Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)
5th Edition
ISBN: 9780134009087
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 26, Problem 2CQ
Two technicians are discussing oil leaks. Technician A says that an oil leak can be found using a fluorescent dye in the oil with a black light to check for leaks. Technician B says clean the engine with a cegreaser when trying to locate oil leaks. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that you may be able to
smell antifreeze from a leaking heater core.
Technician B says that you may be able to
hear a loose belt when the engine is running.
Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Technician A says that the engine oil drain
plug typically needs to be replaced with a
new one at each oil change. Technician B
says that engine oil drain plugs must be
tightened with a torque wrench when they
are installed. Who is correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
A vehicle has had several radiator
replacements, and each time there has been
pinhole leaks in the aluminum. Technician A
states that the engine coolant may need to be
exchanged more often. Technician B states
that the engine grounds should be inspected
closely since this could be the cause. Who is
correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
Chapter 26 Solutions
Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)
Ch. 26 - Describe the visual checks that should be...Ch. 26 - Prob. 2RQCh. 26 - Prob. 3RQCh. 26 - Describe how to perform a compression test and how...Ch. 26 - Describe the cylinder leakage test.Ch. 26 - Describe how a vacuum gauge would indicate if the...Ch. 26 - Describe the test procedure for determining if the...Ch. 26 - Prob. 1CQCh. 26 - Two technicians are discussing oil leaks....Ch. 26 - Which of the following is the least likely to...
Ch. 26 - A good engine should produce how much compression...Ch. 26 - Prob. 5CQCh. 26 - A good reading for a cylinder leakage test would...Ch. 26 - Technician A says that during a power balance...Ch. 26 - Cranking vacuum should be __________. a. 2.5 inch...Ch. 26 - Technician A says that a leaking head gasket can...Ch. 26 - The low oil pressure warning light usually comes...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
For the beam loading of Figure P334, draw the complete shearing force and bending moment diagrams, and determin...
Machine Elements in Mechanical Design (6th Edition) (What's New in Trades & Technology)
A pipe flowing light oil has a manometer attached, as shown in Fig, P1.52. What is the absolute pressure in pip...
Fundamentals Of Thermodynamics
What types of polymers are most commonly blow molded?
DeGarmo's Materials and Processes in Manufacturing
A number of common substances are
Some of these materials exhibit characteristics of both solid and fluid beha...
Fox and McDonald's Introduction to Fluid Mechanics
3.3 It is known that a vertical force of 200 lb is required to remove the nail at C from the board. As the nail...
Vector Mechanics for Engineers: Statics
A biological fluid moves at a flow rate of m=0.02kg/s through a coiled, thin-walled, 5-mm-diameter tube submerg...
Fundamentals of Heat and Mass Transfer
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that when draining the engine oil, the engine should be fully cold for best results. Technician B says that the engine should be running when checking the engine oil level. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that broken engine mounts can cause the fan to hit the shroud. Technician B says that missing or broken air dams can cause an engine to overheat. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that excessive engine oil consumption can be caused by low oil levels. Technician B says that excessive oil consumption can be caused by worn valve guides. Who is correct?arrow_forward
- A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling system pulled into a vacuum when cold. Technician A states that a leak in the surge tank could be the cause. Technician B states that the radiator cap is most likely defective. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardTechnician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician B scrapes off heavy deposits before attempting to clean the unit. Who is correct?arrow_forwardWhile looking at the results of an oil pressure test: Technician A says that higher than normal readings can be caused by using oil that is too thin. Technician B says that higher than normal readings can be expected on a cold engine. Who is correct? Technician A Technician Both A and B Neither A nor Barrow_forward
- the oil pressure light stay on whatever the engine fis running, and the oil pressure has been checked and it meet specifications: Technician A says that a ground in the circuit between the indicator light and the pressure switch could be the cause. Technician B says that an open in the pressure switch could be the cause. Who is correct?arrow_forwardWhich of the following is not an effective way to determine if an engine has an internal coolant leak? Performing a pressure test on the system Visually inspecting the exhaust, coolant, and engine oil Using a dye penetrant and black light Using a combustion leak testerarrow_forwardWhen discussing oil consumption: Technician A says using one-quart of oil every 2,000 miles is acceptable. Technician B says oil consumption may increase depending on driving conditions. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that used engine coolant should be collected and recycled. Technician B says that all oil- based waste materials can be collected in the same container if an approved waste disposal company is hired to rid the shop of the oil. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardCarbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forwardAn engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole, but it doesn't not start when fuel is added to the carburetor throat. Tech a says that the problem may be that the exhaust valve is not closing completely due to carbon buildup. Tech b says it may be due to a defective carburetor mounting gasket. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Extent of Reaction; Author: LearnChemE;https://www.youtube.com/watch?v=__stMf3OLP4;License: Standard Youtube License