SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
10th Edition
ISBN: 9781260028379
Author: BUDYNAS
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 14, Problem 20P
A 20° spur pinion with 20 teeth and a module of 2.5 mm transmits 120 W to a 36-tooth gear. The pinion speed is 100 rev/min. and the gears are grade 1, 18-mm face width, through- hardened steel at 200 Brinell, uncrowned, manufactured to a No. 6 quality standard, and considered to be of open gearing quality installation. Find the AGMA bending and contact stresses and the corresponding factors of safety for a pinion life of 108 cycles and a reliability of 0.95.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut.
A.Determine the diametral pitch,
B. face width,
C. and tooth numbers if the material is cast iron, class 25
A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4.
Find the (a) normal circular pitch,
(b) normal diametral pitch, (c) axial pitch,
and (d) dynamic load
Please answer part 2,
A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm.
1.The tangential force transmitted (in N) is
(a) 3552
(b) 2611
(c) 1776
(d) 1305
2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5
the minimum allowable stress for the gear material in MPa is,
(a) 242.0
(c) 121.0
(b) 166.5
(d) 74.0
Chapter 14 Solutions
SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
Ch. 14 - A steel spur pinion has a pitch of 6 teeth/in, 22...Ch. 14 - A steel spur pinion has a diametral pitch of 10...Ch. 14 - Prob. 3PCh. 14 - A steel spur pinion has 16 teeth cut on the 20...Ch. 14 - Prob. 5PCh. 14 - A 20 full-depth steel spur pinion has 20 teeth and...Ch. 14 - A 20 full-depth steel spur pinion has a diametral...Ch. 14 - A steel spur pinion is to transmit 20 hp at a...Ch. 14 - A 20 full-depth steel spur pinion with 18 teeth is...Ch. 14 - Prob. 10P
Ch. 14 - A speed reducer has 20 full-depth teeth and...Ch. 14 - Prob. 12PCh. 14 - Prob. 13PCh. 14 - A 20 20-tooth cast-iron spur pinion having a...Ch. 14 - A steel spur pinion and gear have a diametral...Ch. 14 - A milled-teeth steel pinion and gear pair have Sut...Ch. 14 - A 20 full-depth steel spur pinion rotates at 1145...Ch. 14 - A steel spur pinion has a pitch of 6 teeth/in, 17...Ch. 14 - A commercial enclosed gear drive consists of a 20...Ch. 14 - A 20 spur pinion with 20 teeth and a module of 2.5...Ch. 14 - Repeat Prob. 14-19 using helical gears each with a...Ch. 14 - A spur gearset has 17 teeth on the pinion and 51...Ch. 14 - Prob. 23PCh. 14 - Prob. 24PCh. 14 - The speed reducer of Prob. 14-24 is to be used for...Ch. 14 - Prob. 26PCh. 14 - Prob. 27PCh. 14 - The gearset of Prob. 14-27 is going to be upgraded...Ch. 14 - Prob. 29PCh. 14 - AGMA procedures with cast-iron gear pairs differ...Ch. 14 - Spur-gear teeth have rolling and slipping contact...Ch. 14 - In Ex. 14-5 use nitrided grade 1 steel (4140)...Ch. 14 - In Ex. 14-5 use carburized and case-hardened gears...Ch. 14 - Prob. 35PCh. 14 - Prob. 36PCh. 14 - The countershaft in Prob. 373, p. 152, is part of...Ch. 14 - Build on the results of Prob. 1340, p. 720, to...Ch. 14 - Build on the results of Prob. 1341, p. 721, to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.arrow_forwardA 17-tooth 20° pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth disk gear. The diametral pitch is 10 teeth/in, the face width 1.5 in, and the quality standard is No. 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion is a grade 1 steel with a hardness of 240 Brinell tooth surface and through-hardened core. The gear is steel, through-hardened also, grade 1 material, with a Brinell hardness of 200, tooth surface and core. Poisson's ratio is 0.30, Jp = 0.30, JG = 0.40, and Young's modulus is 30(10°) psi. The loading is smooth because of motor and load. Assume a pinion life of 108 cycles and a reliability of 0.90, and use YN = 1.3558N-0.0178, ZN = 1.4488N-0.023. The tooth profile is uncrowned. This is a commercial enclosed gear unit. (a) Find the factor of safety of the gears in bending. (b) Find the factor of safety of the gears in wear. (c) By examining the factors of safety, identify the threat to each gear and to the…arrow_forwardA pair of 20 degree full depth spur gears have module of 2.5 and to be mounted on shafts with center distance of 90mm and gear ratio of 3. Find : $ if there is an interference $length of action and contact ratio $ if centher ditance was increased by 3mm, find backlash producedarrow_forward
- Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4arrow_forwardA 20◦ helical gear has tangential force of 200lb and helix angle of 16◦ and face width of 0.6”.If the machining error is 0.6 and pitchline velocity is 400ft/min. Determine radial force, axial force, normal force, normal pressure angle and dynamic load.arrow_forwardA 21-tooth pinion rotating at 1000 rpmrpm meshes with a 33-tooth gear in a spur-gear reducer. Both pinion and gear are manufactured to a quality level of 9. A reliability of 0.9 has been specified and the transmitted tangential load is 2500 lblb. Conditions are such that Cm= 1.7. It is proposed that standard 25∘∘, full-depth teeth be used, with both pinion and gear hobbed from an AISI 4140 nitrided steel. The diametral pitch is 6, and the face width 2.000 inin. Suppose that the life of the pinion will be less than that of the gear, the lubricant bulk temperature does not exceed 250∘F∘F, both driver and driven devices are smooth-running, the gearset is external, gears made by conventional methods. Use the average value for the uncorrected surface-fatigue strength when choosing it from the appropriate table. Assume that the reducer is used for critical service applications. a)What is the dynamic factor (Cv) for the pinion? b)What is the AGMA Surface-Geometry Factor(I) for the pinion/gear…arrow_forward
- A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.arrow_forwardProvide very clear and complete solution and diagam. SITUATIONAL PROBLEM: Two shafts are connected by spur gears. The pitch radii of the gears A and B are 200 mm and 860 mm respectively. If shaft A makes 350rpm and is subjected to twisting moment of 250 N-m. Pressure angle is 14.5 degree. What is: a.) Rpm of gear B b.) Torque in shaft B (in Newton meter). c.) Separation load of two gears (in newtons). d.) Total load on gears (in newtons).arrow_forwardIn a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.arrow_forward
- A Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.arrow_forwardA simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The magnitude of the velocity of slip of gears in mesh.arrow_forwardA 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20°pressure angle and a diametral pitch of 32. Determine the base pitch and the contact ratio.Also,calculate the addendum, dedendum, circular pitch, tooth thickness, and the base diameterfor the pinion and gear. If the center distance is increased by 0.125 in., what are the newvaluesfor the contact ratio and the pressure angle.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License