Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 12, Problem 31P
Compute the air density in the undisturbed air and at the stagnation point of an aircraft flying at 250 m/s in air at 28 kPa and 250°C. What is the percentage increase in density? Can we approximate this as an incompressible flow?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
show that the governing equation for axisymmetric stagnation flow is ϕ ′′′ + 2ϕϕ′′ − ϕ ′2 + 1 = 0 what is the thickness of viscous layer near the axisymmetric stagnation point?
An aircraft is designed to cruise at Mach number Ma = 1.1 at 12,000 m where the atmospheric temperature is 236.15 K. Determine the stagnation temperature on the leading edge of the wing.
Consider an equimolar mixture of oxygen and nitrogen. Determine the critical temperature, pressure, and density for stagnation temperature and pressure of 550 K and 350 kPa.
Chapter 12 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 12 - Air is expanded in a steady flow process through a...Ch. 12 - Five kilograms of air is cooled in a closed tank...Ch. 12 - Air is contained in a piston-cylinder device. The...Ch. 12 - Calculate the power delivered by the turbine per...Ch. 12 - If hydrogen flows as a perfect gas without...Ch. 12 - A 1-m3 tank contains air at 0.1 MPa absolute and...Ch. 12 - Air enters a turbine in steady flow at 0.5 kg/s...Ch. 12 - Natural gas, with the thermodynamic properties of...Ch. 12 - Carbon dioxide flows at a speed of 10 m/s in a...Ch. 12 - In an isothermal process, 0.1 cubic feet of...
Ch. 12 - Calculate the speed of sound at 20C for (a)...Ch. 12 - An airplane flies at 550 km/hr at 1500 m altitude...Ch. 12 - Actual performance characteristics of the Lockheed...Ch. 12 - For a speed of sound in steel of 4300 m/s,...Ch. 12 - Determine and plot the Mach number of an...Ch. 12 - Investigate the effect of altitude on Mach number...Ch. 12 - The grandstand at the Kennedy Space Center is...Ch. 12 - Use data for specific volume to calculate and plot...Ch. 12 - An object traveling in atmospheric air emits two...Ch. 12 - An object traveling in atmospheric air emits two...Ch. 12 - While at the seashore, you observe an airplane...Ch. 12 - The temperature varies linearly from sea level to...Ch. 12 - Prob. 23PCh. 12 - A photograph of a bullet shows a Mach angle of 32....Ch. 12 - An F-4 aircraft makes a high-speed pass over an...Ch. 12 - All aircraft passes overhead at 3 km altitude. The...Ch. 12 - A supersonic aircraft flies at 3 km altitude at a...Ch. 12 - For the conditions of Problem 12.27, find the...Ch. 12 - The Concorde supersonic transport cruised at M =...Ch. 12 - Plot the percentage discrepancy between the...Ch. 12 - Compute the air density in the undisturbed air and...Ch. 12 - Carbon dioxide flows in a duct at a velocity of 90...Ch. 12 - If nitrogen at 15C is flowing and the stagnation...Ch. 12 - An aircraft cruises at M = 0.65 at 10 km altitude...Ch. 12 - High-speed aircraft use air data computers to...Ch. 12 - A supersonic wind tunnel test section is designed...Ch. 12 - Oxygen flows in a passage at a pressure of 25...Ch. 12 - What is the pressure on the nose of a bullet...Ch. 12 - Prob. 39PCh. 12 - Air flows in an insulated duct. At point the...Ch. 12 - Consider steady, adiabatic flow of air through a...Ch. 12 - Air passes through a normal shock in a supersonic...Ch. 12 - A Boeing 747 cruises at M = 0:87 at an altitude of...Ch. 12 - Space debris impact is a real concern for...Ch. 12 - A CO2 cartridge is used to propel a toy rocket....Ch. 12 - Nitrogen flows from a large tank, through a...Ch. 12 - Air flows from the atmosphere into an evacuated...Ch. 12 - Oxygen discharges from a tank through a convergent...Ch. 12 - The hot gas stream at the turbine inlet of a JT9-D...Ch. 12 - Carbon dioxide discharges from a tank through a...Ch. 12 - Air at 100F and 100 psia in a large tank flows...Ch. 12 - Calculate the required diameter of a convergent...Ch. 12 - Steam flows steadily and isentropically through a...Ch. 12 - Nitrogen flows through a diverging section of duct...Ch. 12 - At a section in a passage, the pressure is 30...Ch. 12 - In a given duct flow M = 2.0; the velocity...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Five pounds of air per second discharge from a...Ch. 12 - Air flows isentropically through a...Ch. 12 - Air, at an absolute pressure of 60.0 kPa and 27C,...Ch. 12 - Carbon dioxide flows from a tank through a...Ch. 12 - A convergent-divergent nozzle of 50-mm tip...Ch. 12 - Air flows adiabatically through a duct. At the...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Atmospheric air at 98.5 kPa and 20C is drawn into...Ch. 12 - The exit section of a convergent-divergent nozzle...Ch. 12 - Air flowing isentropically through a converging...Ch. 12 - Air flows from a large tank at p = 650 kPa...Ch. 12 - A converging nozzle is connected to a large tank...Ch. 12 - Air at 0C is contained in a large tank on the...Ch. 12 - A large tank initially is evacuated to 10 kPa...Ch. 12 - Air flows isentropically through a converging...Ch. 12 - Air enters a converging-diverging nozzle at 2 MPa...Ch. 12 - Prob. 75PCh. 12 - A jet transport aircraft, with pressurized cabin,...Ch. 12 - A converging-diverging nozzle, with a throat area...Ch. 12 - Air, at a stagnation pressure of 7.20 MPa absolute...Ch. 12 - A small rocket motor, fueled with hydrogen and...Ch. 12 - Testing of a demolition explosion is to be...Ch. 12 - A total-pressure probe is placed in a supersonic...Ch. 12 - Air flows steadily through a long, insulated...Ch. 12 - Air discharges through a convergent-divergent...Ch. 12 - A normal shock wave exists in an airflow. The...Ch. 12 - Air approaches a normal shock at V1 = 900 m/s, p1...Ch. 12 - Air approaches a normal shock at M1 = 2.5, with...Ch. 12 - Air undergoes a normal shock. Upstream, T1 = 35C,...Ch. 12 - If, through a normal shock wave in air, the...Ch. 12 - The stagnation temperature in an airflow is 149C...Ch. 12 - A supersonic aircraft cruises at M = 2.2 at 12 km...Ch. 12 - The Concorde supersonic transport flew at M = 2.2...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Determine the reactions at the supports. Prob. 4-6
Statics and Mechanics of Materials (5th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
3.24 Compute the moment about point A for the linkage shown.
Applied Statics and Strength of Materials (6th Edition)
A 100 ft length of buried, uninsulated steel pipe carries chilled water at a mean temperature of 42 F. The pipe...
Heating Ventilating and Air Conditioning: Analysis and Design
The force in each member of truss and the state of members are in tension or compression.
Engineering Mechanics: Statics & Dynamics (14th Edition)
Figure 28.11 showed residual stress distributions produced by surface grinding. What is a residual stress?
Degarmo's Materials And Processes In Manufacturing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A subsonic airplane is flying at a 5000-m altitude where the atmospheric conditions are 54 kPa and 256 K. A Pitot static probe measures the difference between the static and stagnation pressures to be 16 kPa. Calculate the speed of the airplane and the flight Mach number.arrow_forwardA normal shock produced by an explosion propagate at a constant velocity of 450 m/s into still air of 100 kPa and 23 °C. The ratio of stagnation pressure upstream the shock to stagnation pressure of the gas flow behind the wave isarrow_forwardAir is to be expanded to Mach 2.2 in a converging-diverging nozzle from an inlet velocity of 90 m/s. The inlet area is 50 cm2 and the inlet static temperature is 600 K. Assuming isentropic flow, determine the throat and exit areas required.arrow_forward
- Is it possible to accelerate a fluid to supersonic velocities with a velocity other than the sonic velocity at the throat? Explainarrow_forwardAn aircraft is flying at supersonic speed. At a component of an aircraft where the flow is perpendicular (normalshock), the density ratio is 5. Solve for: a.Mach Number Downstream b. Pressure Ratio c. Temperature Ratio d. Mach Number upstreamarrow_forwardRace cars at the Indianapolis Speedway average speeds of185 mi/h. After determining the altitude of Indianapolis,fi nd the Mach number of these cars and estimate whethercompressibility might affect their aerodynamics.arrow_forward
- Starting with the differential form of the energy equation, show that the flow velocity increases with heat addition in subsonic Rayleigh flow, but decreases in supersonic Rayleigh flow.arrow_forwardShock waves are treated as discontinuities here, but theyactually have a very small fi nite thickness. After giving itsome thought, sketch your idea of the distribution of gasvelocity, pressure, temperature, and entropy through theinside of a shock wave.arrow_forward1 atm = 2116 lb/ft2 = 1.01 × 105 N/m2. The temperature and pressure at the stagnation point of a high-speedmissile are 934 ◦R and 7.8 atm, respectively. Calculate the density at thispoint.arrow_forward
- A gas at a specified stagnation temperature and pressure is accelerated to Ma = 2 in a converging–diverging nozzle and to Ma = 3 in another nozzle. What can you say about the pressures at the throats of these two nozzlesarrow_forwardConsider a typical air flow around a cruising jetliner at 10km altitude. The speed is now 810 km/h, while the ambient conditions are 0.414 kg/m³ , 0.261 atm and -50°C. At the stagnation point, the temperature rises over by 25°C, while the density and pressure changes by more than 30% and 45 % respectively. Classify the following situations as compressible/incompressible flowarrow_forwardConsider supersonic Fanno flow that is decelerated to sonic velocity (Ma = 1) at the duct exit as a result of frictional effects. If the duct length is increased further, will the flow at the duct exit be supersonic, subsonic, or remain sonic? Will the mass flow rate of the fluid increase, decrease, or remain constant as a result of increasing the duct length?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License