A sample of Coomassie Blue is prepared by mixing 20 µL of stock with 280 µL of 0.1 M Tris into a round-bottom microplate. Calculate the concentration of the stock solution of Coomassie in ug/ml. The sample had a resulting A550 0.530 and the extinction coefficient for Coomassie Blue at 550 nm is 0.0168 ml/(cm"ug).

A sample of Coomassie Blue is prepared by mixing 20 µL of stock with 280 µL of 0.1 M Tris into a round-bottom microplate. Calculate the concentration of the stock solution of Coomassie in ug/ml. The sample had a resulting A550 0.530 and the extinction coefficient for Coomassie Blue at 550 nm is 0.0168 ml/(cm"ug).

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter15: Electrophoresis And Other Separation Methods

Section: Chapter Questions

Problem 5P

See similar textbooks

Similar questions

The detecton limits reported for Al with ICP-AES and GF-AAS are 2 ppb and 5 picograms, respectivly. If we assume that a 20 microliter sample volume is used for the GF-AAS determination, which method has the lower detection limit? (1 picogram = 10-12 gram.)
A standard curve for glucose analysis was prepared.The slope (m) was found to be 1.341 while the y-intercept (b) was -0.333. Calculate the concentration (x) of glucose having an absorbance (y) of 0.151. 0.067 0.361 0.858 0.136
A spectrophotometric method for the quantitative analysis of Pb2+ in blood has a normal calibration curve for which Sstd=(0.296 ppb−1)×Cstd+0.003. What is the concentration of Pb2+ in a sample of blood if Ssamp is 0.397?
A graphite furnace atomic absorption spectrophotometer (AAS) was used to determine the arsenic (As) concentrations in drinking water. A large set of blank samples yielded an average blank signal of 0.013 and a blank standard deviation of 0.0030. The following data were obtained for a calibration curve. [As] (ppm) 2.0 4.0 6.0 8.0 10.0 Absorbance 0.17 0.28 0.48 0.53 0.72 Using a spreadsheet on an Excell, create a graph of the data using symbols only for the data points. Plot the line on the same graph and include the graph to this question. (a). What is the sensitivity of the method? (b). Calculate the LOD and LOQ for As. (c). A sample of water yielded an absorbance of 0.43. What is the concentration of As in the water?
Concentration=2.5 X 10^3 μM OD400nm=0.859 1cm cuvette is used what is the extinction coefficient (μM^-1 cm^-1)
As part of an analytical chemistry laboratory course, a student measured the Ca2+ content in two water samples, city-supplied drinking water and well-supplied drinking water, using two different analytical methods, flame atomic absorption spectrometry (FAAS) and EDTA complexometric titration. The results of this experiment are given in the table as the mean Ca2+concentration (?¯) and standard deviation (?) in parts per million (ppm). Each sample was measured five times (n=5) by each method. Method City-Supplied Drinking Water (?¯±?x¯±s) Well-Supplied Drinking Water (?¯±?x¯±s) FAAS 57.57±0.68 ppm 64.77±0.70 ppm EDTA titration 58.32±0.96 ppm 65.62±0.97 ppm Method Comparison: For each drinking water sample (city and well), compare the Ca2+ content measured by FAAS and EDTA titration. Calculate the ? value for each sample. Do the methods produce statistically different results at the 95% confidence level when measuring the Ca2+content of the city-supplied drinking water? Do the…
A 0.0200 gram blood sample was decomposed by a microwave digestion technique followed by dilution to 100.0 mL in a volumetric flask. Aliquots of the sample solution were treated with a lead complexing reagent and water as follows: Solution 1: 10.0 ml blood sample + 20.0 mL complexing agent + 30.0 mL H20. Solution 2: 10.0 ml blood sample + 20.0 mL complexing agent + 26.0 mL H20 + 4.00 mL of 78 ppb Pb2+ standard. The resulting solutions were analyzed by UV/Vis at 375 nm. Absorbance for solution 1 = 0.155 and for solution 2 = 0.216. Calculate the concentration of lead (ppb) in the original sample.
1 mL was taken from the sample filtrate and mixed with 13 mL pure water and 4 mL sulfomolybdic acid and 2 mL dilute SnCI2 solution by adding it, and after waiting for 15 minutes, the absorbance of the resulting solutions against pure water was read at 520 nm. if the function of the calibration graph obtained with standard phosphorus solutions of 0.5-2.5 mg/mL is y= 0.245x + 0.107 and the absorbance of the serum sample is 0.342, how many grams of phosphorus is the amount in the sample?
A spectrophotometric method for the quantitative determination of the concentration ofPb2+ in blood yields an Ssamp of 0.133 for a 1 mL sample of blood that has been diluted to 6 mL. A second sample is spiked with 1 µL of a 1467 ppb Pb2+ standard and diluted to 6 mL, yielding an Sspike of 0.491. Determine the concentration of Pb2+ in the original sample of blood.
Effect of dose on adsorption percentage of cadmium onto magnetite (pH 7; adsorbent dose = 0.05, 0.1, 0.5, 0.10, 0.15 g; initial concentration 100 ppm, T = 25°C, 150 rpm, Contact Time = 2 h) performed with ASS instrument. What is the optimal dosage?
Determine the relationship between the observed/apparent value (EX) VERSUS that of the true value (ET) for the quantity being sought by writing either <, >, or = on the space provided Determination of the true concentration (ppm Fe) in a water sample using the iron-phenanthroline method. Dilution factor was not taken into account. EX _____ 1ET
Ben ran through the experiment and found the best-fit line listed below for his standard calibration curve of absorbance vs concentration in M. y = 3214.0x + 0.0076 Ben then prepared a solution that had 5.00 mL 0.002 M iron(III) nitrate in 1 M nitric acid, 3.00 mL 0.002 M potassium thiocyanate, and 2.00 mL DI water. If the absorbance for the solution was 0.436, calculate the equilibrium concentration of iron(III) thiocyanate in the solution. Report your answer in mM with three places after the decimal.