Degarmo's Materials And Processes In Manufacturing
13th Edition
ISBN: 9781119492825
Author: Black, J. Temple, Kohser, Ronald A., Author.
Publisher: Wiley,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 27, Problem 5P
In cutting a 6-in.-long slot in a piece of AISI 1020 cold-rolled steel that is 1 in. thick, the material is fed to a bandsaw blade with teeth having a pitch of 1.27 mm (20 pitch) at the rate of 0.0001 in. per tooth. Estimate the cutting time for the cut.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy = 1200ksi If the width of cut is 0.30 inand the student set a rake angle of 0and a cutting speed of 200fl / min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy= 1200 ksi. If the width of cut is 0.30 in. and the student set a rake angle of 0° and a cutting speed of 200 ft/ min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?
Assuming that the coefficient of friction is 0.25, calculate the maximum depth of cut forturning a hard aluminium alloy on a 15-kW lathe (with a mechanical efficieny of 80%) at awidth of cut of 6 mm, rake angle of 0˚, and a cutting speed of 90 m/min, shear strength of 150 MPa.
Chapter 27 Solutions
Degarmo's Materials And Processes In Manufacturing
Ch. 27 - Why is sawing one of the most efficient of the...Ch. 27 - Explain why tooth spacing (pitch) is important in...Ch. 27 - What is the tooth gullet used for on a saw blade?Ch. 27 - Explain what is meant by the set of the teeth on a...Ch. 27 - How is tooth set related to saw kerf?Ch. 27 - Why can a bandsaw blade not be hardened throughout...Ch. 27 - What are the advantages of using circular saws?Ch. 27 - Why have bandsawing machines largely replaced...Ch. 27 - Explain how the hole in Figure 27.7 is made on a...Ch. 27 - How would you calculate or estimate Tm for a...
Ch. 27 - What is the disadvantage of using gravity to feed...Ch. 27 - What is unique about the broaching process...Ch. 27 - Can a thick saw blade be used as a broach? Why or...Ch. 27 - Broaching machines are simpler in a basic design...Ch. 27 - Why is broaching particularly well-suited for mass...Ch. 27 - In designing a broach, what would be the first...Ch. 27 - Why is it necessary to relate the design of a...Ch. 27 - What two methods can be utilized to reduce the...Ch. 27 - For a given job, how would a broach having...Ch. 27 - Why are the pitch and radius of the gullet between...Ch. 27 - Why are broaching speeds usually relatively low,...Ch. 27 - What are the advantages of shell-type broach...Ch. 27 - Why are most broaches made from alloy or...Ch. 27 - What are the advantages of TiN-coated broaching...Ch. 27 - For mass-production operations, which process is...Ch. 27 - What is the difference between the roughing teeth...Ch. 27 - The sides of a square, blind hole must be machined...Ch. 27 - The interior, flat surfaces of socket wrenches,...Ch. 27 - Prob. 29RQCh. 27 - What are some ways to improve the efficiency of a...Ch. 27 - To what extent is filing different from sawing?Ch. 27 - Prob. 32RQCh. 27 - Prob. 33RQCh. 27 - Prob. 34RQCh. 27 - A surface 12 in. long is to be machined with a...Ch. 27 - The pitch of the teeth on a simple surface broach...Ch. 27 - Estimate the (approximate maximum) horsepower...Ch. 27 - Estimate the approximate force acting in the...Ch. 27 - In cutting a 6-in.-long slot in a piece of AISI...Ch. 27 - The strength of a pull broach is determined by its...Ch. 27 - Suppose you want to shape a block of metal 7 in....Ch. 27 - Could you have saved any time in Problem 7 by...Ch. 27 - Derive the equation for shaping cutting speed.Ch. 27 - How many strokes per minute would be required to...Ch. 27 - How much time would be required to shape a flat...Ch. 27 - What is the metal removal rate in Problem 11 if...Ch. 27 - Suppose you decide to mill the flat surface...Ch. 27 - A planer has a 10-hp motor, and 75% of the motor...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
8.4 The concrete block shown has wall thicknesses of 40 mm, voids that are, and is
overall. Calculate the momen...
Applied Statics and Strength of Materials (6th Edition)
Consider a horizontal. D=1 -mm-diameter platinum wire suspended in saturated water at atmospheric pressure. The...
Fundamentals of Heat and Mass Transfer
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Assume a physical setup as in Fig. P3.6(a). We now heat the cylinder. What happens to P, T, and v (up, down, or...
Fundamentals Of Thermodynamics
A cylinder having a mass of 250 kg is to be supported by the cord that wraps over the pipe. Determine the small...
INTERNATIONAL EDITION---Engineering Mechanics: Statics, 14th edition (SI unit)
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the ...
Statics and Mechanics of Materials (5th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Orthogonal turning of a mild steel tube with a tool of rake angle 10° is carried out at a feed of 0.14 mm/rev. If the thickness of the chip produced is 0.28 mm, Calculate the values of shear angle and shear strain.arrow_forwardWrite down the steps required to proof the mathematical relation for SHEAR PLANE ANGLE in Orthogonal Cutting Model. i-e. Prove the following relation:arrow_forwardAn orthogonal cutting operation is being carried out under the following conditions: t0=0.38 mm, tc=0.65 mm, width of the cut= 2.5 mm, V=3.5 m/s, rake angle=6°, Fc= 515 N, and Ft=210 N. Calculate the percentage of the total energy that is dissipated in the shear plane.arrow_forward
- Calculate the time required for completing a 5mm deep finishing cut on a 150mm wide, 600mmlong face of a 25mm thick steel block using a face milling cutter of 150mm diameter with 6teeth. The cutting condition are Vc =1.5m/sec and fz = 0.1mm.arrow_forwardIn orthogonal turning of a low carbon steel bar of diameter 150 mm with uncoated carbide tool. the cutting velocity is 90 m/min The feed is 0.24 mm/rev and the depth of cut is 2 mm. The chip thickness obtained is 0.48 mm If the orthogonal rake angle is zero and the principal cutting edge angle is 90° Calculate the shear angle in degree.arrow_forward2 1.46 Explain why the power requirements in cutting depend on the cutting force but not the thrust force.arrow_forward
- Calculate the time required to make a ravage cut, at a feed rate of 0.015in. on a piece of machine steel 18in. long by 2in. in diameter.arrow_forwardA motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate:arrow_forwardA 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.arrow_forward
- A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiece having a feedrate of 0.1 mm/tooth and a depth of cut of 4.0 mm. The cutter of 50 mm diameter has 18 straight teeth and rotates at 135 rpm. The given specific energy for this material is 3.5 W s/mm3 and the slab mill is wider than the workpiece to be machined. Calculate:‧ the material-removal rate;‧ the power and torque required for this operation;‧ the cutting time. (243 mm/min, 77760 mm3/min, 4.5 kW, 52.8 s)arrow_forwardManufacturing Process In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 200m/min, feed = 0.25 mm/rev, and depth of cut =7.5 mm. Determine how much power will the lathe machine draw in performing this operation if its mechanical efficiency = 90 %. Use specific energy value is: U = 2.8 J/mmarrow_forwardIn orthogonal turning of low carbon steel pipe with principal cutting edge angle of 90°, the main cutting force is 1000 N and the feed force is 800 N. The shear angle is 25° and orthogonal rake angle is zero Employing Merchant's theory, what is the ratio of friction force to normal force acting on the cutting tool?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
The Most Common Metal Machining Processes (Metal Machining Video 1); Author: Sofeast Ltd;https://www.youtube.com/watch?v=uxVJ3qtezGw;License: Standard YouTube License, CC-BY
Machining process and Machine Tools; Author: Amar Gandhi;https://www.youtube.com/watch?v=X2mUJ8baaE0;License: Standard Youtube License