![Automotive Technology (Custom)](https://www.bartleby.com/isbn_cover_images/9781337495356/9781337495356_largeCoverImage.gif)
Automotive Technology (Custom)
6th Edition
ISBN: 9781337495356
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 12, Problem 5ASRQ
Technician A says off-square springs may cause increased stem-to-guide wear. Technician B says excessive spring tension may cause premature camshaft wear. Who is correct?
- Technician A
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
Technician A says that vacuum readings for an engine with a performance camshaft might be lower at
idle. Technician B says that an engine that has worn lower main bearing will have lower oil pressure at
freeway/highway speeds.
Who is correct?
Technician A only
Technician B only
Both A and B
O Neither A nor B
List six checks that should be carried out when inspecting camshafts
Q1- Explain the duties of camshaft, distributor and alternator, which are among the engine parts
Chapter 12 Solutions
Automotive Technology (Custom)
Ch. 12 - Explain staged and continuously variable value...Ch. 12 - Define valve margin.Ch. 12 - What usually causes warpage in an aluminum cylin...Ch. 12 - What are the two ways pushrods can be checked for...Ch. 12 - Which of the following is not true of knurling? It...Ch. 12 - True False? Fiats MultiAir system relies on...Ch. 12 - To allow the engine to run on the Atkinson cycle,...Ch. 12 - Prob. 8RQCh. 12 - To ensure proper seating of the valve, the valve...Ch. 12 - When checking valve fit, contact between the valve...
Ch. 12 - If the valve face and valve seat do not contact...Ch. 12 - Many engines with WT have a phaser mounted to the...Ch. 12 - Multiple valve engines tend to be more efficient...Ch. 12 - Which of the following is not a type of valve...Ch. 12 - Which of the following statements is not true?...Ch. 12 - While discussing the reasons for resurfacing a...Ch. 12 - While inspecting the timing gears of an engine:...Ch. 12 - Technician A says that positive valve stem seals...Ch. 12 - When fitting a freshly ground valve into a freshly...Ch. 12 - Technician A says off-square springs may cause...Ch. 12 - Technician A says it is not necessary to measure...Ch. 12 - Technician A uses a 30-degree stone for topping a...Ch. 12 - While discussing the Valvetronic system:...Ch. 12 - While checking a hydraulic phaser after the...Ch. 12 - While servicing a pair of aluminum cylinder heads:...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing camshafts Technician A says valve lift is based only on the height of the cam lobe. Technician B says valve duration is based on the height of the lobe. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTrue False? Camshaft straightness is checked using V-blocks and a feeler gauge?arrow_forwardWhile diagnosing the cause for an engine having good results from a compression test and cylinder leakage test but poor results from a cylinder power balance test: Technician A says that incorrect valve timing is the most likely cause. Technician B says that a severely worn cam lobe is a likely cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8 engine of the same displacement. Technician B says that there are twice as many teeth on the crankshaft as there are on the camshaft sprocket. Who is correct? and why? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that delayed shifting can be caused by worn planetary gearset members. Technician B says that delayed shifts or slippage may be caused by leaking hydraulic circuits or sticking spool valves in the valve body. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhat is the main difference between a crankshaft and a cam shaftarrow_forward
- Tech a says that the push on the piston top during the power stroke is transferred to the crank shaft through the connecting rod. Tech b states that the power is transferred from the piston through the valve train to the camshaft. Who is correct?arrow_forwardWhile discussing a pressure test: Technician A says that this test is the most valuable diagnostic check for slippage when a gear is engaged. Technician B says that the test can identify the cause of late or harsh shifting. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhen removing the balance shaft assembly: tech a inspects the bearings for unusual wear or damage. Tech b smoothens a damaged camshaft or balance shaft journal by lightly sanding it. Who is correct?arrow_forward
- While installing a timing belt: Technician A installs the belt, turns the crankshaft two full rotations, then applies tension to the belt. Technician B installs the belt, applies tension, then turns the crankshaft two full rotations. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardAfter installing cam bearings: Technician A checks that the oi, holes in the bearings are properly aligned with those in the block by squirting oil into the holes. Technician B checks for proper alignment by inserting a wire through the holes. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhich of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
![Text book image](https://www.bartleby.com/isbn_cover_images/9781133612315/9781133612315_smallCoverImage.gif)
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781337794213/9781337794213_smallCoverImage.jpg)
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License