4. A venturi meter with a 10.16 cm throat is installed in a 15.24 cm pipe which is inclined upward at an angle of 45 degrees to the horizontal. If the distance between the pressure tape along the pipe is 1.5 m, the differential pressure is 70kPa, and the water temperature is 70°C, what is the discharge of water in m³/sec?. Assume coefficient of 0.985.

4. A venturi meter with a 10.16 cm throat is installed in a 15.24 cm pipe which is inclined upward at an angle of 45 degrees to the horizontal. If the distance between the pressure tape along the pipe is 1.5 m, the differential pressure is 70kPa, and the water temperature is 70°C, what is the discharge of water in m³/sec?. Assume coefficient of 0.985.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A venturimeter with a 10.16cm throat is installed in a 15.24cm pipe which is inclined upward at an angle of 45 degrees to the horizontal. If the distance between pressure taps along the pipe is 1.5, the difference in pressure is 70 kPa, and the water temperature is 70oC, what is the discharge of water in m3/sec? Assume coefficient of 0.985.
SAMPLE PROBLEMS #3 A venturi meter with a 10.16 cm throat is installed in a 15.24 cm pipe which is inclined upward at an angle of 45 degrees to the horizontal. If the distance between pressure tape along the pipe is 1.5 m, the differential pressure is 70 kPa, and the water temperature is 70°C, what is the discharge of water in m'/sec? Assume coefficient of 0.985.
Water is flowing at the rate of 1.676 m/s in a 3.068 inches’ diameter horizontal pipe at apressure p1 of 68.9 kPa. It then passes to a pipe having an inside diameter of 2.067 inch. Thedensity of the water is 998 kg/m3.a) Calculate the new pressure p2 in the 2.067inch pipe. Assume no friction losses.b) If the piping is vertical and the flow is upward, calculate the new pressure p2. The pressure tap for p2 is 0.457 m above the tap for p1.c) Compare and discuss your answers in 2 (a) and 2(b).
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
A pump has a 100 mm diameter suction pipe and a 75 mm discharge pipe The capacity is 15 L/s of water A water- mercury manometer is installed in the inlet which reflects a vacuum pressure of 198mm of Hg The mercury level on the suction side is 100 mm below the pipe centerline. The pressure gauge 200 mm above the pump iniet recorded a pressure of 0.95 bar. The measured input power was 3.2 kW Find the efficiency of the pump Select the correct response(s) 75.12 % 60 42 % 59 01 % 80.43 %
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 112 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.92 and sp. gr of oil = 0.8 %3D (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in m) = Velocity of flow (unit in m/s) =
liquid pentane with relative density 0.62, 20 °c as shown in the figure at temperature, the geyç pressure is 0.2 atm dollars a cast iron (0.2 m odiameter cast iron)) it flows through the pipe.Marked as full pipe output it can be considered as the principal atmospheric pressure at the point at which it is. The total pipe length in the system is 45 m.5 kW in the system there is a pump that works with 92% efficiency in its power. Liquid since the volumetric flow rate of pentane is 0.05 m2 / s, with the tank calculate the height difference botween the pipe output. Data: * Friction loss at the pump is negligible. Gryc Atark purmp
A venturi meter of 20 mm throat diameter is used to measure. The velocity of water in a horizontal pipe of 40 mm diameter. If the pressure difference between the pipe and the throat sections is found to be 30 KPa then, neglecting frictional losses, the flow velocity is?
A pipe of diameter 18 cm, is used to pump the water to the house in the Hamra hill at the height of 50 m than the ground. The discharge at the end of the pipe is 220 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 35 N/cm². Find the following: (i) The velocity head at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id....) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe (unit in m) ,
A water supplying pipe of diameter 14 cm, is used to pump the water to the house in the Tanuf hill at the height of 60 m above the ground. The flowrate at the end of the pipe is 180 lit/s. The pressure gauge is connected at the inlet of the pipe in the ground and measured as 35.5 N/cm2. Find the following: (i) The kinetic energy per unit weight at the entry of pipe (in m) (ii) Pressure head at the inlet (in m) (iii) Total available energy per unit weight of the water at the pipe entry (unit in m)
Find the difference in pressure head and velocity of flow of an ail through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 116 mm. Take co-efficient of the pitot tube ("L shaped measuring instrument) as 0.97 and sp. gr of ail = 0.85 (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr)%3D
A pitot static tube is used to measure the velocity of water in a pipeline. If the mercury manometer attached to it shows a reading of 0.17 m, calculate the water velocity in the pipe. Assume coefficient of velocity as 0.98.