Heating Ventilating and Air Conditioning: Analysis and Design
6th Edition
ISBN: 9780471470151
Author: Faye C. McQuiston, Jeffrey D. Spitler, Jerald D. Parker
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.13P
Water flowing at a rate of 1.5 kg/s through a heat exchanger heats air from 20 C to 30 C flowing at a rate 2.4 m3/s. The water enters at a temperature of 90 C, and the air is at 0.1 MPa. At what temperature does the water leave the exchanger?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Water flows through two adiabatic turbines and a heat exchanger as shown in the picture. Hot air is used to provide additional energy to the water between the two turbines. The first turbine has a power output of 8,000 kW. Determine the power output of the second turbine in kW and the process efficiency of each turbine.
Determine the state of steam in turbine 1, Formulate the 1st Law for turbine 1, and solve for the flow rate of steam.
Formulate the 1st Law for the heat exchanger, and solve for the temperature at exit
In a steam-heating system, air is heated by being passed over some tubes through which steam flows steadily. Steam enters the heat exchanger at 30 psia and 400°F at a rate of 15 lbm/min and leaves at 25 psia and 212°F. Air enters at 14.7 psia and 80°F and leaves at 130°F. Determine the volume flow rate of air at the inlet.
Hot exhaust gases leaving an internal combustion engine at 400°C and 150 kPa at a rate of 0.8 kg/s are to be used to produce saturated steam at 200°C in an insulated heat exchanger. Water enters the heat exchanger at the ambient temperature of 20°C, and the exhaust gases leave the heat exchanger at 350°C. Determine the second-law efficiency of the heat exchanger.
Chapter 1 Solutions
Heating Ventilating and Air Conditioning: Analysis and Design
Ch. 1 - Convert the following quantities from English to...Ch. 1 - Convert the following quantities from SI to...Ch. 1 - A pump develops a total head of 50 ft of water...Ch. 1 - A fan is observed to operate with a pressure...Ch. 1 - The electric utility rate for a facility during...Ch. 1 - For the business whose monthly electrical energy...Ch. 1 - Detmine the interest rate at which the project in...Ch. 1 - How much could a company afford to spend on an...Ch. 1 - Make the following volume and mass flow rate...Ch. 1 - A room with dimensions of 31020m is estimated to...
Ch. 1 - Compute the heat transferred from water as it...Ch. 1 - Air enters a heat exchanger at a rate of 5000...Ch. 1 - Water flowing at a rate of 1.5 kg/s through a heat...Ch. 1 - Air at a mean temperature of 50 F flows over a...Ch. 1 - Repeat Problem 1-10 for air at 10 C, a tube with...Ch. 1 - Air at 1 atm and 76 F is flowing at the rate of...Ch. 1 - Air flowing at the rate of 1000 cfm and with a...Ch. 1 - A chiller is providing 5 tons of cooling to an air...Ch. 1 - Air is delivered to a room at 58 F and the same...Ch. 1 - A chiller is to pro;ide 12 tons of cooling to a...Ch. 1 - Air is being rnished to a 30-ft by 40-ft by 12-ft...Ch. 1 - If cold outside air at 20 F is leaking into a...Ch. 1 - A Btu-meter is a device that measures water flow...Ch. 1 - A heat pump uses a 100,000-gallon swimming pool as...Ch. 1 - A heat pump uses a 100,000-gallon swimming pooi as...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A man uses a crowbar to lift the corner of a hot tub for maintenance purposes. Determine the moment made by the...
Engineering Mechanics: Statics
Determine the magnitude of forces F1, F2, F3, so that the particle is held in equilibrium.
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Comprehension check 12-10
The preceding graph shows the ideal gas Jaw relationship (PV =nRT) between pressure (...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
The support reactions. Also, draw the free body diagrams of Joints A, B, and C of the truss.
Engineering Mechanics: Statics & Dynamics (14th Edition)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In general, heat exchangers with higher flow rates have greater capacities?arrow_forwardThe gases flow through a gas turbine at the rate of 17kg/s and the power developed by the turbine is 14MW.The enthalpies of the gases at inlet and outlet are 1200kJ/kg and 360kJ/kg respectively, and the velocities of the gases inlet and outlet are 60m/s and 150m/s respectively. Calculate the rate of heat rejected from the turbine and the area of the inlet pipe given that the specific volume of the gases at inlet is 0.5m3/kg.arrow_forwardIn large gas-turbine power plants, air is preheated by the exhaust gases in a heat exchanger called the regenerator before it enters the combustion chamber. Air enters the regenerator at 1 MPa and 550 K at a mass flow rate of 800 kg/min. Heat is transferred to the air at a rate of 2700 kJ/s. Exhaust gases enter the regenerator at 140 kPa and 800 K and leave at 130 kPa and 600 K. Treating the exhaust gases as air, determine the mass flow rate of exhaust gases.arrow_forward
- In large gas-turbine power plants, air is preheated by the exhaust gases in a heat exchanger called the regenerator before it enters the combustion chamber. Air enters the regenerator at 1 MPa and 550 K at a mass flow rate of 800 kg/min. Heat is transferred to the air at a rate of 2700 kJ/s. Exhaust gases enter the regenerator at 140 kPa and 800 K and leave at 130 kPa and 600 K. Treating the exhaust gases as air, determine the exit temperature of the air.arrow_forwardAir is drawn into the compressor at pressure of 100 kPa and temperature of 22ºC. The volumetricflow rate at the compressor inlet is 0.4 m3/s. The compressor exit pressure is 900 kPa and thecompressor efficiency is 70%. The air leaving the compressor passes through a heat exchangerwhere it is cooled by transferring heat to the atmosphere at 22ºC. The outlet temperature of airafter the heat exchanger is 32ºC. The air passes through a valve and enters a 1 m3 rigid tank. Theinitial pressure and temperature of the air in the tank are 100 kPa and temperature of 22ºC,respectively. The final pressure and temperature of the air in the tank are 900 kPa and temperatureof 90ºC. During the filling process, the tank transfers heat to the surroundings (at 22ºC).Don’t assume constant specific heat.Determinea) The mass flow rate of air entering the compressor, ?̇ (kg/s).b) The rate of power consumed by the compressor, (kW).c) The rate of heat transfer from the heat exchanger to the atmosphere, (kW).d)…arrow_forwardWater enters the constant 120-mm inside-diameter tubes of a boiler at 7 MPa and 65°C and leaves the tubes at 6 MPa and 450°C with a velocity of 85 m/s. Calculate the velocity of the water at the tube inlet and the inlet volume flow rate.arrow_forward
- --SHOW AN ILLUSTRATION AND THE COMPLETE SOLUTION--An air compressor receives 272 kg/min of air at 99.29 kPa and a specific volume of 0.026 m3/kg. The air flows steady through the compressor and is discharged at 689.5 kPa and 0.0051 m3/kg. The initial internal energy of the air is 1594 J/kg; at discharge, the internal energy is 6241 J/kg. The cooling water circulated around the cylinder carries away 4383 J/kg of air. The change in kinetic energy is 896 J/kg increase. Compute the work.-answer in KWarrow_forwardIn a continuous flow open system, the inlet velocity of the flowing fluid is 30 m/s, and the outlet enthalpy is 100 kJ/kg less than the inlet enthalpy. The entry point of the system is 1.5 m higher than the exit point.a) Calculate the exit velocity since the system does not exchange heat and work with its surroundings.b) Since the system is adiabatic and the velocity of the fluid at the outlet is 150 m/s, find the work done by 1 kg of fluid.c) Since there is no heat exchange between the system and its surroundings and the velocity of the fluid at the exit is 30 m/s, find the heat exchange of 1 kg fluid with the environment.arrow_forwardThe mass flow rate of the gas in a gas turbine is 40 kg/s. The specific enthalpy and velocity in the inlet are 1300 kJ/kg and 160 m/s respectively while the outlet are 350 kJ/kg and 50 m/s respectively. Calculate for the work of the turbine if there is a heat loss of 1000 kW. (kW)arrow_forward
- A steam condenser is supplied with steam, which has a specific enthalpy (calculated above 0 C) of 2-2 MJ/kg and a velocity of 70 m/s, at a rate of 2200 kg/h. The water leaving the condenser has negligible velocity and a temperature of 28°C Determine the heat absorbed by the cooling water per minute, and the required flow rate of cooling water for a temperature increase of 20 C, assuming no externalheat exchangesarrow_forwardIn a gas turbine , the flow rate of air is 4 kg/sec . The velocity and enthalpy of air at the entrance are 200 m/sec and 6000 KJ/kg respectively . At the exit , the velocity is 100 m/sec and enthlpy is 5000 KJ /kg . A loss of heat of 40 KJ/kg occurs while the air passes through the turbine . Determine the power developed by the turbinearrow_forwardWater at 90C is being pumped from a large storage tank at 1 atm abs at a rate of 0.189 m3/min by a pump. The motor that drives the pump supplies energy to the pump at a rate of 2 hp. The water pumped through a heat exchanger, where it gives up 700 kW of heat and is then delivered to a large open storage tank at an elevation of 20 m above the first tank. What is the final temperature of the water to the second tank? Neglect kinetic energy.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Plant Explained | Working Principles; Author: RealPars;https://www.youtube.com/watch?v=HGVDu1z5YQ8;License: Standard YouTube License, CC-BY