(c) Design a voltage regulator using the circuit in Figure 3. The voltage regulator is to power a car radio at V = 9 V from an automobile battery whose voltage may vary between 11 and 13.6 V. The current in the radio will vary between 0 (off ) to 100 mA (full volume). Iz(min)=0.1 Iz(max). Hint: Find the suitable current limiting resistor and Zener diode. %3D R; Vps Radio Figure 3. Circuit for design

(c) Design a voltage regulator using the circuit in Figure 3. The voltage regulator is to power a car radio at V = 9 V from an automobile battery whose voltage may vary between 11 and 13.6 V. The current in the radio will vary between 0 (off ) to 100 mA (full volume). Iz(min)=0.1 Iz(max). Hint: Find the suitable current limiting resistor and Zener diode. %3D R; Vps Radio Figure 3. Circuit for design

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

a. SketchtheoutputvoanddeterminethedcleveloftheoutputforthenetworkofFig.2.49. Repeat part (a) if the ideal diode is replaced by a silicon diode. Repeat parts (a) and (b) if Vm is increased to 200 V, and compare solutions using Eqs. (2.7) and (2.8).
2. A certain zener diode has a maximum power rating of 300 mW at 40 deg Cand a derating factor of 1.4mW/deg C. Determine the maximum power the zener can dissipate at a temperature of 80 deg C. 3. From the datasheet, a 1N4728A zener diode has a ZZ of 10 0. The datasheet gives VZ = 3.3 V at a test current, IZ, of 76 mA. What is the voltage across the zener terminals when the current is 90 mA? When the current is 45 mA?
Don't copy others work. provide correct solution Question (1)(a) Define homo-structure and hetero-structure devices with appropriate schematic diagram of such structures. (b) Explain the concepts of lattice matched hetero-structure. Sub: Optoelectronics Dept:EEE
Given the schematic below, assume D1 and D2 are silicon with forward voltages of 0.7V. Find the following (with solutions) a) Conditions required wherein none of the diodes are conducting b) If both diodes are not conduction, what is Vo? Express in terms of Vi c) Plot the overall relationship of Vo and Vi in the coordinate system shown below. Remember, you are to plot the transfer characteristics of the circuit.
Exercise 3: In the circuit of figure below, the diode is assumed to be perfect. The transformer secondary has zero resistance and delivers voltage ve(t)= V msin wt. 1. Draw the waveform of vs(t) when the capacitor is disconnected. 2. The capacitor being switched on, we assume that the start of the charge is at time t = 0. a. Give the expression of the current i(t); we will then suppose x(t) = wt b. Determine the angle x1(t) = wt, of the end of conduction of the diode. 3. When the diode has stopped conducting, what is the equivalent circuit in figure below? Write the differential equation governing this circuit. Give its general solution. Deduce the expression of vs(t) for the discharge phase of the capacitor. 4. Write the mathematical condition corresponding to the angle x2(t) = wt2 end of discharge of the capacitor. 5. Deduce the approximate waveform from the filtered voltage Vs(t).
CP3: A Fally controlled single-phase bridge rectifier is supplied from a 50Hz, 230/100 * V transformer It is supplying a highly inductive load of 10Omega resistance. For a firing angle of 45, determine the rectified voltage and the rectified current.
In your own words(not googled) please answer and help me understand the following a. What is a LED? Explain the working of a LED and give at least two applications. b. Why do LEDs need series current-limiting resistors? c. How does LED differ from an ordinary diode? d. What is a photodiode? Explain how it works and give at least two applications. e. What is a/an: i. Tunnel diode ii. Optoisolator iii. Varactor diode iv. Shockley diode
A practical silicon-based solar cell is constructed from a n+ p junction. a. Explain briefly the meaning of the notation n+ ? b. Draw a sketch showing the device structure of this solar cell. c. This cell shows a photocurrent IL = 10.9 A under AM1.5G illumination.If the temperature is 25oC, what is VOC ? Assume that the saturatedcurrent IS = 1×10-9 A.
A crystal diode having internal resistance rf, = 20ohm is used for half-wave rectification. lf the applied voltage v = 50 sin wt and load resistance RL, = 800ohms find: 1. I m, l dc and I rms 2. a.c. power input and dc power output 3. DC output voltage 4. Efficiency of rectification
If the operating voltage of the LED diode given in the circuit in the figure is 2.2V, the operating current is 30mA, and the Vs source voltage is 12V, calculate the value of the R1 resistor connected in series with the diode.
Good day. This is Fundamentals of Electronics Circuits subject. Please do help. No need for solutions
(02) DC Si Diode Circuit. (Course: Electronic Devices and Circuit Theory) What is the minimum value for RL needed to turn Zener diode ON?, And what is the maximum value for RL needed to turn Zener diode is ON? -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.