THINKING LIKE AN ENGINEER W/ACCESS
17th Edition
ISBN: 9781323522127
Author: STEPHAN
Publisher: PEARSON C
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 9, Problem 10RQ
- 10. The Peclet number is used in heat transfer in general and forced convection calculations in particular. It is a function of the two other dimensionless groups, the Reynolds number and the Prandtl number. Determine the functional form of these dimensionless groups, using Rayleighʼs method. The problem depends on the following variables:
ρ = Liquid density | [=] kg/m3 |
Cp = Specific heat of liquid | [=] J/(g oC) |
µ = Liquid viscosity | [=] kg/(m s) |
a = Thermal diffusivity | [=] m2/s |
k = Thermal conductivity of the plate | [=] W/(m oC) |
x = Distance from edge of the plate | [=] m |
V = Liquid velocity | [=] m/s |
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Important variables in a particular water machine are: Fluid density (ρ), impeller angular velocity (ω), impeller diameter (D), volume flow rate (), fluid viscosity (µ), head (gH). In fact, (gH) shows the energy that the fluid unit mass receives from or gives to the machine, independent of gravitational acceleration (g). Therefore, gH value is used instead of H. Important sizes in terms of the operation of the water machine are power (P), (gH) and efficiency ( h). Derive dimensionless numbers by typing these two parameters based on the above variables and applying Buckingham's p method (repeating variables method).
Consider the following equation. All three of the terms in parentheses are dimensionless groups. Because kC is difficult to determine directly, the other variables are measured and kC is calculated from the given equation.
What is the estimated value of kC? What are the units of kC? Show your work. The following values were measured: D = 8.0 mm, DAB = 0.475 cm2/s, μ = 1.12 x 10–3 N-s/m2, ρ = 1.00 x 10–3 g/cm3, v = 15.0 m/s.
Note: Given Equation attached below
If the given Pi is 3.14159
Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg
Liquid sample: density = 4 ml; time of flow = 4.5 seconds
What is the pressure in MKS unit and CGS unit?
What is its viscosity?
If the weight is 8.5 g, what is its density?
What is its kinematic viscosity?
What is its fluidity?
Chapter 9 Solutions
THINKING LIKE AN ENGINEER W/ACCESS
Ch. 9.1 - The heat loss (Q/t, in units of joules per second...Ch. 9.2 - A simple expression for the velocity of molecules...Ch. 9.2 - What are the dimensions of the value 6 in the...Ch. 9.4 - The Euler number is a function of the pressure...Ch. 9 - Complete the following table. Dimensions ...Ch. 9 - Complete the following table. Dimensions ...Ch. 9 - Calculate the numerical value of each of the...Ch. 9 - Calculate the numerical value of each of the...Ch. 9 - A fluid with a specific gravity of 0.91 and a...Ch. 9 - Brine, with a density of 1.25 grams per cubic...
Ch. 9 - When a simple turbine is used for mixing, the...Ch. 9 - History suggests that Newton developed his idea...Ch. 9 - It is proposed to create a set of dimensionless...Ch. 9 - 1. While researching fluid dynamics, you come...Ch. 9 - 2. While researching fluid dynamics, you came...Ch. 9 - 3. While researching fluid dynamics, you come...Ch. 9 - 4. The Arrhenius number (Ar) is the dimensionless...Ch. 9 - 5. The Biot number (Bi) is the dimensionless...Ch. 9 - 6. A biodegradable fuel having a specific gravity...Ch. 9 - 7. A sludge mixture having a specific gravity of...Ch. 9 - 8. Water (specific gravity = 1.02; viscosity =...Ch. 9 - 9. We have been asked to determine a set of...Ch. 9 - 10. The Peclet number is used in heat transfer in...Ch. 9 - 11. When a fluid flows slowly across a flat plate...Ch. 9 - 12. In modeling the flow of liquid in a piping...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What types of polymers are most commonly blow molded?
Degarmo's Materials And Processes In Manufacturing
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Determine the velocity of block D if end A of the rope is pulled down with a speed of vA = 3 m/s.
Engineering Mechanics: Dynamics (14th Edition)
Steady state conduction rate to the warm compressor to the net power produces theoretically by thermodynamic ba...
Introduction to Heat Transfer
How is the hydrodynamic entry length defined for flow in a pipe? Is the entry length longer in laminar or turbu...
Fluid Mechanics Fundamentals And Applications
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Fluid mechanics theory The power input P to a centrifugal pump is a function of the volume flow Q, impeller diameter D, rotational rate ω, and the density ρ and viscosity μ of the fluid. Determine the three dimensionless numbers. Use M, L, T as your primary dimensions and ω, ρ and D as repeatingvariables.arrow_forward01: The drag force (F) of an aircraft during flight depends upon the length of aircraft flow velocity air viscosity density p. and bulk modulus of air K. (1) Derive the relationship between the above variables and the drag force by using Buckingham's II theorem . (2) Explain the physical meaning of the obtained dimensionless groups .arrow_forwardUse dimentional analysis to evaluate that in a problem involving shallow water waves (figure 6), both the Froude number and the Reynold's number are relevant dimensionless parameters. The wave speed, c of waves on the surface of a liquid is a function of depth h, gravitational acceleration g, fluid density, p and fluid viscosity μ. Manipulate your II's to get the parameters into the following form: Fr = c/(gh)1/2= f(Re) , where Re = pch/μarrow_forward
- The Reynolds number is a dimensionless group defined as follows for a liquid that flows through a pipe: Re = Dvρ / μ where D is the diameter of the pipe, v is the velocity of the fluid, ρ is its density and µ its viscosity. When the Reynolds number value is less than 2100, the flow is laminar, that is, the liquid it moves in lines of smooth flow. For Reynolds numbers greater than 2100, the flow is turbulent, characterized by considerable agitation. Liquid Methyl Ethyl Ketone (MEK) flows through 2067 '' ID tubing and through an average velocity of 0.48 ft / s. If the fluid temperature is 20 ° C, the density of the MEK The liquid is 0.805 g / cm and the viscosity is 0.43 cP (1 cP = 1.00 x 10 kg / (m-s)]. Determine the Reynolds number for MEK flow conditions. (Round the final result to a whole number without decimals).arrow_forwardThe pressure drop per unit length in horizontal pipe flow,∆ p/L , depends on the fluid density ρ , viscosity μ , diameterD , and volume flow rate Q . Rewrite this function in termsof pi groups.arrow_forwardMeasurements at a certain point of a pipe have been done where the following parameters were recorded: Fluid of density = 887 kg/m3, Fluid velocity = 4 m/s, Pressure= 11.3 KN/m2 If the total energy per unit weight at this point = 32 m, then the potential energy is:arrow_forward
- At any time, approximately 20 volcanoes are actively erupting on the Earth, and 50–70 volcanoes erupt each year. Over the past 100 years, an average of 850 people have died each year from volcano eruptions. As scientists and engineers study the mechanics of lava flow, accurately predicting the flow rate (velocity) of the lava is critical to saving lives after an eruption. Jeffrey’s equation captures the relationship between flow rate and viscosity as: where ρ is the density of the lava, g is gravity, t is the flow thickness, α is the slope, and m is the lava viscosity. Typical values are given as follows for the flow rate: m= 4x103 kg/(m.s) ±1% ρ= 2.5 g/cm3 ±1% t= 28 cm ±0.5 cm α= 10° ±1 ° g= 9.81 m/s²arrow_forwardThe power P required to drive a propeller is known to depend on the diameter of the propeller D, the density of fluid ρ, the speed of sound a, the angular velocity of the propeller ω, the freestream velocity V , and the viscosity of the fluid µ. (a) How many dimensionless groups characterize this problem? (b) If the effects of viscosity are neglected, and if the speed of sound is not an important variable, express the relationship between power and the other variables in nondimensional form. (c) A one-half scale model of a propeller is built, and it uses Pm horsepower when running at a speed ωm. If the full-scale propeller in the same fluid runs at ωm/2, what is its power consumption in terms of Pm if the functional dependence found in part (b) holds? What freestream velocity should be used for the model test?arrow_forwardAt a sudden contraction in a pipe the diameter changes from D, to D2. The pressure drop, Ap, which develops across the con- traction is a function of D, and Dz, as well as the velocity, V, in the larger pipe, and the fluid density, p, and viscosity, u. Use D, V, and u as repeating variables to determine a suitable set of dimensionless parameters. Why would ti be incorrect to include the velocity in the smaller pipe a sa nadditional variable?arrow_forward
- Let the velocity, u (m/s), specific heat, cp (kJ/(kg K)), and temperature, T (K), be used to define a dimensionless number given by u2cpaTb. The powers must be a=[Blank-1] and b=[Blank-2].arrow_forwardCold water enters a pipe, where it is heated by an external heat source . The inlet and outlet water temperatures are Tin and Tout, respectively. The total rate of heat transfer Q. from the surroundings into the water in the pipe is Q. = m·cp(Tout − Tin) where m . is the mass flow rate of water through the pipe, and cp is the specific heat of the water. Write the primary dimensions of each additive term in the equation, and verify that the equation is dimensionally homogeneous. Show all your work.arrow_forwardVolumetric flow rate, Q, of a pump is a function of impeller diameter d, fluid velocity V,pressure difference P, fluid density and viscosity .a) (15P) Determine dimensionless groups.b) (20P) A test is to be performed for a large pump that delivers 1.5 m3/s of water from 40 cmdiameter impeller with pressure rise of 400 kPa. For the test, a model with an 8 cm diameter impelleris to be used. What flow rate should be used and what would be the pressure rise in model pumparrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
Unit Conversion the Easy Way (Dimensional Analysis); Author: ketzbook;https://www.youtube.com/watch?v=HRe1mire4Gc;License: Standard YouTube License, CC-BY