Automotive Technology (Custom)
6th Edition
ISBN: 9781337495356
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 12, Problem 13RQ
Multiple valve engines tend to be more efficient than two-valve-per-cylinder engines because they.
- allow for increased port areas
d. all of the above
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
The most popular combustion chamber.7
which is equipped with four valves per
:cylinder is
Hemispherical Head O
Wedge Chamber
Pent-roof head
.Bath-tube head
„All of the above
It is important to have sufficient turbulence.8
motion in order to
Speed evaporation of the fuel
„Enhance air-fuel mixing
Increase combustion speed and
efficiency
Reduce the time for auto-ignition to
.occur
All of the above
is it true that an l head engine has the intake and exhaust valves mounted in the cylinder head
Briefly explain a 2 and 4 stroke Engines and how each operation.
Chapter 12 Solutions
Automotive Technology (Custom)
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - Prob. 8RQCh. 12 - To ensure proper seating of the valve, the valve...Ch. 12 - When checking valve fit, contact between the valve...
Ch. 12 - If the valve face and valve seat do not contact...Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - Which of the following statements is not true?...Ch. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - When fitting a freshly ground valve into a freshly...Ch. 12 - Technician A says off-square springs may cause...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - Technician A uses a 30-degree stone for topping a...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following are not typically found in the block of a modern engine? a. Pistons b. Crankshaft c. Valves d. Oil pumparrow_forwardList out the design requirements of diesel engine combustion chamberarrow_forwardCam bearings in OHV engines are typically whichtype?a. Split insertb. Full-roundc. Thrustd. None of the abovearrow_forward
- Discuss the main functions of the lubricating system of an enginearrow_forwardHow many degrees the crankshaft will rotate with both the intake and exhaust valves seated when the intake opens 20 deg. BTDC, the exhaust opens 55 deg. BBDC, intake closes 25 deg. ABDC, and exhaust closes 45 deg. ATDC. (TYPE NUMBERS ONLY, AND THE UNIT IS DEG. AND ANSWER IN WHOLE NUMBERS ONLY) * Your answer On a four-stroke cycle reciprocating engine, which strokes are both valves open? * Power Compression Intake Exhaust Ignition The primary concern in the firing order of the opposed engine is to keep the power impulses on adjacent cylinders as close as possible to obtain the most outstanding mechanical efficiency. TRUE OR FALSE? * Your answer A nine-cylinder engine with a bore of 5.5 inches and a stroke of 6 inches will have a total piston displacement of? (TYPE NUMBERS ONLY, AND THE UNIT IS CU. INCH AND ANSWER IN WHOLE NUMBERS ONLY) * Your answerarrow_forwardBriefly explain the determination of gas pressure excitations in a 4-stroke engine.arrow_forward
- Explain the benefit of using 4 valves per cylinder (2 Intake and 2 exhaust) instead of 2 valves per cylinder (1 intake and 1 exhaust)arrow_forwardWrite short note on engine capacityarrow_forward2- What is normal air flow rate? How is air flow pressure measured? 4- Which engine produces the most torque (diesel or petrol)? why? 5- Mention the air fuel ratio required by the engine during (a) Starting time zero load (b) Normal running half load (C)full load 6- Types of lubrication in an IC engine?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY