Concept explainers
A 0.9-kg block B is connected by a cord to a 2.4-kg block A that is suspended as shown from two springs, each with a constant of
Want to see the full answer?
Check out a sample textbook solutionChapter 19 Solutions
Vector Mechanics For Engineers
Additional Engineering Textbook Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Degarmo's Materials And Processes In Manufacturing
EBK FUNDAMENTALS OF THERMODYNAMICS, ENH
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
Vector Mechanics for Engineers: Statics and Dynamics
- A 36-lb motor is bolted to a light horizontal beam that has a static deflection of 0.075 in. due to the weight of the motor. Knowing that the unbalance of the rotor is equivalent to a weight of 0.64 oz located 6.25 in. from the axis of rotation, determine the amplitude of the vibration of the motor at a speed of 900 rpm, assuming (a ) that no damping is present, (b ) that the damping factor c/cc is equal to 0.055.arrow_forwardA slender 10-kg bar AB with a length of l = 0.6 m is connected to two collars of negligible weight. Collar A is attached to a spring with a constant of k = 1.5 kN/m and can slide on a horizontal rod, while collar B can slide freely on a vertical rod. Knowing that the system is in equilibrium when bar AB is vertical and that collar A is given a small displacement and released, determine the period of the resulting vibrations.arrow_forwardA machine of mass 75 kg is mounted on springs and is fitted with a dashpot to damp out vibrations. There are three springs each of stiffness 10 N/mm and it is found that the amplitude of vibration diminishes from 38.4 mm to 6.4 mm in two complete oscillations. Assuming that the damping force varies as the velocity, determine : 1. the resistance of the dash-pot at unit velocity ; 2. the ratio of the frequency of the damped vibration to the frequency of the undamped vibration ; and 3. the periodic time of the damped vibration.arrow_forward
- In the case of the forced vibration of a system, determine the range of values of the damping factor c/cc for which the magnification factor will always decrease as the frequency ratio wf/wn increases.arrow_forwardA spring-mass-damper system has a mass of 80 kg suspended from a spring having stiffness of 1000 N/m and a viscous damper with a damping coefficient of 80 N-s/m. If the mass is subjected to a periodic disturbing force of 50 N at an undamped natural frequency, determine (i) The undamped natural frequency. (ii) The damped natural frequency. (iii) The amplitude of forced vibration of mass. (iv) The phase difference.arrow_forwardA motor of mass M is supported by springs with an equivalent spring constant k The unbalance of its rotor is equivalent to a mass m located at a distance r from the axis of rotation. Show that when the angular velocity of the motor is wf, the amplitude of the motion of the motor is wherearrow_forward
- A sensitive electronic system, of mass 25 kg, is supported by a spring-damper isolator that rests on the floor of a manufacturing plant. The operation of nearby rotating equipment causes the floor to vibrate with an amplitude of 8 mm at a frequency of 35 Hz. The electronic system can only operate effectively if the amplitude of its acceleration is less than 40 m/s2. It is known that the damping ratio of the isolator is 0.1. i. Determine the maximum stiffness of the isolator needed for the transmitted acceleration level to be acceptable and hence facilitate effective operation of the electronic system. Using the calculated stiffness value, also determine the largest deformation of the spring in millimetres when the system is in motion. ii. If the damping ratio is allowed to increase by only increasing the equivalent damping coefficient (c) of the isolator, discuss the effect this change would have on the response of the electronic system when operating in the same environment. In your…arrow_forwardA torsional pendulum has a centroidal mass moment of inertia of 0.3kg.m2 and when given an initial twist and released is found to have a frequency of oscillation of 200 rpm. Knowing that when this pendulum is immersed in oil and when given the same initial condition it is found to have a frequency of oscillation of 180 rpm, determine the damping constant for the oil.arrow_forwardTwo springs of constants K1 and K2 are connected in series to a block A that vibrates in simple harmonic motion with a period of 5 s. When the same two springs are connected in parallel to the same block, the block vibrates with a period of 2 s. Determine the ratio K1/K2 of the two spring constants.arrow_forward
- A body of mass of 50 kg is supported by an elastic structure of stiffness 10 kN/m. The motion of the body is controlled by a dashpot such that the amplitude of vibration decreases to one-tenth of its original value after two complete vibrations. Determine: the damping force at 1 m/s, the damping ratio and the natural frequency of vibration.arrow_forwardA 91-kg machine element supported by four springs, each of constant k = 175 N/m, is subjected to a periodic force of frequency 0.8 Hz and amplitude 89 N. Determine the amplitude of the fluctuating force transmitted to the foundation if (a ) a dashpot with a coefficient of damping c=365 N.s/m is connected to the machine element and to the ground, (b) the dashpot is removed.arrow_forwardA 360-lb motor is supported by springs of total constant 12.5 kips/ft. The unbalance of the rotor is equivalent to a 0.9-oz weight located 7.5 in. from the axis of rotation. Determine the range of speeds of the motor for which the amplitude of the fluctuating force exerted on the foundation is less than 5 lb.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY