Fundamentals of Heat and Mass Transfer
7th Edition
ISBN: 9780470501979
Author: Frank P. Incropera, David P. DeWitt, Theodore L. Bergman, Adrienne S. Lavine
Publisher: Wiley, John & Sons, Incorporated
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 11, Problem 11.55P
To determine
The mass flow rate for exhaust gases.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
2- In a heat exchanger, steam of 0.08 bar and a specific steam content of 95% is condensed. 381.6 tons / h cooling water with a temperature of 10 ̊C flows in parallel connected tubers with inner / outer diameter 28/30 mm with a speed of 0.65 m / s. The heat transfer surface of the heat exchanger is 220 m2 and it has a k-value of 2200 W / (m2K) . Assume the specific heat capacity of the water 4.18 kJ / (kg K) and density 1000 kg / m3. The K-value is attributed to the outer mantle surface of the tubes.
a) Calculate the outlet temperature of cooling water.
b) How many tonnes of steam per hour are condensed?
c) Determine the number of tubes and tube length
Hot water flowing at 0.015 m3/min enters the tube side of a counter current shell & tube heat exchanger at 80 C and leaves at 50 C. Cold oil flowing thru the shell at 0.05 m3/min, with density 800 kg/m3 and specific heat of 2.0 kJ/kg K, enters at 20 C. Consider water specific heat at 4.2 kJ/kg K and density of 988 kg/m3 at above condition, what is the approximate Log Mean Temperature Difference (LMTD)? Show the temperature profile completely labeled.
In a countercurrent double-pipe heat exchanger, the hot oil entering the inner tube at 420 K with a flow rate of 60 g/s is required to be cooled to 320 K. In the space between the outer tube and the inner tube of the heat exchanger, cooling water flows at the same linear speed as the oil. Cooling water enters the heat exchanger at 290 K. The inner tube inner diameter of the heat exchanger is 25 mm and the outer tube inner diameter is 40 mm. Calculate the length of the heat exchanger. The oil side heat transfer coefficient is 1.6 kW/m2 K, and the water side heat transfer coefficient is 3.6 kW/m2 K. The densities of oil and water can be taken as 0.8 and 1.0 g/cm3, respectively, and the specific heats of oil and water can be taken as 2.0 and 4.2 kJ/kg K, respectively. Wall effects can be neglected.
Flow cross-sectional area = (PI)*D2 /4
F2
Chapter 11 Solutions
Fundamentals of Heat and Mass Transfer
Ch. 11 - In a fire-tube boiler, hot products of combustion...Ch. 11 - A shell-and-tube heat exchanger is to heat an...Ch. 11 - A steel tube (k=50W/mK) of inner and outer...Ch. 11 - A heat recovery device involves transferring...Ch. 11 - A novel design for a condenser consists of a tube...Ch. 11 - The condenser of a steam power plant...Ch. 11 - Thin-walled aluminum tubes of diameter D = 10mmare...Ch. 11 - A tinned-tube, cross-how heat exchanger is to use...Ch. 11 - Water at a rate of 45,500kg/h is heated from 80...Ch. 11 - A novel heat exchanger concept consists of a...
Ch. 11 - Prob. 11.12PCh. 11 - A process fluid having a specific heat of...Ch. 11 - A shell-and-tube exchanger (two shells, four tube...Ch. 11 - Consider the heat exchanger of Problem 11.14....Ch. 11 - The hot and cold inlet temperatures to a...Ch. 11 - A concentric tube heat exchanger of length L = 2 m...Ch. 11 - A counterflow, concentric tube heat exchanger is...Ch. 11 - Consider a concentric tube heat exchanger with an...Ch. 11 - A shell-and-tube heat exchanger must be designed...Ch. 11 - A concentric tube heat exchanger for cooling...Ch. 11 - A counterflow, concentric tube heat exchanger used...Ch. 11 - An automobile radiator may be viewed as a...Ch. 11 - Hot air for a large-scale drying operation is to...Ch. 11 - In a dairy operation, milk at a flow rate of 250...Ch. 11 - The compartment heater of an automobile...Ch. 11 - A counterflow, twin-tube heat exchanger is made...Ch. 11 - Consider a coupled shell-in-tube heat exchange...Ch. 11 - For health reasons, public spaces require the...Ch. 11 - A shell-and-tube heat exchanger (1 shell pass, 2...Ch. 11 - Saturated water vapor leaves a steam turbine at a...Ch. 11 - The human brain is especially sensitive to...Ch. 11 - Prob. 11.47PCh. 11 - A plate-tin heat exchanger is used to condense a...Ch. 11 - In a supercomputer, signal propagation delays...Ch. 11 - Untapped geothermal sites in the United States...Ch. 11 - A shell-and-tube heat exchanger consists of 135...Ch. 11 - An ocean thermal energy conversion system is...Ch. 11 - Prob. 11.55PCh. 11 - Prob. 11.56PCh. 11 - The chief engineer at a university that is...Ch. 11 - A shell-and-tube heat exchanger with one shell...Ch. 11 - Prob. 11.59PCh. 11 - Prob. 11.60PCh. 11 - Prob. 11.61PCh. 11 - Prob. 11.62PCh. 11 - A recuperator is a heat exchanger that heats air...Ch. 11 - Prob. 11.64PCh. 11 - Prob. 11.65PCh. 11 - A cross-flow heat exchanger consists of a bundle...Ch. 11 - Exhaust gas from a furnace is used to preheat the...Ch. 11 - Prob. 11.68PCh. 11 - A liquefied natural gas (LNG) regasification...Ch. 11 - Prob. 11.70PCh. 11 - A shell-and-tube heat exchanger consisting of...Ch. 11 - Prob. 11.73PCh. 11 - The power needed to overcome wind and friction...Ch. 11 - Prob. 11.75PCh. 11 - Consider a Rankine cycle with saturated steam...Ch. 11 - Consider the Rankine cycle of Problem 11.77,...Ch. 11 - Prob. 11.79PCh. 11 - Prob. 11.80PCh. 11 - Hot exhaust gases are used in a...Ch. 11 - Prob. 11.84PCh. 11 - Prob. 11.90PCh. 11 - Prob. 11S.1PCh. 11 - Prob. 11S.2PCh. 11 - Prob. 11S.3PCh. 11 - Solve Problem 11.15 using the LMTD method.Ch. 11 - Prob. 11S.5PCh. 11 - Prob. 11S.6PCh. 11 - Prob. 11S.8PCh. 11 - Prob. 11S.10PCh. 11 - Prob. 11S.11PCh. 11 - A cooling coil consists of a bank of aluminum...Ch. 11 - Prob. 11S.17P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 10-m-long countercurrent-flow heat exchanger is being used to heat a liquid food from 20 to 80 C. The heating medium is oil, which enters the heat exchanger at 150 C and exits at 60 C. The specific heat of the liquid food is 3.9 kJ/(kg K). The overall heat-transfer coefficient based on the inside area is 1000 W/ (m2 K). The inner diameter of the inside pipe is 7 cm. a. Estimate the flow rate of the liquid food. b. Determine the flow rate of the liquid food if the heat exchanger is operated in a concurrent-flow mode for the same conditions of temperature at the inlet and exit from the heat exchanger.arrow_forwardConsider a liquid (Cp = 2.2 kJ /kg·K) is cooled at a rate of 12 kg/min from 150°C to 40°C in the tube side ofa double-pipe counterflow heat exchanger. Water (Cp = 4.18 kJ /kg·K) enters the heat exchanger at 10°C ata rate of 9 kg/h. The outside diameter of the inner tube is 2.5 cm, and its length is 6.0 m. Calculate the overallheat transfer coefficient. (Answer: U = 2.31 kW/m2·K)arrow_forwardAir enters a cooler at 1450C and at a pressure of 3 bar and is cooled to 450C by passing through tubes of 10 mm inside diameter surrounded by water which enters the cooler at 150C and exits at 300C. Assuming the heat exchanger is counter flow, find: I) The mean temperature difference. ii) If the air velocity is limited to 6.5 m/s, what is the required length of tube? Neglect the resistance of the tube and assume water side heat transfer coefficient is 232 W/m2K.arrow_forward
- 5000 kg of dry air per hour is cooled from 60 oC to 34 oC in a countercurrent heat exchanger. In the cooling process, the cold air supplied to the heat exchanger is used at a speed of 6200 kg/h and at 20 oC. If the same amount of hot air was cooled from 60 oC to 24 oC in a longer heat exchanger with the help of cold air under the same conditions, determine what the ratio of the new heat exchanger length to the original heat exchanger length would be (assume the specific heat of the air is constant).arrow_forwardA double-pipe parallel-flow heat exchanger is used to heat water (cp = 4180 J/kg·K) from 25°C to 60°C at a rate of 0.2 kg/s. The heating is accomplished by geothermal water (cp = 4310 J/kg·K) available at 134°C at a mass flow rate of 0.3 kg/s. The inner tube is thin-walled and has a diameter of 0.8 cm. If the overall heat transfer coefficient of the heat exchanger is 550 W/m2·K, determine the length of the tube required to achieve the desired heating. (Round the answer to a single decimal place.) The length of the tube required to achieve the desired heating is ________ m.arrow_forwardMilk is flowing through a heat exchanger at a rate of 2000 kg/h. The heat exchanger supplies 111,600 kJ/h. The outlet temperature of the product is 95C. Determine the inlet temperature of the milk. The product specific heat 3.9 kJ/kg degrees Carrow_forward
- A shell and tube heat exchanger is designed as a counter to cool a mass flow rate of 60 kg/h of engine oil (cp = 1060 J/kg oC) from 300oC to 150oC. The cooling water, cp = 4182 J/kgoC, enters the tube side (Length is 1.75 m and Outer diameter is 2.54 cm) at a temperature of 20oC. If the overall heat transfer coefficient, U, is 10.83 W/m2o C and the Capacity Ratio of the Heat Exchanger is 2.4, calculate the following: a)The heat transfer rate,b)The mass flow rate of the cooling water in the units of (kg/h),C)The surface area of the heat exchanger,arrow_forwardA double tube heat exchanger is made of copper (k = 380 W / m. ° C). Inner diameter of inner tube Di = 1.2 cm, outerits diameter is D0 = 1.6 cm and the diameter of the outer pipe is 3.0 cm. Convection heat transfer coefficient on the inner surface of the pipehigh = 700 W / m2. ° C and the heat transfer coefficient on the outer surface h0 = 1400 W / m2. ° C. Pipe sidecontamination factor Rf, i = 0.0005 m2. ° C / W and fouling factor Rf on the body side, 0 = 0.0002 m2. ° C / WAccording to the example; Calculate the thermal resistance of the heat exchanger per unit length.arrow_forwardA double tube heat exchanger is made of copper (k = 380 W / m. ° C). Inner diameter of inner tube Di = 1.2 cm, outerits diameter is D0 = 1.6 cm and the diameter of the outer pipe is 3.0 cm. Convection heat transfer coefficient on the inner surface of the pipehigh = 700 W / m2. ° C and the heat transfer coefficient on the outer surface h0 = 1400 W / m2. ° C. Pipe sidecontamination factor Rf, i = 0.0005 m2. ° C / W and fouling factor Rf on the body side, 0 = 0.0002 m2. ° C / WAccording to the example; Total heat transfer coefficients (U0 and Ui), taking into account the inner and outer surface areas of the pipecalculate.arrow_forward
- A water-to-water double pipe heat exchanger is required to cool down 4200 kg/h hot process water from 120°C to 80°C. Available for this purpose is 3800 kg/h cold water at 30°C. The inner pipe inside diameter is 2.7 cm while outside diameter of the inner pipe is 3.3 cm. If the overall heat transfer coefficient is 580 W/(m2·K), calculate the length of the heat exchanger required to achieve the desired heating. Use heat capacity of water as 4.2 J/(g·K) for both streams.arrow_forwardIn an heat exchanger of parallel flow type, water enters at 60°C and leaves at 80°C while oil of specific gravity 0.8 enters at 250°C and leaves at 100°C. The specific heat of oil is 2.5 kJ/kg K and surrounding temperature is 300 K. Determine the loss in availability on the basis of one kg of oil flow per second.arrow_forwardA heat exchanger contains 400 tubes with inner diameter of 23 mm and outer diameter of 25 mm. The length of each tube is 3.7 m. The corrected log mean temperature difference is 23°C, while the inner surface convection heat transfer coefficient is 3410 W/m2·K and the outer surface convection heat transfer coefficient is 6820 W/m2·K. If the thermal resistance of the tubes is negligible, determine the heat transfer rate.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning
Principles of Heat Transfer (Activate Learning wi...
Mechanical Engineering
ISBN:9781305387102
Author:Kreith, Frank; Manglik, Raj M.
Publisher:Cengage Learning
How Shell and Tube Heat Exchangers Work (Engineering); Author: saVRee;https://www.youtube.com/watch?v=OyQ3SaU4KKU;License: Standard Youtube License