SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
10th Edition
ISBN: 9781260163155
Author: BUDYNAS
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 17, Problem 10P
Two shafts 20 ft apart, with axes in the same horizontal plane, are to be connected with a flat belt in which the driving pulley, powered by a six-pole squirrel-cage induction motor with a 100 brake hp rating at 1140 rev/min. drives the second shaft at half its angular speed. The driven shaft drives light-shock machinery loads. Select a flat bell.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 15 kW and 1200 r.p.m. motor drives a compressor at 300
r.p.m. through a pair of spur gears having
20° stub teeth. The centre to centre distance between the shafts
is 400 mm. The motor pinion is made
of forged steel having an allowable static stress as 210 MPa,
while the gear is made of cast steel
having allowable static stress as 140 MPa. Assuming that the
drive operates 8 to 10 hours per day
under light shock conditions, find from the standpoint of
strength,
1. Module; 2. Face width and 3. Number of teeth and pitch circle
diameter of each gear.
Check the gears thus designed from the consideration of wear.
The surface endurance limit may be
taken as 700 MPa
A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MP
A conical clutch has an included angle of 105°. The outer and inner diameters are 110mm and 40 mm, respectively, and the coefficient of friction is 0·35. Given the axialforce is 1200 N, determine the torque and power that can be transmitted at 600 rev/min,by each of the two theories:(a) The uniform pressure theory. 8(b) The uniform wear theory
Chapter 17 Solutions
SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
Ch. 17 - Example 17-2 resulted in selection of a 10-in-wide...Ch. 17 - A 6-in-widc polyamide F-l flat belt is used to...Ch. 17 - Prob. 3PCh. 17 - A flat-belt drive is to consist of two...Ch. 17 - In solving problems and examining examples, you...Ch. 17 - Return to Ex. 17-1 and complete the following. (a)...Ch. 17 - Prob. 7PCh. 17 - Prob. 8PCh. 17 - Prob. 9PCh. 17 - Two shafts 20 ft apart, with axes in the same...
Ch. 17 - Prob. 11PCh. 17 - Prob. 12PCh. 17 - A designer has to select a metal-belt drive to...Ch. 17 - Prob. 14PCh. 17 - Prob. 15PCh. 17 - Prob. 16PCh. 17 - Prob. 17PCh. 17 - Two B85 V belts are used in a drive composed of a...Ch. 17 - Prob. 19PCh. 17 - Prob. 20PCh. 17 - The geometric implications of a V-flat drive are...Ch. 17 - A 2-hp electric motor running at 1720 rev/min is...Ch. 17 - The standard roller-chain number indicates the...Ch. 17 - Prob. 24PCh. 17 - A double-strand no. 60 roller chain is used to...Ch. 17 - A four-strand no. 40 roller chain transmits power...Ch. 17 - Prob. 27PCh. 17 - Prob. 28PCh. 17 - Prob. 29PCh. 17 - Prob. 30PCh. 17 - Prob. 31PCh. 17 - Prob. 32PCh. 17 - Prob. 33PCh. 17 - For Prob. 17-29 estimate the elongation of the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An engine of a motor vehicle with a wheel diameter of 712 mm develops 50 kW at 2,000 rpm combined efficiencyof the differential and transmission is 75% with an over-all speed reduction to. 1 determine he torque to bedelivered by the clutch N-m.arrow_forwardTwo pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.arrow_forwardA truck equipped with a 50 HP engine uses a roller chain as the final drive to the rear axle. The driving sprocket runs at 225 rpm with a center distance of approximately 500 fpm. The transmission efficiency between the engine and the driving sprocket is 85%. 1.1 Determine the pitch and width of chain to be used. 1.2 Determine the number of teeth in each sprocket and the pitch diameters.arrow_forward
- The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psiarrow_forwardA pair of helical gears transmit 15 KW power and the pinion is rotating at 1000 rpm. The helix angle is 0.50 radians and the normal pressure angle is 0.35 radians. The pitch diameter of the pinion is 70 mm and the pitch diameter of the gear is 210 mm. Determine the tangential, radial, and axial forces between the gear teeth.arrow_forwardA conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.arrow_forward
- A certain farm equipment which requires 2200 N-m torque at 708 rpm has a diesel engine that operates at 1601 rpm as its prime mover. A No. 60 roller chain with a total length of 60 pitches and a small sprocket with 23 teeth are to be used with an operating temperature to remain constant at 45 degree C. Determine (a) the no. of teeth of the larger sprocket, (b) the pitch diameter of the smaller sprocket in mm, and (c) the pitch diameter of the larger sprocket in mm. Express your answer in 3 decimal places.arrow_forwardA 5 hp motor with a speed of 900 rpm is used to drive an industrial fan with a velocity of 5.72m/s. The center distance between the sprockets is 1.5 times the diameter of driven sprocket andis equal to 630 mm. Determine the length of chain in pitches. Use RC 40 chain and service factorof 1.3.arrow_forwardThe torque of a steel shaft transmitting 20 kW at 320 rpm isarrow_forward
- In the rigid rotor and elastic rotor models, indicate the differences between the expressions corresponding to the energy of the first 6 levels of rotation.arrow_forwardA double thread ACME screw driven by a motor at 534 rpm raises the attached load of 1,062 kg at a speed of 10 meters per minute. The screw has a pitch diameter of 36 mm. The coefficient of friction on threads is 0.15. The friction torque on the thrust bearing of the motor is taken as 20% of the total torque input. Determine the motor power required to operate the screw.arrow_forwardA fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 5/16 inches thick and 10 inches wide is used. The diameters of the motor pulley and the driven pulley are 14 inches and 54 inches, respectively. The center distance is 54 inches and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress of the belt is 350 psi and the belt weighs 0.035 lb/in^3. What is the horsepower capacity of the belt?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License