SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
10th Edition
ISBN: 9781260163155
Author: BUDYNAS
Publisher: MCG CUSTOM
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 17, Problem 15P
To determine
The design of a friction belt drive.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
In an open flat belt drive, a pulley of 800 mm diameter runs at 300 r.p.m. The coefficient of friction between the belt and the pulley is 0.25, the angle of lap is 170° and the maximum tension in the belt is 2000 N. The power transmitted is:
10.5 kW
9.4 kW
8.9 kW
7.6 kW
None of the mentioned
13.1 kW
A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 5/16 inches thick and 10 inches wide is used. The diameters of the motor pulley and the driven pulley are 14 inches and 54 inches, respectively. The center distance is 54 inches and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress of the belt is 350 psi and the belt weighs 0.035 lb/in^3. What is the horsepower capacity of the belt?
A double thread ACME screw driven by a motor at 534 rpm raises the attached load of 1,062 kg at a speed of 10 meters per minute. The screw has a pitch diameter of 36 mm. The coefficient of friction on threads is 0.15. The friction torque on the thrust bearing of the motor is taken as 20% of the total torque input. Determine the motor power required to operate the screw.
Chapter 17 Solutions
SHIGLEY'S MECH.ENGIN....(LOOSE)>CUSTOM<
Ch. 17 - Example 17-2 resulted in selection of a 10-in-wide...Ch. 17 - A 6-in-widc polyamide F-l flat belt is used to...Ch. 17 - Prob. 3PCh. 17 - A flat-belt drive is to consist of two...Ch. 17 - In solving problems and examining examples, you...Ch. 17 - Return to Ex. 17-1 and complete the following. (a)...Ch. 17 - Prob. 7PCh. 17 - Prob. 8PCh. 17 - Prob. 9PCh. 17 - Two shafts 20 ft apart, with axes in the same...
Ch. 17 - Prob. 11PCh. 17 - Prob. 12PCh. 17 - A designer has to select a metal-belt drive to...Ch. 17 - Prob. 14PCh. 17 - Prob. 15PCh. 17 - Prob. 16PCh. 17 - Prob. 17PCh. 17 - Two B85 V belts are used in a drive composed of a...Ch. 17 - Prob. 19PCh. 17 - Prob. 20PCh. 17 - The geometric implications of a V-flat drive are...Ch. 17 - A 2-hp electric motor running at 1720 rev/min is...Ch. 17 - The standard roller-chain number indicates the...Ch. 17 - Prob. 24PCh. 17 - A double-strand no. 60 roller chain is used to...Ch. 17 - A four-strand no. 40 roller chain transmits power...Ch. 17 - Prob. 27PCh. 17 - Prob. 28PCh. 17 - Prob. 29PCh. 17 - Prob. 30PCh. 17 - Prob. 31PCh. 17 - Prob. 32PCh. 17 - Prob. 33PCh. 17 - For Prob. 17-29 estimate the elongation of the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A conical clutch has an included angle of 120°, a coefficient of friction of 0.4, and outer and inner diameters of 85mm and 18mm respectively. Using both the uniform wear theory and the uniform pressure theory, calculate the force required to press the two halves together if it is to transmit 300W at 750rev/min. The uniform wear theory and the uniform pressure theory deliver different values for torque in the same system. Which theory would be preferred in practice for use in calculations involving a friction clutch? Give reasons for your choice.arrow_forwardTwo pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? give proper explaination and dont give handwritten solution.arrow_forwardA shaft is loaded in bending and torsion such that Ma = 62 N · m, Ta = 48 N · m, Mm = 54 N · m, and Tm = 25 N · m. For the shaft, Su = 700 MPa and Sy = 560 MPa, and a fully corrected endurance limit of Se = 210 MPa is assumed. Let Kf = 2.2 and Kfs = 1.8. With a design factor of 2.0 determine the minimum acceptable diameter of the shaft in mm using the DE-Goodman criterion.arrow_forward
- A V-belt drive transmits 20kW from an electric motor running at 1440rpm to the main shaft of a roving machine. The motor and main shaft pulleys have 300 & 600 rpm respectively. The coefficient of friction between belt and pulley is 0.25. The centre distance between the shafts is 1000mm. The top width, thickness, section angle and density of belt and permissible tension on the belt are 22mm, 14mm and 40deg, 0.97gcm-2 and 600N respectively. How many belts are needed? Calculate the length of a belt neededarrow_forwardthe power transmitted by a single plate clutch at a speed of 2000 rpm, if the outer and inner radii of Triction surfaces -are 150 mm and 100 mm respectively. The maximum intensity of pressure at any point of contact surface should-not exceed 0.8 x 105 N/m2. Take both sides of the plate as effective and coefficient of friction = 0.3. Assume uniCalculateform wear.arrow_forwardA connecting rod for an I.C. engine running at 1800 r.p.m. and developing a maximum pressure of 3.15 MPa. The diameter of the piston is 100 mm; mass of the reciprocating parts per cylinder 2.25 kg; length of connecting rod 380 mm; stroke of piston 190 mm and compression ratio 6:1. Take a factor of safety of 6 for the design. Take length to diameter ratio for big end bearing as 1.3 and small end bearing as 2 and the corresponding bearing pressures as 10 MPa and 15 MPa. The density of material of the rod may be taken as 8000 kg/m³ and the allowable stress in the bolts as 60 MPa and in cap as 80 MPa. The rod is to be of I-section for which you can choose your own proportions. Calculate the dimension of I- section of the connecting rod.arrow_forward
- A 5 hp motor with a speed of 900 rpm is used to drive an industrial fan with a velocity of 5.72m/s. The center distance between the sprockets is 1.5 times the diameter of driven sprocket andis equal to 630 mm. Determine the length of chain in pitches. Use RC 40 chain and service factorof 1.3.arrow_forwardThe preliminary design of a large shaft connecting a motor with agenerator requires the use of a hollow shaft with inside and outside diameters4 in. and 6 in., respectively. Taking a safety factor of 2.5 andknowing that the shear resistance is 14 ksi, determine the maximumtorque that can be transmitted by the shaft as designedarrow_forwardTwo pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.arrow_forward
- An industrial fan running at 600 rpm is driven by a 25kW, 960rpm, induction motor using an open belt drive. The pulley is mounted on the motor shaft of 270mm diameter. Center distance between the two shafts is 1.45 meters and coefficient of friction is 0.35. Assume thickness of belt equal to 6.5 mm and an allowable stress of 2.86MPa for belt material. Calculate the following: a) Angle of lap for both pulleys; b) Length of the belt; and c) Width of the belt (disregard standard size).arrow_forwardAn open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the corresponding angles of lap are 160° and 210°. The smaller pulley runs at 200 r.p.m. The coefficient of friction between the belt and pulley is 0.25. It is found that the belt is on the point of slipping when 3 kW is transmitted. To increase the power transmitted two alternatives are suggested, namely (i) increasing the initial tension by 10%, and (ii) increasing the coefficient of friction by 10% by the application of a suitable dressing to the belt. Which of these two methods would be more effective? Find the percentage increase in power possible in each case.arrow_forwardThe torque of a steel shaft transmitting 20 kW at 320 rpm isarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License