Connect 1-semester Access Card For Shigley's Mechanical Engineering Design
10th Edition
ISBN: 9780077591632
Author: Richard G Budynas; Keith J Nisbett
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 11, Problem 38P
Estimate the remaining life in revolutions of an 02-30 mm angular-contact ball bearing already subjected to 200 000 revolutions with a radial load of 18 kN, if it is now to be subjected to a change in load to 30 kN.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
What is the nominal life in working hours of a deep groove ball bearing 6308, which is carrying a constant radial load of 2.82 kN at a speed of 80 rpm.
In a particular application, the radial load acting on a ball bearing is 5 kN and the expected life for 90% of the hearings is 8000 Calculate the dynamic load carrying capacity of the bearing, when the shaft rotates at 1450 rpm.
Dynamic load number C = 40500 N, revolution n = 840 rpm and Fr = 4500 of 6309 single row fixed radial bearing carrying N load; (a) Check and interpret whether it is selected correctly for Lh=20000 hours. (b) Calculate the dynamic load number of the bearing when the load remains the same and the life is doubled.
Chapter 11 Solutions
Connect 1-semester Access Card For Shigley's Mechanical Engineering Design
Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Problems 112 and 113 raise the question of the...Ch. 11 - Prob. 5PCh. 11 - Manufacturer Rating Life, Revolutions Weibull...Ch. 11 - Two ball bearings from different manufacturers are...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...
Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - 11-8 to 11-13 For the bearing application...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - A countershaft carrying two V-belt pulleys is...Ch. 11 - For the shaft application defined in Prob. 3-77,...Ch. 11 - For the shaft application defined in Prob. 3-79,...Ch. 11 - An 02-series single-row deep-groove ball bearing...Ch. 11 - An 02-series single-row deep-groove ball bearing...Ch. 11 - 11-22 to 11-26 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - 1122 to 1126 An 02-series single-row deep-groove...Ch. 11 - The shaft shown in the figure is proposed as a...Ch. 11 - Repeat the requirements of Prob. 11-27 for the...Ch. 11 - The shaft shown in the figure is proposed as a...Ch. 11 - Repeat the requirements of Prob. 11-29 for the...Ch. 11 - Shown in the figure is a gear-driven squeeze roll...Ch. 11 - The figure shown is a geared countershaft with an...Ch. 11 - The figure is a schematic drawing of a...Ch. 11 - A gear-reduction unit uses the countershaft...Ch. 11 - The worm shaft shown in part a of the figure...Ch. 11 - In bearings tested at 2000 rev/min with a steady...Ch. 11 - A 16-tooth pinion drives the double-reduction...Ch. 11 - Estimate the remaining life in revolutions of an...Ch. 11 - The same 02-30 angular-contact ball bearing as in...Ch. 11 - A countershaft is supported by two tapered roller...Ch. 11 - For the shaft application defined in Prob. 3-74,...Ch. 11 - For the shaft application defined in Prob. 3-76,...Ch. 11 - Prob. 43PCh. 11 - The gear-reduction unit shown has a gear that is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A self-aligning ball bearing used in the car manufacturing industry has a basic dynamic load rating of 26699 N. The desired life of the bearing is 1954 millions of revolutions. Calculate the equivalent dynamic load on the bearing in N. For ball bearing, the value of k is 3.arrow_forwardEstimate the life in hours of a 02-30 mm angular-contact ball bearing subjected to 20,000 revolutions per cycle. Each cycle consists of a radial load of 15 kN for 6 min, and then a change in load to 25.05 kN for 4 min. Determine the expected life of the bearing, in millions of revolutions, for each load, assuming the bearing has a C10 value of 20.3 kN. The expected life of the bearing for 15 kN load is ___ × 106 revolutions.  The expected life of the bearing for 25.05 kN load is ____× 106 revolutions.arrow_forwardSelect a doubler row deep groove ball bearing for a radial load of 5000 N and an axial load of 6000 N, operating at a speed of 1600 r.p.m. for an average life of 8 years at 20 hours per week. Assume W /C0 = 0.50arrow_forward
- A ball bearing that has a life of 12000 hours will carry a radial load of 34 kN. If you studyIf the speed is 1200 rpm, what is the minimum value of the dynamic load number that this bearing should have.is kN?arrow_forwardA propeller shaft rotating at constant speed is subjected to variable loads.Ball bearing supporting the shaft are subject to variable radial loads as follows;16KN for 40 percent of the time,2KN for 10 percent of the time,4KN for 20percent of the time and no load for the remaining time of the cycle.The total life expected for bearing is 3×10^6 revolution at a liability of 94 percent.select the bearing by calculating; a)Net dynamic load for the bearing b)load rating of the bearing from the manufacturers cataloguearrow_forwardA 02-series single-row deep-groove ball bearing is to be selected from Table 11–2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr = 8 kN, axial load Fa = 2 kN, design life LD = 2.40(108), ring rotation factor V = 1, and reliability RD = 0.98. Assuming that the values taken from Table 11–1 are X = 0.56 and Y = 1.63, determine the equivalent radial load rating for this application. What is the equivalent radial load rating for this application in kN?arrow_forward
- Outer and Inner diameter of a thrust bearing are 320 mm and 200 mm respectively . Axial load is 80 kN and pressure is 350 kN / m² . The number of collars required isarrow_forwardA ball bearing with a dynamic load capacity of 22.8 kN is subjected to a radial load of 29kN. Calculate (i) the expected life in million revolutions that 90% of the bearings will reach; (ii) the corresponding life in hours, if the shaft is rotating at 1450 rpm; and (iii) the life that 50% of the bearings will complete or exceed before fatigue failure.arrow_forwardA rolling contact bearing is subjected to the following work cycle: (a) Radial load of 6000 N at 150 r.p.m. for 25% of the time; (b) Radial load of 7500 N at 600 r.p.m. for 20% of the time; and (c) Radial load of 2000 N at 300 r.p.m. for 55% of the time. The inner ring rotates and loads are steady. Select a bearing for an expected average life of 2500 hours.arrow_forward
- An 02-seris single-row deep-groove ball bearing with a 90 mm bore (C0 = 62 kN, C10 = 95.6 kN) is loaded with a 4.34 kN axial load and a 10 kN radial load. The inner ring rotates at 600 rpm (v=1). What is the FaC0? Should X1/Y1 or X2/Y2 be used to caculate the equivalent radial load? Determine the equivalent radial load experienced by this bearing. What is the bearing’s in-use reliability, assuming a design life of 2*10^8 revolutions and an application factor of 1.2?arrow_forward.........A shaft rotating at 150 rpm is subjected to variable load: 8 kN during 60% of the time and 2 kN during 40% of the time. Calculate the basic dynamic load rating in kN for the roller bearing (k = 10/3) for 7200 hours of operation with not more than 10% failures.arrow_forwardA ball bearing operating at a load F has 8000 hours of life. What is the life of the bearing, in hours, when the load is d doubled to 2F?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License