SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
10th Edition
ISBN: 9781260028379
Author: BUDYNAS
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 14, Problem 15P
A steel spur pinion and gear have a diametral pitch of 12 teeth/in, milled teeth, 17 and 30 teeth, respectively, a 20° pressure angle, a face width of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A pair of gears with 20° full-depth teeth are to transmit 15hp at 1750 rpm of the 4-in pinion; velocity ratio desired is about mw= 4; intermittent service. Use a strength reduction factor of about 1.4, with the load at the tip and teeth carefullycut.
A.Determine the diametral pitch,
B. face width,
C. and tooth numbers if the material is cast iron, class 25
A 20◦ helical gear has tangential force of 200lb and helix angle of 16◦ and face width of 0.6”.If the machining error is 0.6 and pitchline velocity is 400ft/min. Determine radial force, axial force, normal force, normal pressure angle and dynamic load.
A helical cast steel gear with 30o helix angle has to transmit 35 kW at 2000 rpm. If the gears has 25 teeth, find the necessary module, pitch diameters and face width for 20o full depth involute teeth. The static stress for cast steel may be taken as 100 MPa. The face width may be taken as 3 times to normal pitch. The tooth form factor is given by the expression y'= 0.154-0.912/TE, where TE represents the equivalent number of teeth. the velocity factor is given by Cv=6/(6+v), where v is the peripheral speed of the gear in m/s.
Chapter 14 Solutions
SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
Ch. 14 - A steel spur pinion has a pitch of 6 teeth/in, 22...Ch. 14 - A steel spur pinion has a diametral pitch of 10...Ch. 14 - Prob. 3PCh. 14 - A steel spur pinion has 16 teeth cut on the 20...Ch. 14 - Prob. 5PCh. 14 - A 20 full-depth steel spur pinion has 20 teeth and...Ch. 14 - A 20 full-depth steel spur pinion has a diametral...Ch. 14 - A steel spur pinion is to transmit 20 hp at a...Ch. 14 - A 20 full-depth steel spur pinion with 18 teeth is...Ch. 14 - Prob. 10P
Ch. 14 - A speed reducer has 20 full-depth teeth and...Ch. 14 - Prob. 12PCh. 14 - Prob. 13PCh. 14 - A 20 20-tooth cast-iron spur pinion having a...Ch. 14 - A steel spur pinion and gear have a diametral...Ch. 14 - A milled-teeth steel pinion and gear pair have Sut...Ch. 14 - A 20 full-depth steel spur pinion rotates at 1145...Ch. 14 - A steel spur pinion has a pitch of 6 teeth/in, 17...Ch. 14 - A commercial enclosed gear drive consists of a 20...Ch. 14 - A 20 spur pinion with 20 teeth and a module of 2.5...Ch. 14 - Repeat Prob. 14-19 using helical gears each with a...Ch. 14 - A spur gearset has 17 teeth on the pinion and 51...Ch. 14 - Prob. 23PCh. 14 - Prob. 24PCh. 14 - The speed reducer of Prob. 14-24 is to be used for...Ch. 14 - Prob. 26PCh. 14 - Prob. 27PCh. 14 - The gearset of Prob. 14-27 is going to be upgraded...Ch. 14 - Prob. 29PCh. 14 - AGMA procedures with cast-iron gear pairs differ...Ch. 14 - Spur-gear teeth have rolling and slipping contact...Ch. 14 - In Ex. 14-5 use nitrided grade 1 steel (4140)...Ch. 14 - In Ex. 14-5 use carburized and case-hardened gears...Ch. 14 - Prob. 35PCh. 14 - Prob. 36PCh. 14 - The countershaft in Prob. 373, p. 152, is part of...Ch. 14 - Build on the results of Prob. 1340, p. 720, to...Ch. 14 - Build on the results of Prob. 1341, p. 721, to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Please answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0arrow_forwardA 57-tooth spur gear is in mesh with a 23-tooth pinion. The gearset transmits 125 hp at 1000 pinion rpm. Size the spur gears for a bending failure safety factor of at least 2 assuming a steady torque, 25∘ pressure angle, full-depth teeth, Qν = 9, an AISI 4140 steel pinion, and a class 40 cast iron gear. Part A Find the appropriate standard diametral pitch for the gearset. Part B Find the minimum required face width of the gears needed to satisfy the safety requirementsarrow_forwardA parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.arrow_forward
- A 17-tooth 20° pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth disk gear. The diametral pitch is 10 teeth/in, the face width 1.5 in, and the quality standard is No. 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion is a grade 1 steel with a hardness of 240 Brinell tooth surface and through-hardened core. The gear is steel, through-hardened also, grade 1 material, with a Brinell hardness of 200, tooth surface and core. Poisson's ratio is 0.30, Jp = 0.30, JG = 0.40, and Young's modulus is 30(10°) psi. The loading is smooth because of motor and load. Assume a pinion life of 108 cycles and a reliability of 0.90, and use YN = 1.3558N-0.0178, ZN = 1.4488N-0.023. The tooth profile is uncrowned. This is a commercial enclosed gear unit. (a) Find the factor of safety of the gears in bending. (b) Find the factor of safety of the gears in wear. (c) By examining the factors of safety, identify the threat to each gear and to the…arrow_forwardA Coniflex, straight-tooth bevel gearset is supported on shafts with centerlines intersecting at a 90° angle. The gear is straddle mounted between closely positioned bearings, and the pinion overhangs its support bearing. The 15-tooth pinion rotates at 900 rpm, driving the 60-tooth gear, which has a di- ametral pitch of 6, pressure angle of 20°, and face width of 1.25 inches. The material for both gears is through-hardened Grade I steel with a hardness of BHN 300 (see Figure). It is desired to have a reliability of 90 percent, a design life of 10° cy- cles, and a governing safety factor of 2.5. Estimate the maximum horsepower that can be transmitted by this gear re- ducer while meeting all of the design specifications given.arrow_forwardAn 54 tooth spur gear transmits a torque of 15000N.mm. The pitch circle diameter is 150 mm, and the pressure angle is 20o. What is most likely the radial force on the gear? 73 N 42 N 31 N 64 Narrow_forward
- A Design of Single Reduction Spur Gearbox An input shaft connected to the motor rotates at 1200 rpm, while the output speed must be 570 rpm. The contact force between the gears is transmitted through the pressure angle of 20°. The radial force is 321,90 kN. The material for both gear and pinion is 817M40. 1.1) select the suitable gear and pinion (make use of the Lewis formula). Then, do one set of calculations for single reduction gearboxarrow_forwardProvide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4arrow_forwardIn a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.arrow_forward
- A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic loadarrow_forwardA 35 kW motor running at 1200 rpm drives a compressor at 780 rpm. The arrangement is made through a 90° bevel gearing arrangement. The pressure angle of teeth is 14.5°. The allowable static stress for both pinion and gear are 85 MPa. Determine the number of teeth on the gear, face width, addendum, dedendum, outside diameter and slant height, thickness of tooth. Also check your design from the standpoint of wear. Take surface endurance limit as 690 MPa and modulus of elasticity as 89 kN/mm2.arrow_forwardAn input shaft connected to the motor rotates at 1200 rpm, while the output speed must be 570 rpm. The contact force between the gears is transmitted through the pressure angle of 20°. The radial force is 321,90 kN. The material for both gear and pinion is 817M40. 1.1 Select the suitable gear and pinion (make use of the Lewis formula). Then, do one set of calculations and tabulate the answers.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License