Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 13, Problem 1ASRQ
To determine
Technician A says that TTY bolts can be used after they were removed if there are no signs of distortion or stretching. Technician B says that head bolts that pass through a coolant passage should be coated with a nonhardening sealer prior to installing them. Who is correct?
a. Technician A.
b. Technician B.
c. Both A and B.
d. Neither A nor B.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt may become fatigued if it is under tightened. Who is correct?
The three major types of rubber seals used in automatic transmission are the blank the blank and the blank
Hydraulic hose couplings do not seal on their connecting threads. They seal on the mating of two surfaces (male & female). What is the common seal angle of these surfaces?
47 degrees
23 degrees
None of these
37 degrees
Varies by tube diameter
Chapter 13 Solutions
Automotive Technology
Ch. 13 - What are the major differences between aerobic and...Ch. 13 - How does a torque-to-yield bolt differ from...Ch. 13 - How do seals differ from gaskets?Ch. 13 - Where are thread sealers most often used?Ch. 13 - On hybrid vehicles, how can you identify the high...Ch. 13 - True or False? Make sure you locate and adhere to...Ch. 13 - True or False? The computer in most late-model...Ch. 13 - True or False? Some crankshaft and camshaft timing...Ch. 13 - True or False? Valve lash is adjusted in many...Ch. 13 - Which of the following statements is incorrect?...
Ch. 13 - Which of the following statements about the...Ch. 13 - Graphite is. an anaerobic substance an RTV an...Ch. 13 - Which of the following are considered soft, cut...Ch. 13 - What material is typically not used to form a rear...Ch. 13 - Which of the following statements about preparing...Ch. 13 - Prob. 1ASRQCh. 13 - Technician A uses adhesives to hold gaskets in...Ch. 13 - Technician A uses soft gaskets on valve covers....Ch. 13 - While installing a timing belt: Technician A...Ch. 13 - Technician A says that oil pan gaskets are often...Ch. 13 - Prob. 6ASRQCh. 13 - While discussing proper engine break-in:...Ch. 13 - Prob. 8ASRQCh. 13 - Prob. 9ASRQCh. 13 - While selecting the proper RTV for a particular...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing thread sealants and lubricants: Technician A says that antiseize compound is used where a bolt might become difficult to remove after a period of time. Technician B says that thread sealants are used on bolts that are tightened into an oil cavity or coolant passage. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A uses adhesives to hold gaskets in place while installing them. Technician B uses RTV sealant on all surfaces that are prone to leaks. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A inspects all sealing surfaces for damage and uses a supplementary sealant on the gaskets if the surface is questionable. Technician B coats the intake gasket on some engines with a nonhardening sealer. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing the reasons for resurfacing a cylinder head; Technician A says it should be resurfaced to make it flat and very smooth so the head gasket can seal properly during engine assembly. Technician B says that it can be resurfaced to raise the compression. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhat is the most common cause of leaking compression fittings? A. Cracked compression nut B. Overtightening the compression nut C. An improperly sized ring or ferrule D. Both A and C are common causes of fitting leakagearrow_forwardTechnician A says head gasket thickness has an effect on compression ratio. Technician B says connecting rod length has an effect on compression ratio. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says that shock absorbers should be inspected for loose mounting bolts and worn mounting bushings. Technician B says that shock absorbers and struts should be inspected for oil leakage. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing an inoperative blend air door: Technician A says that to check the proper functioning of the ductwork, a scan tool may be used to command the door to change position. Technician B says that in some cases you can reach under the dash to reconnect the cable or free a stuck flap. Who is right? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile discussing the common causes for cracks developing in a cylinder block or head: Technician A says that the chilling of a hot engine by a sudden rush of cold water or air over the surf ace may cause cracking. Technician B says that excessive overheating is a common cause. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Technician A says that portable floor jacks may be operated by hydraulics. Technician B says that portable floor jacks may be operated by compressed air. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? The powdery substance released from the air bag when it is deployed is sodium hydroxide, which can cause skin irritation.arrow_forwardTechnician A says that jack stands should always be used with portable floor jacks. Technician B says lifting capacity and operation should be checked before using a floor jack. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning