The electric field profile in the depletion region of a p-n junction in equilibrium is shown in the gure. Which one of the following statement is not true? E (V/cm) 0.1 O Both n-type and p-type depletion regions are uniformly doped. O The potential difference across the depletion region is 700 mV. 16 If the p-type region has a doping contration of 10 cm?, then the doping of the n-region is 10" cm 3 O Left side of the junction in n-type and right side is p-type.

The electric field profile in the depletion region of a p-n junction in equilibrium is shown in the gure. Which one of the following statement is not true? E (V/cm) 0.1 O Both n-type and p-type depletion regions are uniformly doped. O The potential difference across the depletion region is 700 mV. 16 If the p-type region has a doping contration of 10 cm?, then the doping of the n-region is 10" cm 3 O Left side of the junction in n-type and right side is p-type.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

A certain PN junction has a linearly graded junction on the p-side, Na = ax, where x is the distance from the physical junction to p-side and a = 1019 cm-4 , and a uniform doping of 3 x 1014 cm-3 on the n-side. It is operated at T=300K. A. Calculate the electric field as a function of x? B. If the depletion layer width of the p-side is .8um at zero bias, find the total depletion layer width
consider a silicon pn junction of doping concentrations of 5*10^16 cm-3 and 2*10^15 cm-3 at the p-side and n-side respectively if the pn-junction is forward biased y a voltage V=0.5 V considering a steady state. i) solve the continuity equation in the p side to find the electron concentration as a function of distance x . ii) find the electron current density Jn in the p-side at a distance 10 nm from the edge of the depletion layer.
A pn junction operating in this forward-bias region with a current I of 0.4 mA is found to have a diffusion capacitance of 1 pF. What diffusion capacitance do you expect this junction to have at I = 0.1 mA? What is the mean transit time for this junction?
Answer ASAP, I'll upvote. Thanks. Take the first part of the energy band figure shown below where material A is attached to material B. If a positive voltage was applied to A, and B was attached to ground, is the AB junctionforward-biased or reverse-biased? The built-in voltage of a PN junction is due to a charge gradient between the two sides of the junction, as shown by the graphs. What is the cause of this charge gradient? Answer in 1 sentence.
A diffused silicon PN junction has a linearly graded junction in the P-side with ?=10^19cm−3, and a uniform doping of 3×10^14 cm−3on the N-side. If the depletion layer width of the P-side is 0.8μm at zero bias, find the total depletion layer width, built-in potential, maximum field at zero bias and sketch the potential distribution.
Hall measurement is conducted on a silicon sample of unknown doping with W= 100cm, A = 2.5 × 10-3cm2, I = 2 mA and the magnetic field is 500 Gauss. If the Hall voltage of +150mV is measured, find the Hall coefficient, conductivity type, majority carrier concentration, resistivity and mobility of the semiconductor sample.
A GaAs semiconductor sample is doped with donors (ND = 1015 cm-3). Calculate the intrinsic temperature. Intrinsic temperature is the temperature at which a doped semiconductor becomes intrinsic. Assume room temperature values for Eg, NC, NV. Also assume that the three parameters (Eg, NC, NV) are independent of temperature. Hints: Calculate the temperature at which ni = ND. Eg = 1.42 eV (T = 300K) Get room T NC and NV values from the book or from lecture 3.
A silicon diode is fabricated by starting with an n-type substrate (Nd = 1016 cm-3), into which indium is diffused to form as a p-type region doped at 1018 cm-3. Assuming that an abrupt p+ -n junction is formed by the diffusion process. a. Calculate the Fermi level position in the p and n regions b. Determine the built in potential c. Calculate the depletion widths on the p and n side.
Consider the above semiconductor structure, where Al is alloyed into an n-type Si sample with Nd=1016 cm-3 that formed a circular cross-section junction of diameter 0.02 inch. If the acceptor ion concentration in the alloyed regrown region is Na=4x1018 cm-3 then for this junction at thermal equilibrium calculate- (a) V0, xn0, xp0, Q+ and ε0.(b) Draw the charge density and electric field distribution within the region, W.
Given a Si sample of unknown doping, Hall measurement has been made and thefollowing information obtained: W = 0.05 cm, A = 1.6 x 10-3 cm2, I = 2.5 mA, and themagnetic field is 30 nT (1T = 104 Wb/cm2). If a Hall voltage of +10 mV is measured, findthe Hall coefficient, conductivity type, majority carrier concentration resistivity, and mobilityof the semiconductor sample.
Consider an asymmetric p-n junction which has a heavily-doped n-type side relative the p-type side. ND >> NA. Assume that the p and n-type sides are based from the same material. Sketch the following graphs, Q(x), E(x), V(x) and energy band diagram, for the following conditions: with no bias with a forward bias V
Given a Si sample of unknown doping, Hall measurement has been made and thefollowing information obtained: W = 0.05 cm, A = 1.6 x 10-3 cm2, I = 2.5 mA, and themagnetic field is 30 nT (1T = 104 Wb/cm2). If a Hall voltage of +10 mV is measured, findthe Hall coefficient, conductivity type, majority carrier concentration, resistivity, and mobility of the semiconductor sample.