Concept explainers
The value of the allowable axial load pressure for the different lengths.
Answer to Problem 11.9.7P
The value of the allowable axial load pressure for the different lengths is:
S.No | Length of column( ft) | Axial load ,Pallow( k ) |
1 | 06 | 58.8 |
2 | 12 | 43.0 |
3 | 18 | 23.1 |
4 | 24 | 13.0 |
Explanation of Solution
Given Information:
The outside diameter of the steel pipe column, do =4.5 in.
The thickness of the steel pipe column, t = .237 in.
The value of the young modulus, E = 29000 ksi
The value of maximum stress, sy = 36 ksi
Concept Used:
For pinned end, K=1
Here, r = radius of gyration.
Then we try different value of
Then select the trial column
Calculation:
For pinned end, K = 1.
Here, r = radius of gyration.
For L1 = 6 ft.
For L2 =12 ft
For L3 =18 ft.
For L4 = 24 ft,
Conclusion:
The value of the allowable axial load pressure for the different lengths is:
S.No | Length of column( ft) | Axial load ,Pallow( k ) |
1 | 06 | 328 |
2 | 12 | 243 |
3 | 18 | 134 |
4 | 24 | 75.3 |
Want to see more full solutions like this?
Chapter 11 Solutions
Bundle: Mechanics Of Materials, Loose-leaf Version, 9th + Mindtap Engineering, 1 Term (6 Months) Printed Access Card
- A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?arrow_forwardThree round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.arrow_forwardA sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.arrow_forward
- A fixed-end column with circular cross section is acted on by compressive axial load P. The IS-ft-long-column has an outer diameter of 5 in., a thickness of 0.5 in., and is made of aluminum with a modulus of elasticity of 10,000 ksi. Find the buckling load of the column.arrow_forwardAn aluminum alloy tube with an outside diameter of 3.1 in. and a wall thickness of 0.36 in. is used as a 16-ft-long column. Assume that E = 9300 ksi and that pinned connections are used at each end of the column. Determine the slenderness ratio L/r and the Euler buckling load Per for the column. Answers: L/r= Por= kipsarrow_forwardIf the allowable tensile stress for the bar is (o,) allow = 21 ksi, and the allowable shear stress for the pin is Tallow = 12 ksi, determine the diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take i = in. and w = 2 in.arrow_forward
- A metal bar is made out of A-36 steel and has a diameter d 20mm with the end at A fixed to the wall. There is are balanced axial loads at B of P₁ = 50 kN and a point load at C of P2 = 40 kN. The distance from A to B is L₁ = 600 mm and the distance from B to C is L2 400 mm. Calculate the displacement of point C relative to point A. The modulus of elasticity for steel is E = 200 GPa A d B The displacement at C is 8 = P₁ 1 Р1 с BY NO SA 2021 Cathy Zupke mm P2arrow_forwardGiven: angle α=64o. Cross sections of both rods are square with sizes a1=21mm, a2=13mm. The rods are made of steel with yielding stress σY=270MPa; factor of safety n=2,2. Find: allowable value of force (in kN) from strength calculation FA = ?arrow_forwardGiven: l1=2,3l ; l2=2,9l ; l3=1,7l; F1=0,7P; F2=0P; F3 =-1,1P. Parameter of length l=40cm; parameter of loading P=26kN. The rod is made of steel with yielding stress σY=350MPa; factor of safety n=1,3. Find: the diameter (in mm) of cross section from strength calculation d = ?arrow_forward
- steel bar ABCD consists of three sections: AB is of 30mm diameter and 100 mm long, BC is 20 mm square and 400 mm long, and CD is of 12 mm diameter and 200mm long. The bar is subjected to an axial compressive load which induces a stress of 50 MN/m2 on the largest cross-section. Determine the total decrease in the length of the bar when the load is applied. For steel E = 210GN/m2 .arrow_forwardAluminum A=400 mm Bronze A = 390 mm Steel A=500 mm 2P 4P 2.5 m 2.0 m 1.5 m 4. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Fig. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. OA114 KN 1. 19 20 O C138 KN N0 O2GO P Aramak için buraya yazınarrow_forwardThe one end of a hollow square tube whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ(allowable stress) = 243 ksi for pin material.arrow_forward
- Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning