EBK MANUFACTURING ENGINEERING & TECHNOL
7th Edition
ISBN: 8220100793431
Author: KALPAKJIAN
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Question
Chapter 28, Problem 30QTP
To determine
A chlorine-based polysilicon etching process displays a polysilicon-to-resist selectivity of
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Answer each of the following questions in one to three sentences. (a) What is lithography field? (b) What is misalignment in lithography? (e) What is selectivity in an etching process? (d) What is end-point detection in an etching process?
Write in detail following terminologies according to wafer fabrication processes:
a. Diffusion and Ion Implantation
b. Metallization
c. Etching
A siilicon boule has been processed through grinding to provide a cylinder whose diameter = 281 mm and whose length = 899 mm. Next, it will be sliced into wafers 0.8 mm thick using a cut-off saw with a kerf = 0.5 mm. The wafer thus produced will be used to fabricate as many IC chips as possible for the personal computer market. Each IC has a market value to the company of $108. Each chip is square with 17 mm on a side. The processable area of each wafer is defined by a diameter = 265 mm. Estimate the value of all of the IC chips that could be produced (in $), asssuming an overall yield of 84% good product.
Chapter 28 Solutions
EBK MANUFACTURING ENGINEERING & TECHNOL
Ch. 28 - Define the terms wafer, chip, die, device,...Ch. 28 - Why is silicon the semiconductor most used in...Ch. 28 - What do the abbreviations BJT, MOSFET, VLSI,...Ch. 28 - Prob. 4RQCh. 28 - Prob. 5RQCh. 28 - What are the purposes of prebaking and...Ch. 28 - Define selectivity and isotropy, and their...Ch. 28 - Prob. 8RQCh. 28 - Prob. 9RQCh. 28 - What are the levels of interconnection?
Ch. 28 - Which is cleaner, a Class-10 or a Class-1 clean...Ch. 28 - Prob. 12RQCh. 28 - What is a via? Why is it important?Ch. 28 - Describe how electrical connections are...Ch. 28 - Prob. 15RQCh. 28 - Prob. 16RQCh. 28 - Comment on your observations regarding the...Ch. 28 - Describe how n-type and p-type dopants differ.Ch. 28 - Prob. 19QLPCh. 28 - How is epitaxy different from other techniques...Ch. 28 - Note that, in a horizontal epitaxial reactor...Ch. 28 - The table that follows describes three...Ch. 28 - Prob. 23QLPCh. 28 - What is accelerated life testing? Why is it...Ch. 28 - Explain the difference between a die, a chip, anda...Ch. 28 - A common problem in ion implantation is...Ch. 28 - Examine the hole profiles shown in Fig. P28.27...Ch. 28 - Referring to Fig. 28.24, sketch the shape of the...Ch. 28 - Prob. 29QTPCh. 28 - Prob. 30QTPCh. 28 - Prob. 31QTPCh. 28 - A certain design rule calls for metal lines to be...Ch. 28 - Prob. 33QTPCh. 28 - If a square mask of side length 100 m is placed on...Ch. 28 - Obtain an expression for the width of the trench...Ch. 28 - Prob. 36SDPCh. 28 - Inspect various electronic and computer equipment,...Ch. 28 - Describe your understanding of the important...Ch. 28 - Make a survey of the necessity for clean rooms in...Ch. 28 - Prob. 40SDPCh. 28 - Prob. 41SDPCh. 28 - Estimate the time required to etch a spur gear...Ch. 28 - Prob. 43SDPCh. 28 - Review the specific devices, shown in Fig. V.2....
Knowledge Booster
Similar questions
- Stereolithography is a additive manufacturing process. based foil O powder filament liquidarrow_forwardTwo students decided to print a prototype for a gear. Student A use layer thickness of .1 mm and an infill density of 25%. Student B use a layer thickness of 0.07 mm and an infill density of 45%. Which student will take less time to print the gear? Select one: Stu nt since the ckness of layer is smaller and the infill density is higher. O We can't decide which process takes less time O Student A since the thickness of the layer is larger and the infill density is lower. Student B because thickness is higher than B and the infill density has no effect on the process speed. Student A because thickness is higher than B and the infill density has no effect on the process speed.arrow_forwardA boron implant at 30 keV is done through a gate oxide that is 15nm thick, into a silicon substrate. LSS tables show a boron implant range in oxide at this energy of 100 nm and a standard deviation of 25 nm. Calculate the fraction of boron implant that is absorbed in the oxide.arrow_forward
- 2. In general, the rating displacement of an LVDT is within +1". In applications where displacements of more than 1" are necessary, what do you suggest to solve this problem?arrow_forwardThe diameter of a large rotating journal bearing is 400 mm and the film thickness of all between the shaft and the journal is 20 [/~m]. Calculate the ratio of bearing radius to film thicknessarrow_forward(b) Figure 10 shows the holes dimensional accuracy of ECM, EDM, and EEDM process. Compare the accuracy of all processes as illustrated in Figure 10. Electrolyte Dielectric Electrolyte ЕСМ EDM EEDM Figure 10: Holes drilled by ECM, EDM and EEDMarrow_forward
- The distance between a flying drone carrying a laser scanner and a building (Figure 4) is 300m. The distance can be calculated using equation below, where, ris the distance, c is the speed of light and At is the time taken from the laser scanner and the object. r = 1 .c. At 2 Given the building size and shape as in Figure 4. Scanning resolution for this scanner is 4000 points in 1 m?. Consider c = 3.00x10® m/s. Calculate the time taken to scan all possible surfaces of the building. 20 m 40 m 1/8 circle Radius = 25m Width = 40 m 50 m 25 m 10 m 15 m 20 marrow_forwardANSWER THE FOLLOWING : Name one factor PCB fabricators consider when etching a design. Explain thoroughly (include images if applicable)arrow_forwardtwo cylinders are printed on a 3d printer, with a setting of 40% fill rate. This means that the solid parts of the cylinders at 40% plastic material. Given this, tell me how much plastic material is used to make each of these cylinders. I measured both cylinders in meters and these are the measurements below A) Cylinder 1- Height: 0.042m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006m B) Cylinder 2 Height: 0.022m Radius 2(outer radius): 0.008m Radius 1(inner radius): 0.006marrow_forward
- Can you detailed summarize the benefits and the best application of PCD Diamondarrow_forward5. For the process flow below in the yellow highlighted boxes: (i) Mark off location of mask and resist; Label the process step in (ii). Label the process step in (i). Label the process flow in (iv). LMark-off Expose location of resist Develop : =: and mask (left) Material Material iL Label this process step i. Label this process step Material w. Label this process step Dope, redeposit resist and re-do Materialarrow_forwardb) What is the measurement resolution, in degrees of arc, of an incremental optical angle encoder with 100(N+7) lines? Explain. use h=0arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning