Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 29, Problem 6SA
Why is a plastic or metal restrictor placed in either the end of the vent pipe or in the vapor-vent hose on some vehicles?
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Why is a plastic or metal restrictor placed ineither the end of the vent pipe or in the vaporvent hose on some vehicles?
Industrial pipes
What precautions should be taken when opening a supply valve from a flexible hose connected to a pipe outlet?
Why is it preferable to use pneumatic valves in oil sites?
Chapter 29 Solutions
Automotive Technology
Ch. 29 - List at least five safety precautions that should...Ch. 29 - Describe the operation of the evaporative system...Ch. 29 - Fuel pump is a statement of the volume of the fuel...Ch. 29 - Explain the purpose of the relief valve and...Ch. 29 - What is the first thing that should be...Ch. 29 - Why is a plastic or metal restrictor placed in...Ch. 29 - Low fuel pump pressure causes a mixture and...Ch. 29 - True or False? Fuel pressure typically is at its...Ch. 29 - True or False? On todays vehicles, an electric...Ch. 29 - Most fuel tank filler caps contain a pressure...
Ch. 29 - If fuel pump pressure or volume is less than...Ch. 29 - Which of the following statements about a fuel...Ch. 29 - Low fuel pressure can be caused by all of the...Ch. 29 - If a fuel system loses pressure immediately after...Ch. 29 - Technician A says that excessively high pressure...Ch. 29 - Technician A replaces a damaged steel fuel line...Ch. 29 - While discussing electric fuel pumps: Technician A...Ch. 29 - To relieve fuel pressure on an EFI car: Technician...Ch. 29 - While discussing quick-disconnect fuel line...Ch. 29 - While discussing fuel filters: Technician A says...Ch. 29 - While discussing the various fuel filters used in...Ch. 29 - While discussing fuel tank filler pipes and caps:...Ch. 29 - While discussing electric fuel pumps: Technician A...Ch. 29 - While discussing electric fuel pumps: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why is the shielding gas valve "cracked" before the flow-meter regulator is attached?arrow_forwardWhen condenser tubes become fouled, they may be cleaned by A. using a steel brush. B. using a brass brush. C. using a chisel and hammer. D. running a mixture of sand and water through them.arrow_forwardWhy does the high-pressure gauge on a regulator not always indicate the amount of gas in the cylinder?arrow_forward
- How does an injector-type mixing chamber work?arrow_forwardThe pressure at the manifold for natural gas is typically A. 10 psig. B. 8 in. WC. C. 5.5 psia. D. 3.5 in. WC.arrow_forwardExplain how the oil separator, oil reservoir, pressure differential valve, and oil-level regulators work together tomaintain the correct oil level in parallel compressors.arrow_forward
- What kind of circuit balancing valve is used in the hot and chilled water piping? a. balancing globe valve b. shut-off balancing valve c. pressure balancing valve d. pressure by-pass valvearrow_forwardSurface condensers allow the two fluids to mix, is the statement true or falsearrow_forwardOne way to prevent leaking from glove valves in a Halocarbon refrigeration system is to employ Teflon tape gland followers valve stem packing sealed worm gearsarrow_forward
- Explain why a pressure relief valve is needed in an automotive oil pump.arrow_forwardWhen evacuating a refrigeration system that has solenoid valves, what special procedure must be followed?arrow_forwardWhich of the following statements is not true about orifice tube systems? The suction line must be cool to the touch from the evaporator outlet to the compressor. The liquid line from the condenser outlet to the evaporator inlet should be cool. The evaporator should feel very cold. The accumulator must be cool to the touch.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Physics 33 - Fluid Statics (1 of 10) Pressure in a Fluid; Author: Michel van Biezen;https://www.youtube.com/watch?v=mzjlAla3H1Q;License: Standard YouTube License, CC-BY