EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 28, Problem 43SDP
To determine
Microelectronic devices may be subjected to hostile environments, such as high temperature, humidity, and vibration, as well as physical abuse, such as being dropped onto a hard surface. Describe your thoughts on how you would go about testing these devices for their endurance under these conditions. Are there any industry standards regarding such tests? Explain.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Dive into Microchip's involvement in automotive electronics and safety-critical systems. How are their products used in automotive applications, and what safety standards do they comply with?
Given that the time constant's theoretical value is 150.8s, and the percentage error is 0.5%, what is the time constant's experimental value?
Explain the Efficiencies of Mechanical and Electrical Devices
Chapter 28 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 28 - Define the terms wafer, chip, die, device,...Ch. 28 - Why is silicon the semiconductor most used in...Ch. 28 - What do the abbreviations BJT, MOSFET, VLSI,...Ch. 28 - Prob. 4RQCh. 28 - Prob. 5RQCh. 28 - What are the purposes of prebaking and...Ch. 28 - Define selectivity and isotropy, and their...Ch. 28 - Prob. 8RQCh. 28 - Prob. 9RQCh. 28 - What are the levels of interconnection?
Ch. 28 - Which is cleaner, a Class-10 or a Class-1 clean...Ch. 28 - Prob. 12RQCh. 28 - What is a via? Why is it important?Ch. 28 - Describe how electrical connections are...Ch. 28 - Prob. 15RQCh. 28 - Prob. 16RQCh. 28 - Comment on your observations regarding the...Ch. 28 - Describe how n-type and p-type dopants differ.Ch. 28 - Prob. 19QLPCh. 28 - How is epitaxy different from other techniques...Ch. 28 - Note that, in a horizontal epitaxial reactor...Ch. 28 - The table that follows describes three...Ch. 28 - Prob. 23QLPCh. 28 - What is accelerated life testing? Why is it...Ch. 28 - Explain the difference between a die, a chip, anda...Ch. 28 - A common problem in ion implantation is...Ch. 28 - Examine the hole profiles shown in Fig. P28.27...Ch. 28 - Referring to Fig. 28.24, sketch the shape of the...Ch. 28 - Prob. 29QTPCh. 28 - Prob. 30QTPCh. 28 - Prob. 31QTPCh. 28 - A certain design rule calls for metal lines to be...Ch. 28 - Prob. 33QTPCh. 28 - If a square mask of side length 100 m is placed on...Ch. 28 - Obtain an expression for the width of the trench...Ch. 28 - Prob. 36SDPCh. 28 - Inspect various electronic and computer equipment,...Ch. 28 - Describe your understanding of the important...Ch. 28 - Make a survey of the necessity for clean rooms in...Ch. 28 - Prob. 40SDPCh. 28 - Prob. 41SDPCh. 28 - Estimate the time required to etch a spur gear...Ch. 28 - Prob. 43SDPCh. 28 - Review the specific devices, shown in Fig. V.2....
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Explain how physical quantities related to biomedical equipment are measure.arrow_forwardFor a given 40 cm diameter wafer, and a die that is 1.5 cm x 2 cm, determine the cost of a die. Wafer cost is $5800, wafer yield is 100%, and defects per unit area is 0.09/sq. cm.arrow_forwardAn actuator is a device that produces a motion by converting energy and signals going into the system. The motion it produces can be either rotary or linear. Understanding the different types of actuators is a crucial step in making the best selection for your equipment. How do you select the right actuator? Explain your answer.arrow_forward
- A boron implant at 30 keV is done through a gate oxide that is 15nm thick, into a silicon substrate. LSS tables show a boron implant range in oxide at this energy of 100 nm and a standard deviation of 25 nm. Calculate the fraction of boron implant that is absorbed in the oxide.arrow_forward(3.3) What are some of the common sources of indoor noise pollution, and how can noise levels be assessed and controlled in buildings? Note that this question is asking for two aspects, one is noise assessment and the other one is noise control.arrow_forwardDescribe the principles of comparators and its qualities in field of engineeringarrow_forward
- (b) Define THREE (3) common applications of these type of transducers.arrow_forwardWhy is calibration of instruments important in the engineering field? Why is calibration of instruments important in the engineering field?arrow_forwardWhat is an experiment? Provide examples of experiments.arrow_forward
- How does microchip technology influence the aerospace and automotive industries?arrow_forwardHow would you demonstrate the importance of a controlled instrumentation system in the mechanical engineering industry?arrow_forwardCalculate the uncertainty in the area of a circle whose radius is determined to be r = (14.6 ± 0.5) cm?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY