AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
6th Edition
ISBN: 9780135257418
Author: Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 19, Problem 4CQ
Which of the following may be a symptom of injector O-ring trouble in a HEUI system?
- a. Water getting in the fuel
- b. The fuel filter element turning black
- c. Fuel pressure over 20,000 PSI
- d. Tailpipe exhaust temperature over 572 degrees F (300 degrees C)
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Which of the following statements about carbondioxide is not true?a. CO2 levels are highest when the air-fuel ratiois slightly leaner than stoichiometric.b. The production of CO2 is directly related tothe amount of fuel consumed; therefore,more fuel-efficient engines produce less CO2c. To reduce CO2 levels in the exhaust, engineers are working hard to decrease fuel consumption to keep CO2low.d. The concern for CO2 emissions is one of theprimary reasons for the delayed use of alternative fuels for automobiles.
What are the major components of a Piston Engine fuel System What are their major functions or roles within the system
Explain the steps involved in disconnecting a fuel line on a vehicle with: Multiport fuel injection (50 - 60 words) Gasoline Direct
Iniection (30 - 40 words)
Chapter 19 Solutions
AUTOMOTIVE TECHNOLOGY-NATEF TASK SHEETS
Ch. 19 - What is the difference between direct injection...Ch. 19 - What are the three phases of diesel ignition?Ch. 19 - Prob. 3RQCh. 19 - What exhaust after-treatment is needed to achieve...Ch. 19 - What are the advantages and disadvantages of SCR?Ch. 19 - How is diesel fuel ignited in a warm diesel...Ch. 19 - Which diesel system supplies high-pressure diesel...Ch. 19 - What fuel system component is used in a vehicle...Ch. 19 - Which of the following may be a symptom of...Ch. 19 - Technician A says that glow plugs are used to help...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While diagnosing the cause for blue smoke from the tailpipe of a gasoline engine; Technician A says that a faulty fuel injection system is a likely cause. Technician B says that it is most likely caused by coolant leaking into the combustion chamber. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardWhile discussing returnless fuel systems: Technician A says that in a returnless fuel system the pressure regulator is mounted on the fuel rail. Technician B says that in this type of fuel system the pump and pressure regulator are combined in one unit. Who is correct? A.Technician A B.Technician B C.Both A and B D.Neither A nor Barrow_forwardExcessive oxygen in the exhaust indicates an improper air/fuel mixture. True Falsearrow_forward
- What is the function of the exhaust valve? Regulate the air-fuel ratio Filter air entering combustion chamber Protect piston from exhaust gases Controls flow of exhaust gases out of the combustion chamberarrow_forwardWhich of the following statements about fuel trim is not true? a. A positive fuel trim value means that the PCM detects a lean mixture and is decreasing the pulse width to add more fuel to the mixture. b. Short-term fuel trim represents changes made immediately in response to HO2S signals. c. Long-term fuel trim represents changes made to set a new base pulse width. d. Long-term fuel trim responds to the trends of the short-term fuel trim.arrow_forwardIf a fuel system loses pressure immediately after the ignition is turned off, the possible problems are all of the following except. a. a leaking injector b. restricted fuel lines c. leaking connectors or hoses d. a faulty pressure regulatorarrow_forward
- While diagnosing a PCV problem: Technician A says that a stuck open PCV valve will cause a richer than normal air-fuel mixture. Technician B says that oil in the air cleaner assembly can be caused by worn piston rings. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardLow fuel pump pressure causes a _____ mixture and excessive pressure causes a _____ mixture.arrow_forwardWhich of the following statements regarding the “Pre-Emission Inspection Check” Of a diesel powered vehicle that is subject to Opacity (Smoke Meter) testing is not true? The governor (if equipped), the exhaust system, and the emissions control devices must all be checked. The exhaust system must be checked for any missing sections which would prevent collection of a valid exhaust sample. Vehicles not meeting requirements cannot be inspected. This is not considered an inspection or rejection and no fee is to be charged. The governor, if originally equipped, must be checked for presence, connection, and operation.arrow_forward
- please specify the option (It is a marine diesel engine question)arrow_forward1) Which one of the following is an undesirable byproduct of combustion in IC engines that is caused due to high temperature conditions? O Unburnt hydrocarbons. O Soot O Carbon monoxide. O Oxides of nitrogen. 2) Which one of the following statements is true about emissions from Sl engines? OA rich fuel-air mixture decreases the tendency for more HC emissions ONOX emissions would be maximum at a slightly rich mixture O NOx emissions decrease as the fuel-air mixture becomes either too rich or too lean. OA lean fuel-air mixture increases the tendency for more CO emissions 3) Which one of the following is correct about HC emission? O t is reflective of complete combustion of fuel. It results due to improper mixing of fuel and air O Unburnt HCs do not contribute to photochemical smog. O It decreases as the fuelair mixture becomes too leanarrow_forwardWhile discussing EFI systems: Technician A says that the PCM provides the proper air-fuel ratio by controlling the fuel pressure. Technician B says that the PCM provides the proper air-fuel ratio by controlling injector pulse width. Who is correct? * 1 point a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY