Fundamentals of Physics, Volume 1, Chapter 1-20
10th Edition
ISBN: 9781118233764
Author: David Halliday
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 12, Problem 26P
GO In Fig. 12-43, a climber leans out against a vertical ice wall that has negligible friction. Distance a is 0.914 m and distance L is 2.10 m. His center of mass is distance d = 0.940 m from the feet–ground contact point. If he is on the verge of sliding, what is the coefficient of static friction between feet and ground?
Figure 12-43 Problem 26.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
In the wood industries, inclined blocks of wood are sometimes used to determine the compression-shear strength of glued joints. Consider the pair of glued blocks A and B in Figure which are 38 mm deep in a direction perpendicular to the plane of the paper. Determine the shearing ultimate strength of the glue in MPa if a vertical force of 50 kN is required to cause rupture of the joint.
A 1.2-m plank of mass 3 kg rests on two joists. Knowing that the coefficient of static friction between the plank and the joists is 0.30,determine the magnitude of the horizontal force required to move the plank when (a) a= 750 mm, (b) a = 900 mm.
A 200-lb man walks up an inclined plank of negligible weight which makes an angle of 70o with the wall. The coefficient of static friction between the floor and the ladder is 0.3 and that between the ladder and the wall is 0.2. When the man is at a horizontal distance X from the foot of the plank, the plank would begin toslide.
(a) Draw a complete FBD of the system.
Find (b) the frictional force on the floor, and the frictional force on the wall and
(c) the horizontal distance X.
Chapter 12 Solutions
Fundamentals of Physics, Volume 1, Chapter 1-20
Ch. 12 - Figure 12-15 shows three situations in which the...Ch. 12 - In Fig, 12-16, a rigid beam is attached to two...Ch. 12 - Figure 12-17 shows four overhead views of rotating...Ch. 12 - A ladder leans against a frictionless wall but is...Ch. 12 - Figure 12-18 shows a mobile of toy penguins...Ch. 12 - Figure 12-19 shows an overhead view of a uniform...Ch. 12 - In Fig. 12-20, a stationary 5 kg rod AC is held...Ch. 12 - Three piatas hang from the stationary assembly of...Ch. 12 - In Fig. 12-22, a vertical rend is hinged at its...Ch. 12 - Figure 12-23 shows a horizontal block that is...
Ch. 12 - The table gives the initial lengths of three reds...Ch. 12 - A physical therapist gone wild has constructed the...Ch. 12 - Prob. 1PCh. 12 - An automobile with a mass of 1360 kg has 3.05 m...Ch. 12 - SSM WWWIn Fig. 12-26, a uniform sphere of mass m =...Ch. 12 - An archers bow is drawn at its midpoint until the...Ch. 12 - ILWA rope of negligible mass is stretched...Ch. 12 - A scaffold of mass 60 kg and Length 5.0 m is...Ch. 12 - A 75 kg window cleaner uses a 10 kg ladder that is...Ch. 12 - A physics Brady Bunch, whose weights in newtons...Ch. 12 - SSMA meter stick balances horizontally on a...Ch. 12 - GO The system in Fig. 12-28 is in equilibrium,...Ch. 12 - SSMFigure 12-29 shows a diver of weight 580 N...Ch. 12 - In Fig. 12-30, trying to gel his car out of mud, a...Ch. 12 - Figure 12-31 shows the anatomical structures in...Ch. 12 - In Fig. 12-32, a horizontal scaffold, of length...Ch. 12 - ILWForces F1, F2 and F3 act on the structure of...Ch. 12 - A uniform cubical crate is 0.750 m on each side...Ch. 12 - In Fig. 12-34, a uniform beam of weight 500 N and...Ch. 12 - GO In Fig. 12-35, horizontal scaffold 2, with...Ch. 12 - To crack a certain nut in a nutcracker, forces...Ch. 12 - A bowler holds a bowling ball M = 7.2 kg in the...Ch. 12 - ILWThe system in Fig. 12-38 is in equilibrium. A...Ch. 12 - GO In Fig-12-39, a 55 kg rock climber is in a...Ch. 12 - GO In Fig. 12-40, one end of a uniform beam of...Ch. 12 - GO In Fig. 12-41, a climber with a weight of 533.8...Ch. 12 - SSM WWWIn Fig. 12-42, what magnitude of constant...Ch. 12 - GO In Fig. 12-43, a climber leans out against a...Ch. 12 - GO In Fig. 12-44, a 15 kg block is held in place...Ch. 12 - GO In Fig. 12-45, suppose the length L of the...Ch. 12 - A door has a height of 2.1 m along a y axis that...Ch. 12 - GO In Fig. 12-46, a 50.0 kg uniform square sign,...Ch. 12 - GO In Fig. 12-47, a nonuniform bar is suspended at...Ch. 12 - In Fig. 12-48, the driver of a car on a horizontal...Ch. 12 - Figure 12-49a shows a vertical uniform beam of...Ch. 12 - In Fig. 12-45, a thin horizontal bar AB of...Ch. 12 - SSM WWWA cubical box is filled with sand and...Ch. 12 - Figure 12-50 shows a 70 kg climber hanging by only...Ch. 12 - GO In Fig. 12-51, a uniform plank, with a length L...Ch. 12 - In Fig, 12-52, uniform beams A and B are attached...Ch. 12 - For the stepladder shown in Fig. 12-53, sides AC...Ch. 12 - Figure 12-54a shows a horizontal uniform beam of...Ch. 12 - A crate, in the form of a cube with edge lengths...Ch. 12 - In Fig. 12-7 and the associated sample problem,...Ch. 12 - SSM ILWA horizontal aluminum rod 4.8 cm in...Ch. 12 - Figure 12-55 shows the stressstrain curve for a...Ch. 12 - In Fig. 12-56, a lead brick rests horizontally on...Ch. 12 - Figure 12-57 shows an approximate plot of stress...Ch. 12 - A tunnel of length L = 150 m, height H = 7.2 m,...Ch. 12 - Figure 12-59 shows the stress versus strain plot...Ch. 12 - GO In Fig. 12-60, a 103kg uniform log hangs by two...Ch. 12 - GO Figure 12-61 represents an insect caught at the...Ch. 12 - GO Figure 12-62 is an overhead view of a rigid rod...Ch. 12 - After a fall, a 95 kg rock climber finds himself...Ch. 12 - SSMIn Fig 12-63, a rectangular slab of slate rests...Ch. 12 - A uniform ladder whose length is 5.0 m and whose...Ch. 12 - SSM In Fig. 12-64, block A mass 10 kg is in...Ch. 12 - Figure 12-65a shows a uniform ramp between two...Ch. 12 - GO In Fig. 12-66, a 10 kg sphere is supported on a...Ch. 12 - In Fig. 12-67a, a uniform 40.0 kg beam is centered...Ch. 12 - SSM In Fig. 12-68, an 817 kg construction bucket...Ch. 12 - In Fig. 12-69, a package of mass m hangs from a...Ch. 12 - ILWThe force F in Fig. 12-70 keeps the 6.40 kg...Ch. 12 - A mine elevator is supported by a single steel...Ch. 12 - Four bricks of length L, identical and uniform,...Ch. 12 - Prob. 64PCh. 12 - In Fig. 12-73, a uniform beam with a weight of 60...Ch. 12 - A uniform beam is 5.0 m long and has a mass of 53...Ch. 12 - A solid copper cube has an edge length of 85.5 cm....Ch. 12 - A construction worker attempts to lift a uniform...Ch. 12 - SSM In Fig. 12-76, a uniform rod of mass m is...Ch. 12 - A 73 kg man stands on a level bridge of length L....Ch. 12 - SSMA uniform cube of side length 8.0 cm rests cm a...Ch. 12 - The system in Fig. 12-77 is in equilibrium. The...Ch. 12 - SSMA uniform ladder is 10 m long and weighs 200 N....Ch. 12 - A pan balance is made up of a rigid, massless rod...Ch. 12 - The rigid square frame in Fig. 12-79 consists of...Ch. 12 - A gymnast with mass 46.0 stands on the end of a...Ch. 12 - Figure 12-81 shows a 300 kg cylinder that is...Ch. 12 - In Fig. 12-82, a uniform beam of length 12.0 m is...Ch. 12 - Four bricks of length L, identical and uniform,...Ch. 12 - A cylindrical aluminum rod, with an initial length...Ch. 12 - Prob. 81PCh. 12 - If the square beam in Fig. 12-6a and the...Ch. 12 - Figure 12-84 shows a stationary arrangement of two...Ch. 12 - A makeshift swing is constructed by makings loop...Ch. 12 - Figure 12-85a shows details of a finger in the...Ch. 12 - A trap door in a ceiling is 0.91 m square, has a...Ch. 12 - A particle is acted on by forces given, in...Ch. 12 - The leaning Tower of Pisa is 59.1 m high and 7.44...
Additional Science Textbook Solutions
Find more solutions based on key concepts
A 2.2-nF capacitor and one of unknown capacitance are in parallel across a 10-V rms sine-wave generator. At 1.0...
Essential University Physics: Volume 2 (3rd Edition)
Explain all answers clearly, with complete sentences and proper essay structure, if needed. An asterisk (*) des...
Cosmic Perspective Fundamentals
angle above the horizontal. The other end of the rope is attached to the front of the first of two wagons that ...
College Physics
In a sink, 5 L of water at 70°C is combined with 1 kg of aluminum pots, 1 kg of silverware (steel), and 1 kg of...
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
Answer the following questions for the position of the Moon shown in Figure 1.
Which Moon phase would an Earth...
Lecture- Tutorials for Introductory Astronomy
2.20 BIO Blackout? A jet fighter pilot wishes to accelerate from rest at a constant acceleration of 5g to reach...
University Physics (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- 11-30 Two blocks are suspended on a continuous inex- tensible cord as shown in Fig. P11-30. Determine the angle O for equilibrium if the masses of blocks A and B are 50 and 40 kg, respectively. Fig. P11-30arrow_forwardA 20 kg ladder leans against a vertical wall with an angle of 20°. Determine the static friction at the foot of the ladder.arrow_forward11-13arrow_forward
- a 8-53.. A lantern of weight W is suspended at the end horizontal bar of weight w and length L that is supported by a cable that makes an angle with the side of a vertical wall. Assume the weight of the bar is at its center. (a) Derive an equation for the tension in the cable. (b) Calculate the tension in the cable for a bar of weight 28 N and length 1.5 m, plus a lantern of weight 85 N, and the cable making a 37° angle to the vertical. 40² Darrow_forwardChapter 12, Problem 028 GO In the figure, suppose the length L of the uniform bar is 3.1 m and its weight is 240 N. Also, let the block's weight W = 270 N and the angle e = 41°. The wire can withstand a maximum tension of 420 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? Com (a) Number Units (b) Number Units (c) Number Unitsarrow_forwardA deli owner creates a lunch special display board by taking a uniform board which has a weight of 122 N, cutting it in half, hinging the halves together with a frictionless hinge, and setting it up as an inverted "V". Determine the minimum coefficient of static friction needed between the board and the ground in order for her to set the display board up with an angle of 30° between the two sides. 30°arrow_forward
- Chapter 12, Problem 028 GO In the figure, suppose the length L of the uniform bar is 2.7 m and its weight is 220 N. Also, let the block's weight W = 280 N and the angle 0 = 27°. The wire can withstand a maximum tension of 440 N. (a) What is the maximum possible distance x before the wire breaks? With the block placed at this maximum x, what are the (b) horizontal and (c) vertical components of the force on the bar from the hinge at A? com A (a) Number Units (b) Number Units (c) Number Units Click if you would like to Show Work for this question: Open Show Workarrow_forwardB 30° A The 50 kg homogeneous smooth sphere rests on the 30 degree incline A and bears against the smooth vertical wall B. Determine: Magnitude of Contact force at A (in N) round off to two (2) decimal places answer range: +/- 0.05 unitsarrow_forwardA rigid bar of mass M is supported symmetrically by three wires each of length l. Those at each end are ofcopper and the middle one is of iron. The ratio of their diameter, if each is to have the same tension, is equal to (a)YcopperYiron(b) √YironY copper(c)Yiron2Ycopper2(d)YironYcopperarrow_forward
- Two identical, uniform beams are symmetrically set up against each other (Fig. 9–87) on a floor with which they have a coefficient of fric- tion µs = 0.50. What is the minimum angle the beams can make with the floor and still not fall? FIGURE 9-87 Problem 71.arrow_forwardThe 35-kg homogeneous smooth sphere rests on the 28° incline A and bears against the smooth vertical wall B. Calculate the contact force at A and B. Assume = 28% Ꮎ Answers: FA= FB = i i B N Narrow_forward2) A student’s head is bent over her physics book. The head weighs P = 24.6 N and is supported by the muscle force F→mF→m exerted by the neck extensor muscles and by the contact force F→cF→c exerted at the atlantooccipital joint. Given that the magnitude of F→mF→m is 60.0 N and is directed 35.0° below the horizontal. a.) Find the magnitude of the contact force F→cF→c . b.)Find the direction of the contact force Fc−→Fc→ . If the direction is below the horizontal, enter a negative value.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- College PhysicsPhysicsISBN:9781305952300Author:Raymond A. Serway, Chris VuillePublisher:Cengage LearningUniversity Physics (14th Edition)PhysicsISBN:9780133969290Author:Hugh D. Young, Roger A. FreedmanPublisher:PEARSONIntroduction To Quantum MechanicsPhysicsISBN:9781107189638Author:Griffiths, David J., Schroeter, Darrell F.Publisher:Cambridge University Press
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningLecture- Tutorials for Introductory AstronomyPhysicsISBN:9780321820464Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina BrissendenPublisher:Addison-WesleyCollege Physics: A Strategic Approach (4th Editio...PhysicsISBN:9780134609034Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart FieldPublisher:PEARSON
College Physics
Physics
ISBN:9781305952300
Author:Raymond A. Serway, Chris Vuille
Publisher:Cengage Learning
University Physics (14th Edition)
Physics
ISBN:9780133969290
Author:Hugh D. Young, Roger A. Freedman
Publisher:PEARSON
Introduction To Quantum Mechanics
Physics
ISBN:9781107189638
Author:Griffiths, David J., Schroeter, Darrell F.
Publisher:Cambridge University Press
Physics for Scientists and Engineers
Physics
ISBN:9781337553278
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
Lecture- Tutorials for Introductory Astronomy
Physics
ISBN:9780321820464
Author:Edward E. Prather, Tim P. Slater, Jeff P. Adams, Gina Brissenden
Publisher:Addison-Wesley
College Physics: A Strategic Approach (4th Editio...
Physics
ISBN:9780134609034
Author:Randall D. Knight (Professor Emeritus), Brian Jones, Stuart Field
Publisher:PEARSON
Static Equilibrium: concept; Author: Jennifer Cash;https://www.youtube.com/watch?v=0BIgFKVnlBU;License: Standard YouTube License, CC-BY