend permanently?b) If the collar friction is neglected and if the thread friction is 0.075, what is the screw force value that causes the handle to bend permanently?c) What is the value of clamping force, which will cause the screw to buckle?d) Are there any other stresses or possible failures to be checked?e) If yes, calculate them.arrow_forward
- The figure gives the cross-section of a grade 25 cast-iron pressure vessel. A total of N bolts are to be used to resist a separating force of 150 kN. (a) Determine kb, km, and C. (b) Find the number of bolts required for a load factor of 2 where the bolts may be reused when the joint is taken apart. (c) With the number of bolts obtained in part (b), determine the realized load factor for overload, the yielding factor of safety, and the load factor for joint separation. Use (SI) units as it appliesarrow_forwardA semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.arrow_forwardA typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: Mean coil diameter = 100mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: Mean coil diameter = 75 mm No. of turns = 20 Both the springs are of equal initial length when unloaded. If the working stress for each spring is to be the same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following: a. Diameter of steel wire for inner spring b. Stiffness of inner spring c. Stiffness of the compound springarrow_forward
- Determine the size of a piston rod subjected to a total load of having cyclic fluctuations from 15 kN in compression to 25 kN in tension. The endurance limit is 360 MPa and yield strength is 400 MPa. Take impact factor = 1.25, factor of safety = 1.5, surface finish factor = 0.88 and stress concentration factor = 2.25.arrow_forwardA typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: mean coil diameter = 100 mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: mean coil diameter = 75 mm No. of turns = 20Both the springs are of equal initial length when unloaded. Ifthe working stress for each spring is to be same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following:a. Diameter of steel wire for inner spring. b. Stiffness of inner springc. Stiffness of the compound spring. I need answer ASAP. Thank you!arrow_forwardA single L8x6x1/2 (A36 steel) is used as a tension brace in a multi-story building. The 8 inch leg of the angle is attached to a gusset plate with two lines of four ¾ inch Ø bolts at a spacing of 3 inches. Determine the shear lag factor (consider Case 2 & 8) and the effective net area. Considering yielding and net section rupture, determine the design strength by LRFD and the allowable strength by ASD. (PLEASE SOLVE THIS ONE WITH THE BOLD TEXT)arrow_forward
- given: - initial length of steel tube= 200mm - aluminum rod is 0.175 mm shorter than steel tube. - l=0.175 mm properties of materials - ALUMINUM: coefficient of linear expansion: 23x10-6 /C modulus of elasticitty= 70 GPa - STEEL Coeficient of linear expansion: 11x10-6 /C Modulus of elasticity: 200 GPa *NEGLECT SHEAR AND LATERAL DEFORMATIONS. REQUIRED: - which of the two members will have contact on the rigid switch first and at what temperature - axial stress that would develop on 1st member after the 2nd material fills in the gap safely. PLS. SHOW FULL SOLUTIONS WITH BRIEF EXPLANATIONS AND NECESSARY DIAGRAMS...arrow_forwardA right angled bell crank lever is to be designed to raise a load of 5 kN at the short arm end. The lengths of short and long arms are 100 and 450 mm respectively. The lever and the pins are made of steel 30C8 (S = 400 N/mm2). And the factor of safety is 5.the permissible bearing pressure on the pin is 10 N/mm². The lever has a rectangular cross section and the ratio of width to thickness is 3:1. The length to diameter ratio of the fulcrum pin is 1.25:1. Calculate (i) The diameter and length of the fulcrum pin (ii) The dimensions of the cross section.arrow_forwardThe load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figuresarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License