EBK LOGIXPRO PLC LAB MANUAL FOR PROGRAM
5th Edition
ISBN: 8220102803503
Author: Petruzella
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Expert Solution & Answer
Chapter 13, Problem 9P
Explanation of Solution
Items to be suspected:
- The fault condition is obtained when an instruction is given and the correct status indication is not showed by the
programming device monitor. - It might be because of the reason that the input module is not converting the input signal into the logic level voltage required by the processor module...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Control registers are quickly explained.
A press's machine cycle is as follows:
;Lowering the ram: the ram is lowered when
The safety screen was open before the cycle began and
is now closed (limit switches S4 and S5 actuated)
The press is in the home, i.e. upper position (limit switch
.S6 actuated)
Two-hand switches S1 and S2 were not actuated prior to
.the cycle but are now
Halting the ram during lowering: the ram stops
;immediately when
One of the two-hand switches is released. Or
The safety screen is opened. Or
.The ram is down (limit switch S3 actuated)
Raising the ram: If the ram is down (limit switch S3 风
actuated), it is raised by the eccentric drive. The safety
.screen can be opened and both two-hand switches released
The machining cycle is completed when the ram reaches the
.home position (limit switch S6 actuated)
The designer needs for
******
state boxes for drawing the ASM-chart for
the controller of the aforementioned system
6
7
9
10
8
5
A press's machine cycle is as follows:
;Lowering the ram: the ram is lowered when 0
The safety screen was open before the cycle began and
is now closed (limit switches S4 and S5 actuated)
The press is in the home, i.e. upper position (limit switch
S6 actuated)
Two-hand switches S1 and S2 were not actuated prior to
the cycle but are now
.
Halting the ram during lowering: the ram stops 0
;immediately when
One of the two-hand switches is released. Or
.
.
The safety screen is opened. Or
.The ram is down (limit switch S3 actuated)
Raising the ram: If the ram is down (limit switch S3
actuated), it is raised by the eccentric drive. The safety
.screen can be opened and both two-hand switches released
The machining cycle is completed when the ram reaches the
home position (limit switch S6 actuated)
The designer needs for ........conditional output boxes for drawing the
ASM-chart for the controller of the aforementioned system
0 C
O O O O O O
Chapter 13 Solutions
EBK LOGIXPRO PLC LAB MANUAL FOR PROGRAM
Ch. 13 - Prob. 1RQCh. 13 - Prob. 2RQCh. 13 - Prob. 3RQCh. 13 - List three potential noise-generating inductive...Ch. 13 - Prob. 5RQCh. 13 - Prob. 6RQCh. 13 - Prob. 7RQCh. 13 - Under what condition can a ground loop circuit be...Ch. 13 - Prob. 9RQCh. 13 - What operating state will cause an inductive load...
Ch. 13 - Prob. 11RQCh. 13 - Prob. 12RQCh. 13 - Prob. 13RQCh. 13 - Prob. 14RQCh. 13 - Prob. 15RQCh. 13 - List four uses for the data monitor function.Ch. 13 - Prob. 17RQCh. 13 - Prob. 18RQCh. 13 - Prob. 19RQCh. 13 - Prob. 20RQCh. 13 - Prob. 21RQCh. 13 - Prob. 22RQCh. 13 - Prob. 23RQCh. 13 - Prob. 24RQCh. 13 - Prob. 25RQCh. 13 - Prob. 26RQCh. 13 - Prob. 27RQCh. 13 - Prob. 28RQCh. 13 - Prob. 29RQCh. 13 - Prob. 30RQCh. 13 - Prob. 1PCh. 13 - A fuse is blown in an output module. Suggest two...Ch. 13 - Prob. 3PCh. 13 - Prob. 4PCh. 13 - Prob. 5PCh. 13 - Prob. 6PCh. 13 - A specific output is forced on, but the LED module...Ch. 13 - An electronic-based input sensor is wired to a...Ch. 13 - Prob. 9PCh. 13 - Prob. 11PCh. 13 - Prob. 12PCh. 13 - Prob. 13PCh. 13 - The program of Figure 13-39 is supposed to execute...
Knowledge Booster
Similar questions
- please explain the Processing an Interrupt figurearrow_forwardAssembly Language Design the program for a heater controller. When the program first starts, the heater should be turned off. The thermometer is connected to port 1 and the heater to port 2. If the thermometer has a value of less than 64, turn the heater on. If the value is 64 or more, turn the heater off. Use subroutines to turn the heater on and off. The program should loop continuously. The heater is turned on by setting bit 3 to 1. It is turned off by setting the bit to 0.arrow_forwardDescribe how the clocking procedure works.arrow_forward
- Accessing the system timer is a privileged instruction. True Falsearrow_forwardDescribe the clocking procedure.arrow_forwardA press's machine cycle is as follows: c) ;Lowering the ram: the ram is lowered when 0 The safety screen was open before the cycle began and is now closed (limit switches S4 and S5 actuated) The press is in the home, i.e. upper position (limit switch .S6 actuated) Two-hand switches S1 and S2 were not actuated prior to .the cycle but are now Halting the ram during lowering: the ram stops ;immediately when One of the two-hand switches is released. Or The safety screen is opened. Or .The ram is down (limit switch S3 actuated) Raising the ram: If the ram is down (limit switch S3 风 actuated), it is raised by the eccentric drive. The safety .screen can be opened and both two-hand switches released The machining cycle is completed when the ram reaches the .home position (limit switch S6 actuated) The designer needs for ****** state boxes for drawing the ASM-chart for the controller of the aforementioned system 6 7 9 10 8 5arrow_forward
- The designer needs for ...... state boxes for drawing the ASM-chart for the controller of the .aforementioned system 4 O 7 O 9 10 O 8 6 Oarrow_forwardIn PLC operation retrieves the data into an output module Input scan Output scan Program scan None of the abovearrow_forwardThis NFA design should have no more than 5 states.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Systems ArchitectureComputer ScienceISBN:9781305080195Author:Stephen D. BurdPublisher:Cengage Learning
Systems Architecture
Computer Science
ISBN:9781305080195
Author:Stephen D. Burd
Publisher:Cengage Learning