6-58 Water is flowing into and discharging from a pipe U- section as shown in Fig. P6-58. At flange (1), the total absolute pressure is 200 kPa, and 30 kg/s flows into the pipe. At flange (2), the total pressure is 150 kPa. At location (3), 8 kg/s of water discharges to the atmosphere, which is at 100 kPa. Determine the total x- and z-forces at the two flanges connecting the pipe. Discuss the significance of gravity force for this problem. Take the momentum-flux correction factor to be 1.03. 8 kg/s -3 ст 22 kg/s- J10 cm 30 kg/s D 5 cm

6-58 Water is flowing into and discharging from a pipe U- section as shown in Fig. P6-58. At flange (1), the total absolute pressure is 200 kPa, and 30 kg/s flows into the pipe. At flange (2), the total pressure is 150 kPa. At location (3), 8 kg/s of water discharges to the atmosphere, which is at 100 kPa. Determine the total x- and z-forces at the two flanges connecting the pipe. Discuss the significance of gravity force for this problem. Take the momentum-flux correction factor to be 1.03. 8 kg/s -3 ст 22 kg/s- J10 cm 30 kg/s D 5 cm

Name: 6-58 Water is flowing into and discharging from a pipe U-section as s
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 6-58 Water is flowing into and discharging from a pipe U-section as shown in Fig. P6-58. At flange (1), the totalabsolute pressure is 200 kPa, and 30 kg/s flows into the pipe.At flange (2), the total pressure is 150 kPa. At location (3), 8kg/s of wa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reducing elbow is used to deflect water flowrate at a rate of 1920 g/s in a horizontal pipe downward by an angle theta = 43 from the flow of direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow at the inlet is 6.5 cm and at the exit is 1.5cm. The elevation difference between the centers of the exit and the inlet is 22cm . The mass of the elbow and the water is 61.5 kg. Determine the anchoring force needed to hold the elbow in place
A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
Orange juice is flowing through a horizontal U-type reducing bend at a rate of 36kg/s. The cross-sectional area, gage pressure, and velocity are 168cm^2, 57.5 kPa, and 2.10 m/s at the inlet, and 80cm^2, 50kPa, and 4.37 m/s at the outlet. Calculate the force applied to the reducing bend by the orange juice in the horizontal direction
A cylindrical tank is being filled with water flowing with constant velocity V1 through a tap (Tap 1) that has an opening of diameter D1. The tank is initially empty and contains a tap (Tap 2) placed H1 m above the bottom of the tank that drains waterat a velocity of ? = √2?h. Assuming flow through Tap 2 starts the moment Tank 1 2height reaches H1 m, write the differential equation governing the change of water level inside the tank with time (?h =? );??i) Before water level reaches H1.ii) After water level reaches H1 up until the tank is full.Do NOT attempt to solve the differential equations!Just drive the differential equations and write the boundaries of the definite integrals.
In this situation, a 90 degree elbow pipe is used to direct water flow in an upwards direction, at a rate of 40 kg/s. Here the diameter of the elbow is 10cm. The water is discharged into the atmosphere and the pressure at exit is at the local atmospheric pressure. Additionally the elevation difference between the centers of exit and inlet of the bend is 50cm. Here, the weight of the elbow pipe and the water is neglible, and the momentum-flux correction factor is 1.03 at both the oulet and inlet. How would I determine the gage pressure at the center of the inlet of the elbow? How much anchoring force would be needed to hole the elbow in place. Any help would be greatly appreciated :)
. It has been assumed that the velocity of the jet is uniform over its cross-section. plow is the momentum of the jet affected if this is not the case? Consider a jet with a cross-sectional area (4) in which the velocity is 0.5vo over half of the area and 1.5vo over the other half. The discharge is the same as if the velocity were vo over the whole, namely: W = voA. Show that the delivery rate of momentum in the jet is 1.25Wvo, i.e., 25% greater than the uniform velocity over the cross-section.
A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.
A pump draws water from a 20 cm diam suction pipe and discharges through a15 cm diam pipe in which the velocity is 3.60 m/s. The pressure is – 34. 465 kPaat A in the suction pipe. The 15 cm diam pipe discharges horizontally into air atC. To what height h above B can the water be raised if B is 1.8 m. above A and20 hp is delivered to the pump? Assume that the pump operates at 80 %efficiency and that the frictional loss in the pipe between A and C is 3 m. Determine the inclination angle at point C for the water stream to reach a range of 10 m. Calculate the maximum height that the water can go from the selected datum plane.
Consider water flow through a horizontal, short garden hose at a rate of 30 kg/min. The velocity at the inlet is 1.3 m/s and that at the outlet is 11.75 m/s. The hose makes a 180° turn before the water is discharged. Disregard the weight of the hose and water. Taking the momentum-flux correction factor to be 1.08 at both the inlet and the outlet, the anchoring force (in N; hint: the answer is a negative number) required to hold the hose in place is ?
Water enters a centrifugal pump axially at atmospheric pressure at a rate of 0.10 m3/s and at a velocity of 6 m/s and leaves in the normal direction along the pump casing, as shown in the figure. Determine the force acting on the shaft (which is also the force acting on the bearing of the shaft) in the axial direction
Determine the shear stress at the wall of 1/16 inch diameter horizontal pipewhen water (μ=0.857 x 10-3 N.s/m2, ρ=1000 kg/m3 ) flows through it with a velocity of 0.30 m/s.[Ans: 1.348 N/m2 ]