Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780133494839
Author: Mott
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 8, Problem 8.59PP
Water at
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is the Reynold’s number for a flow of oil (SG = 0.80, ? = 0.00200 lb-s/ft2) in a 6-in diameter pipe at a flow rate of 10ft3/s. Is the flow laminar or turbulent?
thank you!
Benzene (SG=0.86) at 60°C is flowing at 25 L/min in a DN 25 Schedule 80 steel pipe. Is the flow laminar or turbulent? Explain.
Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40 steel pipe if the vol- ume flow rate is 0.25 ft/s: (a) water at 60°F. (b) acetone at 77 F, (c) castor oil at 77 E, and (d) SAE 10 oil at 210°(Sg 0.87),
Chapter 8 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 8 - A 4-in-ductile iron pipe carries 0.20ft3/s of...Ch. 8 - Calculate the minimum velocity of flow in ft/s of...Ch. 8 - Calculate the maximum volume flow rate of fuel oil...Ch. 8 - Calculate the Reynolds number for the flow of each...Ch. 8 - Determine the smallest metric hydraulic copper...Ch. 8 - In an existing installation, SAE 10 oil (sg = 0.89...Ch. 8 - From the data in Appendix C, we can see that...Ch. 8 - Compute the Reynolds number for the flow of 325...Ch. 8 - Benzene (sg = 0.86 ) at 60c C is flowing at 25...Ch. 8 - Hot water at 80 C is flowing to a dishwasher at a...
Ch. 8 - A major water main is an 18 -in ductile iron pipe....Ch. 8 - ]8.12 An engine crankcase contains SAE 10 motor...Ch. 8 - Repeat Problem 8.12 for an oil temperature of 160...Ch. 8 - At approximately what volume flow rate will propyl...Ch. 8 - SAE 30 oil (sg = 0.89 ) is flowing at 45 L/min...Ch. 8 - Repeat Problem 8.15 for an oil temperature of 160...Ch. 8 - Repeat Problem 8.15, except the tube is 50 mm...Ch. 8 - Repeat Problem 8.17 for an oil temperature of 0 C.Ch. 8 - The lubrication system for a punch press delivers...Ch. 8 - After the press has run for some time, the...Ch. 8 - A system is being designed to carry 500 gal/min of...Ch. 8 - The range of Reynolds numbers between 2000 and...Ch. 8 - The water line described in Problem 8.22was a cold...Ch. 8 - In a dairy, milk at 100 F is reported to have a...Ch. 8 - In a soft-drink bottling plant, the concentrated...Ch. 8 - ]8.26 A certain jet fuel has a kinematic viscosity...Ch. 8 - Crude oil is flowing vertically downward through...Ch. 8 - Water at 75 C is flowing in a standard hydraulic...Ch. 8 - Fuel oil is flowing in a 4 -in Schedule 40 steel...Ch. 8 - A 3-in Schedule 40 steel pipe is 5000 ft long and...Ch. 8 - Benzene at 60 C is flowing in a DN 25 Schedule 80...Ch. 8 - As a test to determine the effective wall...Ch. 8 - Water at F flows from a storage tank through ft...Ch. 8 - A water main is an 18 -in-diameter concrete...Ch. 8 - Figure 8.12shows a portion of a fire protection...Ch. 8 - A submersible deep-well pump delivers 745 gal/h of...Ch. 8 - On a farm, water at 60 F is delivered from a...Ch. 8 - Figure 8.15 shows a system for delivering lawn...Ch. 8 - A pipeline transporting crude oil (sg = 0.93 ) at...Ch. 8 - For the pipeline described in Problem 8.39,...Ch. 8 - Water at 10 C flows at the rate of 900 L/min from...Ch. 8 - For the system shown in Fig. 8.17, compute the...Ch. 8 - Fuel oil (sg = 0.94 ) is being delivered to a...Ch. 8 - Figure 8.18 shows a system used to spray polluted...Ch. 8 - In a chemical processing system, the flow of...Ch. 8 - Water at 60 F is being pumped from a stream to a...Ch. 8 - For the pump described in Problem 8.46, if the...Ch. 8 - Gasoline at 50 F flows from point A to point B...Ch. 8 - Figure 8.20 shows a pump recirculating 300 gal/min...Ch. 8 - Linseed oil at 25 C flows at 3.65 in a standard...Ch. 8 - Glycerin at 25 C flows through a straight...Ch. 8 - Water at 75 C flows in a standard hydraulic copper...Ch. 8 - Benzene (sg = 0.88 ) at 60 C, flows in a DN 25...Ch. 8 - Water at 80 F flows in a 6 -in coated ductile iron...Ch. 8 - Water at 50 F flows at 15.0 ft3/s in a concrete...Ch. 8 - Water at 60 F flows at 1500 gal/min in a 10 -in...Ch. 8 - ]8.57 A liquid fertilizer solution (sg = 1.10 )...Ch. 8 - Crude oil (sg = 0.93 ) at 100 C flows at a rate of...Ch. 8 - Water at 65 C flows in a DN 40 Schedule 40 steel...Ch. 8 - Propyl alcohol flows in a standard hydraulic...Ch. 8 - ]3.61 Water at 70 F flows in a 12 -in-diameter...Ch. 8 - Heavy fuel oil at 77 F flows in a 6 -in Schedule...Ch. 8 - Water flows at a rate of 1.50ft3/s through 550 ft...Ch. 8 - Compute the energy loss as water flows in a...Ch. 8 - ]8.65 A water main is an 18 -in-diameter concrete...Ch. 8 - A fire protection system includes 1500 ft of 10...Ch. 8 - ]8.67 A standard hydraulic copper tube, 120 mm...Ch. 8 - Compute the energy loss as 2.0ft3/s of water flows...Ch. 8 - It is desired to flow 2.0ft3/s of water through...Ch. 8 - Specify a suitable size of new, clean Schedule 40...Ch. 8 - For the pipe selected in Problem 8.70, compute the...Ch. 8 - Compare the head loss that would result from the...Ch. 8 - In Problem 6.107, a theoretical flow rate of water...Ch. 8 - A pipeline is needed to transport medium fuel oil...Ch. 8 - Medium fuel oil at 25 C is to be pumped at a flow...Ch. 8 - A tremendous amount of study has gone into the...Ch. 8 - In a given installation, it is determined that the...Ch. 8 - "Laminar" fountains have become quite popular due...Ch. 8 - Use PIPE-FLO to model a straight horizontal run of...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- The static head at a certain station on a 101.6 mm schedule 40, clean iron cold pipe is 70.69 m The static head is to be determined for a station 162.4 m farther along the pipe in the direction of flow,and where the pipe is 10.14 m higher than station 1. Between the stations are two elbows. Flow rateis 1452 l/min.arrow_forwardBenzene flows through a 100 mm diameter pipe at a mean velocity of 3 m/s. Find discharge in liter per second.arrow_forwardQ.2) Determine the friction factor, “f” if Ethyl Alcohol at 25 C is flowing at 5.3 m/sec in a standard DN 40 Schedule 80 steel pipe.arrow_forward
- Convert 50 GPM to ft/s in a 4" Sch 40 pipearrow_forwardWater at 15 °C flows through a 300 mm steel pipe with roughness 3 mm. The corresponding head loss is measured as 6 m. a. What type of pipe flow problem is this? Type I, Ii or II? Explain why? b. Calculate the flow rate using an iterative procedure and Moody chart c. Calculate the power required to maintain flow d. Calculate the shear stress at the wallsarrow_forwardDetermine the flow rate in pounds per hour of water at 68°F through a 1000-ft length of horizontal 8-in schedule 40 steel pipe (internal diameter 0.7981 in) under a pressure difference of 3.00 psi. k/D = 2.3x10^4.arrow_forward
- Calculate the Reynolds number for the flow of each of the following fluids in a 2-in Schedule 40 steel pipe if the vol-ume flow rate is 0.25 ft3 / s: (a) water at 60F, (b) acetone at 77F, (c) castor oil at 77F, and (d) SAE 10 oil at 210F (sg = 0.87).arrow_forwardThe water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.arrow_forwardWhen water at 20°C (68°F) flows through 6 m (20 ft) of 50 mm (2 in.) smooth brass pipe,the head lost is 0.3 m (1 ft). Calculate the flowratearrow_forward
- How many gal/hr of water at 68 deg F can be delivered through a 1320-ft length of smooth 6.00 in i.d. pipe under a pressure difference of 0.25 psi. Assume that the pipe is “hydraulically smooth”arrow_forwardFor the flow of 12.9 L/min of water at 75 degrees Celcius in a plastic pipe, 16mm OD x 1.5mm wall, compute the expected maximum velocity of flow. Answer is 1.95m/s. Please show how to solve.arrow_forwardA2: FLUID FLOW, FLOW RATE & PRESSURE DROPProblem:4. Determine the average velocity in m/s for water flow in a 2 in diameter pipe, Schedule 40 chlorinated polyvinyl chloride (CPVC) pipe (2.375 in outside diameter and 2.047 in inside diameter) carrying cold water at a volumetric flow rate of 40 gpm.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License