Si sample of unknown doping, Hall measurement has been made and the following information obtained: W = 0.05 cm, A = 1.6 x 10-3 cm2, I = 2.5 mA, and the magnetic field is 30 nT (1T = 10^-4 Wb/cm2). If a Hall voltage of +10 mV is measured,

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter2: Electrical Components And Circuits

Section: Chapter Questions

Problem 2.1QAP

See similar textbooks

Related questions

Q: When a certain electrolytic cell was filled with 0.1 M KC1, it has resistance of 85 ohms at 25 °C.…

A: Electrochemistry is the branch of chemistry that deals with the flow of electrons in the solution…

Q: iv-ionization coefficients a, y are function of a-applied voltage b-pressure and temperature…

A: Ans. iv) option d is right. ratio of electric field to pressure v) option b is right Kdn vi)…

Q: In a certain conductivity cell, the resistance of a 0.01 M KCl solution is 150 W. The known molar…

A: Interpretation - To determine the cell constant (Kcell unit is cm-1) when in a certain conductivity…

Q: Calculate the isosteric enthalpy of adsorption from the following results which were obtained for…

Q: An unknown amount of copper(II) ions produces a faradic current of 12.3 A on a normal pulse…

Q: A compound Y (150.0 g/mol) in a 1.00 cm quartz cell has an extinction coefficient (ε) of 23,150 at…

A: Answer = 509.12 Complete solution is given in next step.

Q: 1.A compound Y (150.0 g/mol) in a 1.00 cm quartz cell has an extinction coefficient (ε) of 23,150 at…

A: Answer to Question No:1 The energy of a photon can be calculated by the famous formula- E=hcλwhere,…

Q: Consider a homogeneously doped n-type semiconductor at 300K. The electron concentration is equal to…

Q: The transfer coefficient of a certain electrode in contact with M2+ and M3+ in aqueous solution at…

A: The relation between the current density and the overpotential, when the overpotential is 105 mV or…

Q: What are the main advantages and limitations of the Valencia Linkage Theory?

A: Valencia linkage theory or valence bond theory A theory which explain bonding in chemical compound…

Q: Q1/ The following information is available on the polarization curve of the active- surface TAEFL…

Q: Si is doped with 2x1017 boron (B) atoms/cm³ and 6x1017 phosphorous (P) atoms/cm³. (a) Is this n-type…

A: given concentration of phosphorus = 6 X 1017 concentration of boron = 2 x1017 ni = 1010 cm-3

Q: Spin transistor. a the origin of Polarity of magnetoresistance in graphene interlayer

A: In this question we have to tell that the origine of polarity of Magnetoresistance in graphene…

Q: The maximum electric field in a reverse-biased semiconductor p-n junction at T-300K is to be…

Q: The conductivity of a 0.05M solution of acetic acid at 18⁰C is 4.4×10-4 (ohms)-1cm-1. Limiting molar…

Q: A solution containing 8.75 ppm KMnO4 has a transmittance of 0.743 in a 1.00 cm cell at 520 nm.…

Q: Calculate the effect that increasing the overpotential from 0.50 V to 0.60 V has on the current…

A: From Butler-Volmer equation, at large overpotential, the ratio of current densities (j1/j2) at two…

Q: escribe the difference between the Resistance and Resistivity. (2) Wh= iton and Dolaron2 Explain in…

Q: .A conductance cell filled with 0.01 M solution of an electrolyte offered a resistance of 2300 ohms.…

A: To solve this problem first we have to calculate the specific conductance (K) and then we will…

Q: The given polymer X is composed of A (Mw: 1×104 , 1 mole) and B (Mw: 1×105 , 1 mole). Calculate Mn…

A: The number average molecular weight of the polymer, Mn = n1M1+n2M2n1+n2 The weight average molecular…

Q: 1) Phosphorus is diffused into P-Si with doping of 107 cm at T=1000 C for 1 hour by solid solubility…

Q: It is desired to chrome a cubic metal piece with a 10 cm edge with a chromium layer (d = 7.2 g / ml)…

A: A numerical problem based on electrolysis that is to be accomplished.

Q: Q3 a) Describe the mechanism of electrical conduction inside a semiconductor? b) Calculate the…

A: Answer..

Q: (f) Why alternating current is used for conductometric measurements?

A: Conductometric titrations :- It is a qualitative method used for determining the concentration of an…

Q: KUESTION: 1 Silicon at T=300K contains a acceptor impurity concentration at Na=1016 cm-3. Determine…

A: Given:- Let the donor concentration = ND cm-3 Acceptor concentration NA =…

Q: The resistance of decinormal solution of a salt occupying a volume between two platinum electrodes…

A: Given data : Normality =0.1N (Decinormal solution) Resistance = 32 ohms Area= 5.4 cm2 Length= 1.80…

Q: What are the maximum atomic and weight percentages of Cu that can be added to Au without exceeding a…

Q: What are the different tetrabasic forms of EDTA?

A: Ethylenediamine tetraacetic acid (EDTA) is a polyprotic acid containing four carboxylic acid groups…

Q: Determine the diffraction angle of a polycrystalline material alpha-Fe BCC at (211) plane with…

Q: (a) A silicon sample maintained at T = 300 K is uniformly doped with Nd = 1016cm-3 donors. Calculate…

Q: The forward-bias voltage (V) required to maintain a PN diode current (I) is a function of the…

Q: Two parallel gray planes have emissivities of 0.8 and 0.7 and are maintained at 800°C and 1500°C.…

Q: A cell containing asolution of potassium chloride with a concentration of 0.1mol dm^-3 and has a…

A: Given data,Concentration of KCl(CKCl)=0.1mol/dm3Molar conductivity of…

Q: 14. The transport numbers for HCI at infinite dilution are estimated to be t=0.8210 and t 0.1790 and…

Q: Items 1 to 5: What is the log10 MW of the following bands? 1. Band 2 А. 0.943 B. 0.963 C. 0.973 D.…

A: 1) log10 MW of band 2 Correct option is C log (9.40) = 0.973 2) log10 MW of band 4 Correct…

Q: 3.) At room temperature the electrical conductivity of PbTe is 500 (Q-m)1 whereas the electron and…

A: Given, Electrical conductivity of PbTe= 500 / ohm m Electron mobility = 0.16 m2/V.s Hole mobility=…

Q: At room temperature (i.e., 300 K), a semiconductor made of gallium arsenide (GaAs) has an intrinsic…

A: The electrical conductivity and resistivity can be expressed as follows-

Q: 1. 1/3 of the incident light flux passes through a layer of aqueous solution with a thickness of 4.2…

A: The amount of light that is absorbed by the solution and reflected depends on the concentration of…

Q: The diffusion current in a polarogram for reduction of Cd2+at a mercury electrode is 12.0 mA. If the…

A: The time is given in minutes. Firstly, convert the minutes into seconds by multiplying the time by…

Q: When a rotating disk electrode (RDE) is held at a high enough potential, the rate of the reaction is…

Q: Compute the resistivity of aluminum wire 5 mm in diameter and 5 m long. 4 07.6 x 10^-3 O 6.7 x 10^-5…

A: \Given that : Diameter = 5mm = 5×10-3 m Length = 5 m

Q: HW Q.1 The chemical analysis of formation water as follow; concentration (ppm) lon Na 14,000 12,000…

A: The chemical analysis of formation water is given The room temperature = 75°F To determine:- The…

Q: 3.) At room temperature the electrical conductivity of PbTe is 500 (N-m)1 whereas the electror and…

A: According to question Electrical conductivity is 500 /ohm m Electron mobility is 0.16m²/V s Hole…

Q: Carbon is allowed to diffuse through a steel plate 15 mm thick. The concentrations of car- bon at…

A: We have find out the temperature at which the diffusion flux is 1.43 x 10-⁹ kg/m².s.

Concept explainers

UV Visible Spectroscopy

Spectroscopy refers to the absorption or emission of light or other radiations by matter. When a substance or chemical absorbs light or radiation, they reach an excited state followed by de-excitation or emission of the light or radiation forming distinct spectra. UV-visible spectroscopy or ultraviolet-visible refers to the absorption and emission in the ultraviolet and visible regions of the electromagnetic spectrum.

Question

Si sample of unknown doping, Hall measurement has been made and the
following information obtained: W = 0.05 cm, A = 1.6 x 10-3 cm2, I = 2.5 mA, and the magnetic field is 30 nT (1T = 10^-4 Wb/cm2). If a Hall voltage of +10 mV is measured, find the Hall coefficient, conductivity type, majority carrier concentration, resistivity, and mobility of the semiconductor sample.

Plz, don't answer who don't know exactly.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

(a) A silicon sample maintained at T = 300 K is uniformly doped with Nd = 1016cm-3 donors. Calculate the resistivity of the sample.
Zinc is to be used as an internal standard for the polarographic analysis of thallium. A standard solution containing twice the concentration of zinc as Thallium has a diffusion current of 1.89 µA for Ti and 3.50 µA for Zn. A 10.0g alloy was dissolved in 500 mL, 25 mL of this solution was mixed with 25 mL of 1.0 x 10-3 M Zn 2+ solution. The diffusion currents of this final solution are 18.2µA for Tl+ and 14.5µA for Zn+. Calculate % Ti in the sample analysed
At room temperature (i.e., 300 K), a semiconductor made of gallium arsenide (GaAs) has an intrinsic electron concentration (ni) of 1.8×10^6 cm^-3 , an electron mobility (μe) of 8500 cm^2 V^1 s^-1 , and a hole mobility (μh) of 400 cm^2 V^-1 s^-1 . \ (a) Calculate the intrinsic electric conductivity and resistivity of GaAs at 300 K. (b) When GaAs is doped with an ionized donor concentration of 10^15 cm^-3 , where is the Fermi level? Calculate the electric conductivity of the doped GaAs. (c) If the semiconductor sample discussed in (b) is further doped with an ionized acceptor concentration of 9×10^14 cm^-3 , what is the free hole concentration and electric conductivity of the sample?
Knowing that an electroplating industry wants to coat a steel sheet with a layer of metallic Cu by an electrodeposition process, what is the time to deposit a 50 μm layer on a 10 cm2 plate applying a current density of 30 mA /cm2 if process efficiency is 75%.
We apply a voltage of 10 V to Fcc an aluminum wire 2 mm diameter and 20 m long , if 10 % of the valence electrons carry the electrical charge , the parameter of cell α = 0. 4049 nm , electrical conductivity σ = 3.77 ×105 cm-1. Ω-1. , calculate the average drift velocity of the electrons in m/sec
An atomic beam is designed to function with (a) cadmium, (b) mercury. The source is an oven maintained at 380K with a small slit of dimensions 1.0cm x 1.0 x 10-3cm. The vapor pressure of cadmium is 0.13 Pa nd that of mercury is 12 Pa at this temperature. What is the atomic current (the number of atoms per second) in the beams?
Please assist with the following sub questions of question 1. a) The conductivity of a 0.05M solution of acetic acid at 18⁰C is 4.4×10-4 (ohms)-1cm-1. Limiting molar conductivity of acetic acid at the same temperature is 387 (Ohms)-1cm². Calculate the dissociation constant (Ka) of acetic acid? b) The resistivity of aluminum is 2.824×10-8 ohms.m. Calculate the potential drop across a piece of aluminum wire that is 2.0 mm in diameter and 1.00 m long. Assume current is 1.25 A. C) Calculate the conductance and conductivity of a metal if the resistivity of the metal is 2.824×10-8 ohms.m, with resistance of 9.0×10-3 ohms when current is 1.25 A.
The classical dissociation constant of propionic acid, C2H5CO2H, is 1.34 x10-5 moldm-3 at 250C and the limiting molar conductivities at zero concentration of hydrogen and propionate ions are 349.8 and 35.8 ohm-1 cm2 mol-1 respectively. Calculation of the resistivity of 0.100 M solution of propionic acid.
The given polymer X is composed of A (Mw: 1×104, 1 mole) and B (Mw: 1×105, 1 mole). Calculate Mn andMw of polymer X, respectively. Calculate the polydispersity index
If you wish to decrease the amount of current in a resistor from 240mA to 180mA by changing the 24V source, what should be the new voltage setting be?
What are the advantages of a dropping-mercury electrode in polarography? Why is polarography used mainly to study reductions rather than oxidations?
2. (d) Describe three of the functions of the matrix in fibrereinforced composites. (e) With the aid of sketches compare and contrast the fatigue fracture appearance between an alloy that failed at a low fatigue load and one that failed at a high fatigue load. (f) Propose and briefly describe one non-destructive method that can be used to detect small cracks on the surface of a metallic alloy .