Automotive Technology: Principles, Diagnosis, And Service; My Automotive Lab With Pearson Etext -- Access Code Card -- For Automotive Technology; ... For Automotive Technology (5th Edition)
5th Edition
ISBN: 9780134209227
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 26, Problem 7CQ
Technician A says that during a power balance test, the cylinder that causes the biggest RPM drop is the weak cylinder. Technician B says that if one spark plug wire is grounded out and the engine speed does not drop, a weak or dead cylinder is indicated. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A discussion concerning CV joint testing is being held.
Technician A says that a recommended method to check CV joints is to raise the vehícle so that the lower control arms are hanging freely; at this point the engine can be
accelerated while noise checks can be performed.
Technician B says that the vehicle should be road tested so that the CV joints can be checked under load.
Who is correct?
O a. A only
O b. B only
c. Both A and B
d. Neither A nor B
Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?
A vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced.
Technician A says that the left inner CV joint may be the source of the noise.
Technician B says that the left outer CV joint may be causing the noise.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
Chapter 26 Solutions
Automotive Technology: Principles, Diagnosis, And Service; My Automotive Lab With Pearson Etext -- Access Code Card -- For Automotive Technology; ... For Automotive Technology (5th Edition)
Ch. 26 - Describe the visual checks that should be...Ch. 26 - Prob. 2RQCh. 26 - Prob. 3RQCh. 26 - Describe how to perform a compression test and how...Ch. 26 - Describe the cylinder leakage test.Ch. 26 - Describe how a vacuum gauge would indicate if the...Ch. 26 - Describe the test procedure for determining if the...Ch. 26 - Prob. 1CQCh. 26 - Two technicians are discussing oil leaks....Ch. 26 - Which of the following is the least likely to...
Ch. 26 - A good engine should produce how much compression...Ch. 26 - Prob. 5CQCh. 26 - A good reading for a cylinder leakage test would...Ch. 26 - Technician A says that during a power balance...Ch. 26 - Cranking vacuum should be __________. a. 2.5 inch...Ch. 26 - Technician A says that a leaking head gasket can...Ch. 26 - The low oil pressure warning light usually comes...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
A 20-lb force is applied to the control rod AB as shown. Knowing that the length of the rod is 9 in. and that t...
Statics and Mechanics of Materials
Locate the centroid of the area. Prob. 9-17
Engineering Mechanics: Statics
Find the change in length of side AB.
Mechanics of Materials, 7th Edition
What types of polymers are most commonly blow molded?
DeGarmo's Materials and Processes in Manufacturing
17–1C A high-speed aircraft is cruising in still air. How does the temperature of air at the nose of the aircra...
Thermodynamics: An Engineering Approach
19.8 Calculate the allowable tensile load for the connection shown. The plates are ASTM A36 steel and the weld ...
Applied Statics and Strength of Materials (6th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that you may be able to smell antifreeze from a leaking heater core. Technician B says that you may be able to hear a loose belt when the engine is running. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that broken engine mounts can cause the fan to hit the shroud. Technician B says that missing or broken air dams can cause an engine to overheat. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardAn engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole, but it doesn't not start when fuel is added to the carburetor throat. Tech a says that the problem may be that the exhaust valve is not closing completely due to carbon buildup. Tech b says it may be due to a defective carburetor mounting gasket. Who is correct?arrow_forward
- A vehicle has had several radiator replacements, and each time there has been pinhole leaks in the aluminum. Technician A states that the engine coolant may need to be exchanged more often. Technician B states that the engine grounds should be inspected closely since this could be the cause. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardA six-cylinder engine has a 1 5 3 6 2 4 firing order. Technician A says that after cylinder number 1 begins its intake stroke, the crankshaft will have to travel 240° before cylinder number 3 begins its intake stoke. Technician B says that when cylinder number 3 and 4 are at TDC, cylinders number 5 and 2 are at BDC. Who is correct and explain why? Technician A Technician B Both A and B Neither A nor Barrow_forwardTrue or False? The camshaft is always locatedin the engine block.arrow_forward
- While diagnosing the cause of TCC shudder: Technician A checks the fluid pressure sent to the clutch. Technician B says that because the shudder occurs only after the clutch is engaged, the problem is the engine, transmission, or another component of the driveline. Who is correct?arrow_forwardTechnician A says a sticking inboard joint can cause the car to shimmy during acceleration. Technician B says a worn inboard joint can cause a clunking during acceleration and deceleration. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardTechnician A says that if an engine had good results from a compression test, it will have good results from a cylinder leakage test Technician B says that if an engine had good results from a cylinder leakage test, it will have good results from a running compression test Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing the misfire monitor: Technician A says that while detecting type A misfires, the monitor checks cylinder misfiring over a 500-revolution period. Technician B says that while detecting type B misfires, the monitor checks cylinder misfires over a 1,000-revolution period. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardThe knocking is usually occurred at the low engine speed O a. True O b. Falsearrow_forwardTechnician A says that the engine oil drain plug typically needs to be replaced with a new one at each oil change. Technician B says that engine oil drain plugs must be tightened with a torque wrench when they are installed. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License