Construct a calibration curve based on the following data: Concentration Fe 0.100 0.500 2.00 4.00 7.00 (ppm) Absorbance 0.0122 0.0608 0.2322 0.455 0.5858 Use LINEST to find the slope and intercept and their uncertainties. Enter your answer as a number with no units to three significant figures. 0.085 0.037 b 0.100 0.500 Sm Sp r2 0.958 0.037 Sy

Construct a calibration curve based on the following data: Concentration Fe 0.100 0.500 2.00 4.00 7.00 (ppm) Absorbance 0.0122 0.0608 0.2322 0.455 0.5858 Use LINEST to find the slope and intercept and their uncertainties. Enter your answer as a number with no units to three significant figures. 0.085 0.037 b 0.100 0.500 Sm Sp r2 0.958 0.037 Sy

Chemistry & Chemical Reactivity

10th Edition

ISBN:9781337399074

Author:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Publisher:John C. Kotz, Paul M. Treichel, John Townsend, David Treichel

Chapter4: Stoichiometry: Quantitative Information About Chemical Reactions

Section: Chapter Questions

Problem 77PS

See similar textbooks

Similar questions

The absorbance for a dye sample of unknown concentration is measured and the corrected absorbance is 0.666. The standard curve created is found to have this linear equation: y = 0.153x + 0.043 Calculate the concentration (ug / mL) of the dye sample. 4.54 3.33 4.07 5.17 2.07
You are measuring the concentration of an unknown protein sample, and the absorbance at 595 nm (or A595) of your unknown is greater than that of the highest-concentration standard solution. It is not advisable to simply extrapolate the line of the standard curve to calculate the concentration of the unknown In this scenario, what would be the best strategy to measure the concentration of your unknown (instead of extrapolating from the standard curve)?
You are measuring the concentration of an unknown protein sample, and the absorbance at 595 nm (or A595) of your unknown is greater than that of the highest-concentration standard solution. It is not advisable to simply extrapolate the line of the standard curve to calculate the concentration of the unknown In this scenario, what would be the best strategy to measure the concentration of your unknown (instead of extrapolating from the standard curve)? (answer in 5 sentences)
what is the purpose y the result of Spectrophotometric of a Cobalt Chloride Solution Analysis? Table 1 Absorption Spectrum of Cobalt Chloride Using a Spectrophotometer Wavelength Absorbance 400 410 420 430 440 450 460 370 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650 660 670 680 690 700 0.036 0.044 0.063 0.095 0.147 0.215 0.284 0.329 0.362 0.402 0.450 0.479 0.464 0.398 0.314 0.216 0.142 0.087 0.054 0.041 0.036 0.036 0.034 0.028 0.030 0.023 0.023 0.023 0.014 0.014 0.011 Test Tube Number Cobalt Chloride Concentration (mol/mL) Absorbance at 510 nm 1 0.000 0.000 2 0.009 0.042 3 0.018 0.92 4 0.027 0.139 5 6 0.036 0.045 0.190 0.236 7 (Unknown) 0.151
Concentration [M] Absorbance Solution 1 86.29 0.64 Solution 2 51.986 0.29 …. Fig 1: [graph of the calibration curve, make sure to show: function, R2, 0 intercept]
Derive an expression relating absorbance to the concentrations of standard and unknown ( c subscript s and c subscript x) and the volumes of the standards and unknown ( V subscript s and V subscript x ) as well as the volume to which the solutions were diluted (V subscript t). Derive expressions for the slope and the intercept of the straight line obtained in (a) in terms of the variables listed above.
Five standard chromium (VI) solutions were prepared through serial dilution technique with corresponding absorbance readings at 540 nm wavelength (as follows: Absorbance Concentration A1 = 0.650 C1 = 1.9 ppm A2 = 0.712 C2 = 4.0 ppm A3 = 1.370 C3 = 6.0 ppm A4 = 2.050 C4 = 8.0 ppm A5 = 3.423 C5 = 10.0 ppm The sample solution gives an average absorbance reading of 0.713. What is then the concentration of chromium (VI) ion in the sample?
Five standard chromium (VI) solutions were prepared through serial dilution technique with corresponding absorbance readings at 540 nm wavelength as follows: Absorbance Concentration A1 = 0.650 C1 = 1.9 ppm A2 = 0.712 C2 = 4.0 ppm A3 = 1.370 C3 = 6.0 ppm A4 = 2.050 C4 = 8.0 ppm A5 = 3.423 C5 = 10.0 ppm The sample solution gives an average absorbance reading of 0.713. What is then the concentration of chromium (VI) ion in the sample? (Note: please provide necessary solutions)
A solution of KMnO4 with a concentration of 8.25 x 10-5 M yields an absorbance value of 0.1302 when measured in a 5.60 cm cuvette, set at a wavelength of 725 nm. Compute for the Molar Absorptivity Coefficient of the sample. Choices: a. 2.8182x10-8 c. 4.8182x10-8 b. 3.8182x10-8 d. 5.8182x10-8
Plot a professional quality standard curve (absorbance vs. protein amount in µg) with an appropriate title and caption underneath the plot from the data give above. The caption should include the best-fit data.
Monomer-dimer formation can affect the absorbance measurements using Beer’s law, it is an example of: A. chemical deviation B. instrumental deviation C. real deviation D. instrumental deviation
What percent transmittance range and what absorbance range are considered to be the optimum working ranges for spectrochemical measurements?