Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840728
Author: Limbrunner
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 11, Problem 11.69SP
A wood block, subjected to a tensile load, fails on a plane whose perpendicular is at an angle of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A hole 12 mm diameter is to be punched through a plate 18 mm thick. If the shear strength of the material is 300 N/mm?, find the load required on the punch.
A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the stress in the rope?
A bar is applied a tensile load of 50 kN having diameter 10 mm,
Calculate the tensile stress induced in the bar.
Chapter 11 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 11 - Prob. 11.1PCh. 11 - A rectangular ASTM A36 steel bar 2 in. by 6 in. in...Ch. 11 - Calculate Poisson’s ratio for a cast iron that has...Ch. 11 - Modulus of elasticity, modulus of rigidity, and...Ch. 11 - Compute all the dimensional changes for the steel...Ch. 11 - A surveyor’s steel tape is exactly 100ft long...Ch. 11 - An aluminum wire is stretched between two rigid...Ch. 11 - Prob. 11.8PCh. 11 - A concrete roadway pavement is placed in 60ftlong...Ch. 11 - Prob. 11.10P
Ch. 11 - A 4in. -by- 8in . short wood post is reinforced on...Ch. 11 - A short post. 150mm by 150mm , of Douglas fir, is...Ch. 11 - The cables of a power line are copper-coated steel...Ch. 11 - Prob. 11.14PCh. 11 - For the short column shown, assuming that lateral...Ch. 11 - A 1.0 -in.-diameter hole is drilled on the...Ch. 11 - Prob. 11.17PCh. 11 - A long, flat steel bar 4 in. wide and 38 thick is...Ch. 11 - A long, flat steel bar 5 in. wide and 38 thick has...Ch. 11 - 11.20 An aluminum specimen of circular cross...Ch. 11 - Prob. 11.21PCh. 11 - Prob. 11.22PCh. 11 - 11.23 A concrete cylinder, -in, in diameter, was...Ch. 11 - Prob. 11.24PCh. 11 - For the element of Problem 11.24: a. Locate the...Ch. 11 - Prob. 11.26CPCh. 11 - Prob. 11.27CPCh. 11 - Prob. 11.28CPCh. 11 - Prob. 11.29CPCh. 11 - A 50 -mm-diameter ASTM A36 steel rod is subjected...Ch. 11 - A 4 -ft-long square ASTM A36 steel bar, 2 in. by 2...Ch. 11 - A concrete test cylinder is 150 mm in diameter and...Ch. 11 - A 14 -in.-long steel rod, 112 in diameter, was...Ch. 11 - Determine the change in the diameter of an ASTM...Ch. 11 - 11.35 The steel bar shown in Figure 11.3 (see...Ch. 11 - Compute the change in the thickness of the ASTM...Ch. 11 - The steel rails of a railroad track are laid in...Ch. 11 - A rolled brass rod and a steel rod are secured to...Ch. 11 - 11.39 A -m-long steel member is set snugly between...Ch. 11 - 11.40 The distance between two fixed points on a...Ch. 11 - A steel truss is loaded as shown. The...Ch. 11 - 11.42 For the truss of Problem 5.25, the members...Ch. 11 - A surveyor’s steel tape has a cross-sectional area...Ch. 11 - A 1 -in.-diameter ASTM A36 steel tie rod, 30 ft...Ch. 11 - 11.45 A copper wire is held taut between two...Ch. 11 - 11.46 A horizontal steel member is anchored at...Ch. 11 - 11.47 Three vertical steel wires are loaded as...Ch. 11 - 11.48 Assume for Problem 11.47 that the same load...Ch. 11 - The rod shown is firmly attached to rigid...Ch. 11 - 11.50 A structural steel bar mm in width and mm...Ch. 11 - A redwood timber member having a 16 -in.-square...Ch. 11 - A steel pipe has an outside diameter of 12 in. and...Ch. 11 - A short 14 -in.-square concrete pier is reinforced...Ch. 11 - An ASTM A36 steel rod, 375.06 mm long and having a...Ch. 11 - An aluminum rod with an area of 1.5in.2 and an...Ch. 11 - A solid brass cylinder with a cross-sectional area...Ch. 11 - Three 14 in.-diameter wires are symmetrically...Ch. 11 - Rework Problem 11.57 with outer wires of aluminum,...Ch. 11 - Three rods support a weight, as shown. The...Ch. 11 - A flat steel bar 4 in. wide and 12 thick must be...Ch. 11 - A 19 -mm-diameter hole is drilled on the...Ch. 11 - A flat bar is 38 thick and has a centrally located...Ch. 11 - A long, flat steel bar 125 mm wide and 10 mm thick...Ch. 11 - 11.64 A short -in.-diameter compression member is...Ch. 11 - Prob. 11.65SPCh. 11 - 11.66 A rectangular block of wood, in. by in. in...Ch. 11 - 11.67 A -mm-diameter rod is subjected to an axial...Ch. 11 - The rectangular plate shown is subjected to a...Ch. 11 - A wood block, subjected to a tensile load, fails...Ch. 11 - Prob. 11.70SPCh. 11 - A shaft in a speed-reduction mechanism is loaded...Ch. 11 - An axially loaded 50 -mm-by- 75 -mm steel bar has...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A U-bolt supports a load of 5,000 lb. The cross-section of the bolt has a diameter of ½ in. How much stress is induced in the sides of the bolt? note: answer must be in ksiarrow_forwardA rosette consisting of 3 gages forming, respectively, angles of θa, θb and θc with the x-axis is attached to the free surface of machine components made of material with a given Poisson’s ratio v and Modulus of elasticity E as shown in Fig. 6. Take note that strain values given above are the gage readings and not principal strains.arrow_forwardWhat is the stresses in the rail at 50°C , if there is an expansion allowance of 5 mm per rail .arrow_forward
- QUESTION 2 A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers. It is subjected to an internal pressure of 5.2 MPa. Calculate the circumferential and longitudinal stress induced. Which axially applied compressive load would reduce the longitudinal stress to zero?arrow_forwardThe central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the rivets connecting these plates to the outside plates is 1 in. If the allowable unit stress in tension on the net area is 20,000 psi, the safe tensile strength of eith central plate is A. 90,000 lb B. 88,600 lb C. 78,600 lb D. 75,800 lbarrow_forwardA steel cable with a diameter of 3.0cm supports a load of 2.0 kN. What is the frictional length increase of the cable compared with the length when there is no load if Y= 200 GPa?arrow_forward
- A wooden bar is subjected to a tensile stress of 5 mpa. What will be the values of normal stress and shear stress across a section, which makes an angle at 250 with the direction at the tensile stressarrow_forward3. A 5/8 in diameter circular rod supports part of a storage shelf in a warehouse. As products areloaded and unloaded, the rod is subjected to a tensile load that varies from 1800 to 150 lb.Draw a sketch of the variation of stress versus time, and compute the maximum stress,minimum stress, mean stress, alternating stress, and stress ratio, R. please also give the FBD every calculation, thanky ouarrow_forwardThe stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.arrow_forward
- A bar under 66,000 psi stress is loaded by a 4000 pound load. What is the bar’s cross sectional area?arrow_forwarda short square is 1 1/2 inches x 1 1/2 inches in cross section. it is on an axial tensile load of 11,000 lbs. calculate the shear stress and the tensile stress acting on the plane which is mormal and is inclined 50 degrees to the longitudinalm axis of the bar. what is the factor of safet for the bar?arrow_forwardThe stress and a pipe varies jointly with the internal pressure and the diameter of the pipe, and inversely with the square of the thickness of the pipe. The stress is 200 pounds per square inch when the diameter is 4 inches, the thickness is 0.40 inches, and the internal pressure is 25 pounds per square inch. Find distressed wood and internal pressure is 50 pounds per square inch if the diameter is 10 inches and a thickness is 0.50 inches. Define variables Stress in pipe Internal pressure of pipe Diameter of pipe Thickness of pipe Find k Update formula Answer question arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY