78) Technician A says when a driving clutch is released, the drive discs drive the driven discs splined to the drum.Technician B says when a driving clutch is released, the drive discs rotate with the driven discs splined to thedrum. Which technician is correct?O Technician AO Technician BBoth technicians A andBNeither technician Aпог В

Given Clutch assembly To find How the assembly works

78) Technician A says when a driving clutch is released, the drive discs drive the driven discs splined to the drum. Technician B says when a driving clutch is released, the drive dises rotate with the driven discs splined to the drum. Which technician is correct? O Technician A O Technician B O Both technicians A and в O Neither technician A nor B

78) Technician A says when a driving clutch is released, the drive discs drive the driven discs splined to the drum. Technician B says when a driving clutch is released, the drive dises rotate with the driven discs splined to the drum. Which technician is correct? O Technician A O Technician B O Both technicians A and в O Neither technician A nor B

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter37: Clutches

Section: Chapter Questions

Problem 1ASRQ: Technician A says that clutch slippage is most notice-able in higher gears. Technician B says that...

See similar textbooks

Similar questions

A car jumps out of gear into neutral, particularly when decelerating or going down hills: Technician A checks the shift lever and external gearshift linkage first. Technician B says that the clutch pilot bearing could be the problem. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
While discussing a clutch alignment tool. Technician A says that the part of the tool that fits into the clutch plate must have a slightly larger OD (outside diameter) than the bore in the disc. Technician B says that the OD of the part of the tool that goes into the pilot must be slightly smaller than the ID (inside diameter) of the pilot bushing. Who is correct? Technician A Both A and B Technician B Neither A nor B
Technician A says that if the shift for all forward gears is delayed, a slipping forward clutch is normally indicated. Technician B says that a bad forward clutch is indicated when there is a slip when the transmission shifts into any forward gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Technician A says that when a car is moving straight ahead, all differential gears rotate as a unit. Technician B says that when a car is turning a corner, the inside differential side gear rotates slowly on the pinion, causing the outside side gear to rotate faster. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Which of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplate
While inspecting the timing gears of an engine: Technician A says a gear with cracks, spalling, or excessive wear on the tooth surface indicates improper gear backlash. Technician B says the diameter of many of the engines timing gears and sprockets should be measured with the drive chain wrapped around the individual gears. Who is correct? Technician A Technician B Both A and B Neither A nor B
While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?
Pinion gear-to-flywheel ring gear clearance is being discussed: Technician A says that if there is too much clearance, there will be a high pitch while the engine cranks. Technician B says that if there is too little clearance, there will be a high pitch noise after the engine is started. Who is correct? Technician A Technician B Both A and B Neither A nor B
While discussing ways to determine if a pilot bushing is faulty: Technician A says that if it operated quietly, it does not need to be replaced. Technician B says that a careful inspection of the transmissions input shaft can determine the condition of the pilot bushing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
During a test drive, a noise that appears to be transmission related disappears when the driver brings the vehicle to a stop and disengages the clutch with the engine at idle. Technician A says that the noise may be caused by an internal transmission problem. Technician B says that the problem may be something interfering with the flywheel or pressure plate. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
Technician A says that the transmission rear seal at the driveline is particularly prone to leakage. When Technician B pushes up and down on the transmission, he says that the mounts require replacement because the case moves up and down. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B
While checking the engine and transmission mounts on a FWD car: Technician A says that any engine movement may change the effective length of the shift and throttle cables and therefore may affect the engagement of the gears. Technician B says that delayed or missed shifts are caused by hydraulic prob lems, not linkage or control problems. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor B