3.) At room temperature the electrical conductivity of PbTe is 500 (N-m)1 whereas the electror and hole mobilities are 0.16 and 0.075 m²/V-s, respectively. Compute the intrinsic carrier concentration for PbTe at room temperature.
Q: 5) When you consider the voltammetric techniques, how is polarography different than the others?…
A: 5. THE SHAPE OF THE POLAROGRAPHY IS OF SIGMOID SHAPE IT IS ELECTROANALLY TECHNIQUE THAT IS APPLIED…
Q: What is the relative amount in percentage of η phase in 90 wt% Zn-10 wt% Cu at 400°C
A: In an alloy, components represent the elements and compounds mixed initially to form that alloy.…
Q: Which one of the following compounds would adsorb most strongly to silica gel? SCH3 Br -CO2H A B E
A: Silica gel is a compound of Silicon and oxide. Its molecular formula is SiO2 and is a network solid…
Q: Why is MgCl2•6H2O added in a preparation of EDTA solution?
A: Standard Solution of ethylene diamine Tetra Acetate, EDTA is prepared by mixing the EDTA salt with…
Q: Which is correct for polarography? I-polarography is an amperometry method conducted with a dripping…
A: Polarography technique is used to determine the molecules are oxidation or other reduction at…
Q: Which one below is not one of the reasons for adding inorganic additives to organic matrix in…
A: They combine the advantages of the inorganic material (ex: rigidity, thermal stability) and the…
Q: b) Suggest a material (not one already mentioned in the lecture course) that would be an appropriate…
A: MLI (Multi-Layer Insulation) is normally made of multiple reflective films made of polyester and…
Q: In ammonia stripping, hitrogen is removed from wastewater by volatilization of NH3. Would ammonia…
A:
Q: The exchange capacity of an ion-exchange resin is defined as the number of moles of charged sites…
A: The exchange capacity of an ion exchange resin is defined as the number of moles of charged sites…
Q: 1.A compound Y (150.0 g/mol) in a 1.00 cm quartz cell has an extinction coefficient (ε) of 23,150 at…
A: Answer to Question No:1 The energy of a photon can be calculated by the famous formula- E=hcλwhere,…
Q: a. The structure of a standard C4 group chemically bonded to a silica surface through a silyl ether…
A: a) C 4 silica gels are used for the separation of hydrophobic substances in reversed phase…
Q: When an equilibrium step-growth polymerization is 99% complete, what fraction of the reaction…
A: Step Growth Polymerization: These are a type of polymerization reaction where step wise, first…
Q: Describe in brief about chemical doping and photo doping with respect to the above images?
A: Answer (a)- In case of photo doping , the ground state energy of HOMO and LUMO is quite similar in…
Q: Give some of the application of Coloumetry, Potentiometey, Electrogravimetry and Voltammetry in…
A:
Q: What are the different tetrabasic forms of EDTA? Describe their individual reactivities.
A: The structure of EDTA: EDTA (Ethylenediaminetetraacetic acid) is an amino polycarboxylic acid. The…
Q: Generally, anion exchange resins are negatively charged. Is it true or fasle?
A: This statement is false.
Q: What is cross linking, give how does it effect recycling ability and strength of a polymer,
A: This is a question from polymer chemistry.
Q: ZnO is a non-stoichiometric compound with excess cation interstitials. Write down the defect…
A: Given: ZnO is a non-stoichiometric compound with excess cation interstitials.
Q: 5. Surface excess of the compounds that have surface activity is: 7,-0 b) l'₁ 0 d) r>0 only above…
A: The solution is given below -
Q: and sheets of thermoplastic polymers. Elucidate the po giving TWO (2) suitable examples. Polymers…
A: polymers used in the production of films and sheets: Polyethylene, poly propylene and polyester.…
Q: escribe the difference between the Resistance and Resistivity. (2) Wh= iton and Dolaron2 Explain in…
A:
Q: True or False Leaching of PbCl₂ is ensured when known solution of Group I cations stays hot.
A: Please see explanation.
Q: 1) Phosphorus is diffused into P-Si with doping of 107 cm at T=1000 C for 1 hour by solid solubility…
A:
Q: 3. There is a class of polyesters that have the general structure shown below. . For example, in…
A: The equation which relates the number average molecular weight and glass transition temperature is…
Q: Describe the injection moulding process and distinguish between the injection moulding of TP and TS…
A: Injection moulding process is a method in which plastic materials are injected and are heated or…
Q: 1. What are the practical implications of alloying in carbon and alloy steels?
A: “Since there are multiple questions and it is not mentioned that which one has to be solved so I am…
Q: 1. The surface of silica gel has a structure shown in the diagram below : ОН OH ОН -0- Si - 0- Si-…
A: As given in the question; let us draw the plate before putting into the solvent (acetone) chamber:…
Q: (a). Give THREE (3) distinct features of chemisorptions which are not found in physisorptions. (b).…
A: Two questions based on adsorption, which are to be accomplished.
Q: You have 3 compounds (A, B, C) in your samples. Their polarity A > B > C. You want to separate these…
A: In HPLC technique, the separation of components on basis of polarity, size, charge takes place. The…
Q: DESCRIBE THE PROCEDURE OF d) 600 mL of 3.00% (w/v) aqueous BaCl2from a 0.400 M BaCl2solution.
A: (d) Given - 0.400 M BaCl2 Solution. It means , it has 0.400 moles of BaCl2 in one liter Solution ,…
Q: With reference to the polymerisation mechanisms explain why the polydispersities of the two samples…
A: Polydispersity index is defined as the ratio of weight average molecular mass and number average…
Q: d) By using the data provided below, calculate the PillingBedworth ratio for the nickel (Ni) –…
A: D) Given: Atomic mass of nickel = 58.7 g.mol-1 Density of nickel = 8.91 Mg.m-3 Molecular mass of…
Q: What is the best procedure for phosphorus extraction from biochar by organic acids?
A: Biochar is defined as charcoal generated by biomass pyrolysis, however is used as a soil improver…
Q: Dis cussion:- Ql:- write the chemical structung of EDTA? Qz:- why you measure of the water hardnes,…
A:
Q: 3. If we want to analyze Mg+2 ion, give an example of ion exchange resin carier, spacer and…
A: Ion-exchange chromatography is an important analytical technique where the ionic compounds are…
Q: Consider the following series of poly(phenylene oxide) polymers A–D, and their glass transition…
A: The estimation of Tg depends on the versatility of the polymer chain - the more stable the chain,…
Q: 3.) At room temperature the electrical conductivity of PbTe is 500 (Q-m)1 whereas the electron and…
A: Given, Electrical conductivity of PbTe= 500 / ohm m Electron mobility = 0.16 m2/V.s Hole mobility=…
Q: What are possible sources of error that may occur when performing a cyclic voltammetry experiment?…
A: Cyclic Voltammetry is a method/technique which analyses the transfer of electrons in a reaction…
Q: Compare the column material of GC and LC in terms of the “functional groups” taking place on the…
A: In GC there are two type of coloumn.packed coloumn And capillary Coloumn. In gas liquid…
Q: Which of the following may have caused the formation of bands of the components? (base on the…
A: It is asked in the question to answer for which reason the formation of bands of the components…
Q: a. The structure of a standard C4 group chemically bonded to a silica surface through a silyl ether…
A: SOLUTION: Step 1: The most commonly used column in silica based reverse stationary phase is…
Q: The K2S208 product may be contaminated with K2SO4 or KHSO4. Suggest a method for determining the…
A: PREPARATION OF K2S2O8: The preparation reaction of potassium peroxydisulfate is takes place with the…
Q: Why are adsorbate particles attracted and retained on the surface ofadsorbent?
A: Adsorption is mainly a consequence of surface energy. Generally, the surface particles which can be…
Q: Assuming that the density of silica gel is 2.65 g cm-3 and that the silica particle are spherical…
A:
Q: When plotted according to the linear form of the BET equation, data for the adsorption of N2 on…
A:
Step by step
Solved in 2 steps with 1 images
- Si sample of unknown doping, Hall measurement has been made and thefollowing information obtained: W = 0.05 cm, A = 1.6 x 10-3 cm2, I = 2.5 mA, and the magnetic field is 30 nT (1T = 10^-4 Wb/cm2). If a Hall voltage of +10 mV is measured, find the Hall coefficient, conductivity type, majority carrier concentration, resistivity, and mobility of the semiconductor sample. Plz, don't answer who don't know exactly.A device to understand how iron behaves at high temperatureswe want to design. This device (with 1% accuracy) allows the change in volume (heating) of a 1cm 3 iron cube.the resulting polymorphic transformation) must be able to feel. HMK structure in iron 911 0 C and latticeparameter 0.2863 nm. At 913 0 C, it has YMK structure and its lattice parameter is 0.3591 nm. Of measuring instrumentDetermine the accuracy tolerance it needs (i.e. at least how many cm 3 to detect a changemust). It is necessary to use at least 6 digits after the comma in this question. Hint: YMK first andFor HMK, the volume of an atom is found and then, using the number of atoms in each structure, the ironThe question can be started by finding the different volumes.The given polymer X is composed of A (Mw: 1×104, 1 mole) and B (Mw: 1×105, 1 mole). Calculate Mn andMw of polymer X, respectively. Calculate the polydispersity index
- Zinc is to be used as an internal standard for the polarographic analysis of thallium. A standard solution containing twice the concentration of zinc as Thallium has a diffusion current of 1.89 µA for Ti and 3.50 µA for Zn. A 10.0g alloy was dissolved in 500 mL, 25 mL of this solution was mixed with 25 mL of 1.0 x 10-3 M Zn 2+ solution. The diffusion currents of this final solution are 18.2µA for Tl+ and 14.5µA for Zn+. Calculate % Ti in the sample analysedWhich are true for polarography? I Polarography is amperometry conducted with a dropping Hg electrode. II The diffusion current in the plateau region of the polarographic wave is proportional to the concentration of the analyte and is used for quantitative analysis. III The half-wave potential for maximum current is characteristic of a given analyte in a given medium and can be used for qualitative analysis for the analyte. IV Fresh Hg drops give reproducible results. V Polarography is used to primarily to study oxidations Hg may reduce when studying reductions. A.I, III, and IV B. II, III, and V C. I and V D. III, IV, and V E. II, III, and IV(a) A silicon sample maintained at T = 300 K is uniformly doped with Nd = 1016cm-3 donors. Calculate the resistivity of the sample.
- At room temperature (i.e., 300 K), a semiconductor made of gallium arsenide (GaAs) has an intrinsic electron concentration (ni) of 1.8×10^6 cm^-3 , an electron mobility (μe) of 8500 cm^2 V^1 s^-1 , and a hole mobility (μh) of 400 cm^2 V^-1 s^-1 . \ (a) Calculate the intrinsic electric conductivity and resistivity of GaAs at 300 K. (b) When GaAs is doped with an ionized donor concentration of 10^15 cm^-3 , where is the Fermi level? Calculate the electric conductivity of the doped GaAs. (c) If the semiconductor sample discussed in (b) is further doped with an ionized acceptor concentration of 9×10^14 cm^-3 , what is the free hole concentration and electric conductivity of the sample?(d) By using the data provided below, calculate the PillingBedworth ratio for the nickel (Ni) – nickel oxide (NiO) system and determine whether NiO is protective against corrosion. Atomic mass of nickel = 58.7 g.mol-1 Density of nickel = 8.91 Mg.m-3 Molecular mass of nickel oxide = 74.7 g.mol-1 Density of nickel oxide = 6.67 Mg.m-3 (e) A stainless steel pressure vessel that has fracture toughness, K1C, of 197 MN.m-3/2 is going to be exposed to a stress of 398 MN.m-2 . By using this information explain how designers can determine the thickness of the vessel so that catastrophic failure can be avoided.A solution of altura red of concentration 307 ppm gives an absorbance of 0.616. What concentration is a solution of allura red which gives an absorbance reading of 0.261? The same cell (cuvette) with a path length of 1.000 cm is used for both readings. Report your answer to the nearest whole number without units? Hint: A=abc, where c can have any concentration units. dont provide handwriten solution
- We apply a voltage of 10 V to Fcc an aluminum wire 2 mm diameter and 20 m long , if 10 % of the valence electrons carry the electrical charge , the parameter of cell α = 0. 4049 nm , electrical conductivity σ = 3.77 ×105 cm-1. Ω-1. , calculate the average drift velocity of the electrons in m/secwrite a summary of each of the techniques for measuring vacancyconcentrations, noted therein. (1) Measurements of the quenched-in residual electricalresistivity of aluminium rapidly cooled from temperatures be-low about 800 K with initial quenching rates of 2 × 106 K s−1give the enthalpy of formation of monovacancies H F1V =(0.65 ± 0.01) eV.(2) Comparison of the quenching data with high-temperature differential-dilatometry data gives the monova-cancy formation entropy SF1V = (0.76 ± 0.4)kB (kB =Boltzmann’s constant) and the low-temperature resistivity perunit concentration of vacancies ρ1V = (1.9 ± 0.1) μm.(3) The binding enthalpy of divacancies in Al is H B2V =(0.17 5 ± 0.02 5) eV. This is in agreement with earlier ex-perimental determinations by Doyama and Koehler 48) and byLevy et al. 49, 50) but in marked contrast to the claim of Carlinget al., 23) based on computations with the generalized gradi-ent approximation, that in Al H B2V is zero or even negativeand therefore the…In an analysis of chromium in steel containing 1.76% Cr. 0.5000 g of that steel is weighed and dissolved in acid, whereupon the Cr is oxidized to Cr2O72- (dichromate), and blunt to a volume of 250 mL. A 10 mL aliquot of this solution is diluted with water and acid to a final volume of 100 mL. The resulting solution shows a transmittance of 41.7% in a 1 cm pathlength cell. When a 0.7500 g sample of unknown steel is dissolved in acid, oxidized, and diluted to 250 mL, the resulting solution exhibits a transmittance of 61.3% under identical experimental conditions. What is the percentage of Cr in the steel?
