SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
10th Edition
ISBN: 9781260163155
Author: BUDYNAS
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 17, Problem 23P
The standard roller-chain number indicates the chain pitch in inches, construction proportions, series, and number of strands as follows:
This convention makes the pitch directly readable from the chain number. In Ex. 17-5 ascertain the pitch from the selected chain number and confirm from Table 17-19.
EXAMPLE 17-5 Select drive components for a 2:1 reduction, 90-hp input at 300 rev/min, moderate shock, an abnormally long 18-hour day, poor lubrication, cold temperatures, dirty surroundings, short drive C/p = 25.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 1000 RPM speed reducer and 12KW power drives a conveyor belt at 400 RPM. the distance between the centers is approximately 800mm.
Select a suitable chain for transmission, as follows:1) Solicitation with moderate shock, abnormal operating conditions, operating 24 hours a day.
3) A multiple disc clutch, steel on bronze, is to transmit 7 kW at 1000 rpm. The inner radius of thecontact is 50 mm and outer radius of the contact is 75 mm. The clutch operates in oil with an expected coefficient of "0.1". The average allowable pressure is 0.35 N/mm2. Determine the total number of steel and bronze discs.
See the answer
A flat belt drive system is to be designed for an application in which the input shaft speed (driving pulley) is 1725 rpm, the driven shaft speed is to be approximately 960 rpm, and the power to be transmitted has been estimated as 3.0 horsepower. The driven machine has been evaluated and found to have characteristics of moderate shock loading during operation. The desired center distance between driving and driven pulleys is approximately 18 inches.
Chapter 17 Solutions
SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
Ch. 17 - Example 17-2 resulted in selection of a 10-in-wide...Ch. 17 - A 6-in-widc polyamide F-l flat belt is used to...Ch. 17 - Prob. 3PCh. 17 - A flat-belt drive is to consist of two...Ch. 17 - In solving problems and examining examples, you...Ch. 17 - Return to Ex. 17-1 and complete the following. (a)...Ch. 17 - Prob. 7PCh. 17 - Prob. 8PCh. 17 - Prob. 9PCh. 17 - Two shafts 20 ft apart, with axes in the same...
Ch. 17 - Prob. 11PCh. 17 - Prob. 12PCh. 17 - A designer has to select a metal-belt drive to...Ch. 17 - Prob. 14PCh. 17 - Prob. 15PCh. 17 - Prob. 16PCh. 17 - Prob. 17PCh. 17 - Two B85 V belts are used in a drive composed of a...Ch. 17 - Prob. 19PCh. 17 - Prob. 20PCh. 17 - The geometric implications of a V-flat drive are...Ch. 17 - A 2-hp electric motor running at 1720 rev/min is...Ch. 17 - The standard roller-chain number indicates the...Ch. 17 - Prob. 24PCh. 17 - A double-strand no. 60 roller chain is used to...Ch. 17 - A four-strand no. 40 roller chain transmits power...Ch. 17 - Prob. 27PCh. 17 - Prob. 28PCh. 17 - Prob. 29PCh. 17 - Prob. 30PCh. 17 - Prob. 31PCh. 17 - Prob. 32PCh. 17 - Prob. 33PCh. 17 - For Prob. 17-29 estimate the elongation of the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Determine the principal dimensions of a cone clutch faced with leather to transmit 55 kW at 1100 r.p.m. from an electric motor to an air compressor. Sketch a sectional front view of the clutch and provide the main dimensions on the sketch. Assume : semi-angle of the cone = 15; μ = 0.2; mean diameter of cone = 6 to 10 d where d is the diameter of shaft; allowable normal pressure for leather and cast iron = 0.075 to 0.1 N/mm2; load factor = 1.75 and mean diameter to face width ratio = 6.arrow_forwardb) Design a self-aligning ball bearing with basic dynamic load rating of 69.5 KN to be used in the automobile industry to carry a thrust load of 1184 N. The expected life of the bearing is 5201 hours at 628 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.7 and radial and axial load factors are 1.4 and 2.2 respectively, the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Radial load acting on the bearing in Narrow_forwardThe turning moment diagram for a multi cylinder engine has been drawn toa scale of 1 mm = 4500 N -m vertically and 1 mm = 2. 4 ͦ horizontally. Theintercepted areas between output torque curve and mean resistance lineabove and below the mean taken in order from one end are 342, 23, 245,303, 115, 232, 227, 164 ??2, when the engine is running at 150 rpm. Ifthe mass of the flywheel is 1000 kg and the total fluctuation of speed doesnot exceed 3% of the mean speed, find the minimum value of the radius ofgyration.arrow_forward
- A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20° Assuming that only one pair of the teeth is in contact the total force (in Newton) exerted by a tooth of the pinion on the tooth on a mating gear is...arrow_forward2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria meningitides. The dimensions for the bioreactor are Dt 12.9 cm, ratio Di/Dt = 1/3 and N = 700 rpm. With the scale up factor of 2.24, determine the impeller tip speed (m/s) for the pilot scale bioreactor based on constant impeller tip speed and constant power consumption per volume. Predict which scale up method might give a higher concentration of P64K, if the demand of dissolved oxygen plays an important role.arrow_forwardThe larger diameter and face of the disk of a multiple disk chutch are 225 mm and 20 mm respectively. The load applied to the spring of the clutch axially is 1500 N. Assuming that there are 8 pairs of friction 0.18 and tuning 800 rpm. Find the power transmitted by the clutch using uniform pressure method. (Ans, 13.67 kW)arrow_forward
- Design a single row deep groove ball bearing with basic dynamic load rating of 25.5 KN to be used in a turbine to carry a radial load of 1607 N. The expected life of the bearing is 5226 hours at 523 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in Narrow_forwardThe turning moment diagram for a multicylinder engine has been drawn to a scale of 1 mm = 4550 N-m vertically and 1 mm = 2.5° horizontally. The intercepted areas between output torque curve and mean resistance line taken in order from one end are 340, -24, 245, -305, 120,-232, 228, -165 mm2, when the engine is running at 180 r.p.m. If the mass of the flywheel is 1100 kg and the total fluctuation of speed does not exceed 4% of the mean speed, find the minimum value of the radius of gyration.arrow_forwardA multiple disc clutch, steel on bronze, is to transmit 7 kW at 1000 rpm. The inner radius of the contact is 50 mm and outer radius of the contact is 75 mm. The clutch operates in oil with an expected coefficient of 0.1. The average allowable pressure is 0.35 N/mm2. Determine the total number of steel and bronze discs.arrow_forward
- You are asked to design a four cylinder four-stroke spark ignition engine for a passenger car, which is required to provide a maximum brake torque of (2.60x10^2) Nm at the rated speed of (7.000x10^3) rpm. To simply the design, the bore (B)/stroke (L) ratio is assumed to be unit, i.e. B=L. Given that the bmep of the engine is assumed to be (7.000x10^2) KPa, find its mean piston speed. The answer should be in the unit of m/s with 3 significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Question 7 options: x10 Answerarrow_forwardA spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°, what is the total force exerted by a tooth of the pinion on the tooth on a mating gear?arrow_forwardQ8 A multi-disk clutch consists of two steel disks with one bronze disk. The inner and outer diameters ofthe contacting surfaces are 200 and 250 mm respectively. The coeffi cient of friction is 0.1 and themaximum pressure between the contacting surfaces is limited to 0.4 N/mm. Assuming uniform weartheory, calculate the required force to engage the clutch and the power transmitting capacity at 720rpm.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License