Plz solve this nowbin 30 min a get a thumb up Consider the tin (Sn)- bismuth (Bi) equilibrium diagram reproduced below. An alloycontaining 10wt% Bi is held at a temperature of 200°CB1300271Liquid250232200B+ Liquida + Liquid150184138.5C100a+B50Sn10 20304050Weight Bismuth60708090Bi(c) What are the proportionn (%) of each phase in the alloy?5. angeadue

Consider the tin (Sn)- bismuth (Bi) equilibrium diagram reproduced below. An alloy containing 10wt% Bi is held at a temperature of 200°C 300 271 Liquid 250 232 200 a + Liquid B+Liquid 150 184 138.5C 100 a+B 50 Sn 10 20 30 40 50 60 70 80 90 Bi Weight Bismuth c) What are the proportions (%) of each phase in the alloy? Temperature, C B.

Consider the tin (Sn)- bismuth (Bi) equilibrium diagram reproduced below. An alloy containing 10wt% Bi is held at a temperature of 200°C 300 271 Liquid 250 232 200 a + Liquid B+Liquid 150 184 138.5C 100 a+B 50 Sn 10 20 30 40 50 60 70 80 90 Bi Weight Bismuth c) What are the proportions (%) of each phase in the alloy? Temperature, C B.

Physical Chemistry

2nd Edition

ISBN:9781133958437

Author:Ball, David W. (david Warren), BAER, Tomas

Publisher:Ball, David W. (david Warren), BAER, Tomas

Chapter6: Equilibria In Single-component Systems

Section: Chapter Questions

Problem 6.50E

See similar textbooks

Similar questions

10.11/ A 1.5-kg specimen of a 90 wt% Pb-10 wt% Sn alloy is heated to 250°C (480°F), at which temperature it is entirely an a-phase solid solution . The alloy is to be melted to the extent that 50% of the speci- men is liquid, the remainder being the a phase. This may be accomplished either by heating the alloy or changing its composi- tion while holding the temperature con- stant. (a) To what temperature must the speci- men be heated? (b) How much tin must be added to the 1.5-kg specimen at 250°C to achieve this state? 10.15) A magnesium-lead alloy of mass 5.5 ka consists of a solid a phase that has a compo- sition that is just slightly below the solubility limit at 200°C (390°F). (a) What mass of lead is in the alloy? (b) If the alloy is heated to 350°C (660°F). how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? 10.27 A hypothetical A-B alloy of composition 55 wt% B-45 wt% A at some temperature is found to consist of mass…
An aerospace manufacturer is building a prototype experi-mental aircraft that cannot be detected by radar. Boron nitride ischosen for incorporation into the body parts, and the boricacid/ammonia method is used to prepare the ceramic material.Given 85.5% and 86.8% yields for the two reaction steps, howmuch boron nitride can be prepared from 1.00 metric ton of boric acid and 12.5 m³ of ammonia at 275 K and 3.07X10³ kPa?Assume that ammonia does not behave ideally under these con-ditions and is recycled completely in the reaction process.
The table below shows temperature/composition data collected for a mixture of methylbenzene (M) and octane (O) at 1 atm. Recall that x stands for the mole fraction in the liquid and y stands for the mole fraction in the vapor in equilibrium. The boiling points for methylbenzene (M) and octane (O) are 110.60C and 125.60C, respectively. Construct the phase diagram with Temperature vs. xM. What is the composition of the vapor in equilibrium with the liquid of composition (a) xM = 0.250 and (b) xO = 0.250. T (0C) 110.9 112.0 114.0 115.8 117.3 119.0 121.1 123.0 xM 0.908 0.795 0.615 0.527 0.408 0.300 0.203 0.097 yM 0.923 0.836 0.698 0.624 0.527 0.410 0.297 0.164
6.1) At the composition of 0.77% by weight C, identify the phase(s) presentat 950 degrees C 6.2) When the specimen is at 950 degrees C, what is the maximum C composition at which a single phase Austenite is stable?6.3) If we slowly cool a Fe-C alloy with 0.77% by weight C, austenitized at950 degrees C, to just below the eutectoid temperature of 727 degrees C, give the weight percentage and composition of the phases present based on the phase diagram given above6.4) If we cool very quickly a Fe-C alloy with 0.77% by weight C,austenitized at 950 degrees C, to room temperature, give the weight percentage and composition of the phase(s) present
Sketch the cooling curves for the isopleths a and b in Fig. 5.4.
a) The following temperature composition data were obtained for a mixture of two liquids A and B at one atmosphere, where x is the mole fraction of A in the liquid and y is the mole fraction of A in the vapour, at equilibrium.t/ oC 125 130 135 140 145 150xA 0.91 0.65 0.45 0.30 0.18 0.098yA 0.99 0.91 0.77 0.61 0.45 0.25the boiling points are 124 oC for A and 155 oC for B. Plot the temperature-composition diagram for the mixture on a graph sheet. What is the composition of the vapour in the equilibrium with the liquid of composition i) xA = 0.50 and ii) xB= 0.33
is the phase diagram of sulphur. At 95.4˚C, the densities of rhombic andmonoclinic sulphur are 2.07 g cm-3and 1.96 g cm-3, whilst the enthalpy change for thephase transition from rhombic to monoclinic sulphur is 0.3 kJ mol-1. i) How many triple points are there?ii) What is the most stable form of sulphur under normal conditions?iii) Describe what happens when sulphur at 1 atm is heated from 80˚C to 200˚C.iv) Determine the volume change ΔV for the transformation from rhombic tomonoclinic sulphur.v) Estimate the pressure at which rhombic and monoclinic sulphur coexist inequilibrium at a temperature of 373 K.
The composition of the liquid and the vapor that are in equilibrium is not necessarily the same. T or F
What is the amount of energy required (in KJ) to convert 100g of ice at -20 degrees to steam vapour at 120 degrees? If the total amount of surfactant to be used in an emulsion is 5g, calculate the amount of Span 80 (HLB=4.3) and Tween (HLB =16.7) in order to obtain an HLB value of 9.5
Referring to the Al-Si Eutectic diagram discussed on the Phase Diagrams-Lever Rule handout, calculate the mass fraction of the phase, silicon, given a sample with 51.7 wt% aluminum at 576.99 ˚C.
Pressure was exerted with a piston on molten naphthalene at 95 °C. The vaporpressure of naphthalene when the applied pressure is 1.0 bar is 2.0 kPa. What is thevapor pressure when the pressure on the liquid is 15 MPa? The mass density ofnaphthalene at this temperature is 1.16 g cm-1.
Describe a binary eutectic diagram and show all phase regions with all the relevant information for each.