Automotive Technology: A Systems Approach - With Manual and Access
6th Edition
ISBN: 9781305513235
Author: ERJAVEC
Publisher: Cengage
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 31, Problem 8RQ
Which of the following would not cause a hard-to-start problem on a PFI engine?
a. A defective IAC valve
b. A defective oxygen sensor
c. A leaking fuel pressure regulator
d. Dirty injectors
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that only offshore engines are permitted to use port-helix metering fuel systems on
EPA MY 2010 compliant and later engines. Technician B says that port-helix metering injection
pumps can be used on current diesel engines when the peak power rating is less than 70 BHP (52 kW).
Who is correct?
an engine is being discussed for lean running condition. technician A checks for air leak in the intake. Technician B checks for alcohol in the fuel. who is correct?
While discussing EFI systems: Technician A says that the PCM provides the proper air-fuel ratio by controlling the fuel pressure. Technician B says that the PCM provides the proper air-fuel ratio by controlling injector pulse width. Who is correct? *
1 point
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Chapter 31 Solutions
Automotive Technology: A Systems Approach - With Manual and Access
Ch. 31 - List four service precautions for working on the...Ch. 31 - What is indicated by a LTFT reading of 24 percent?Ch. 31 - What is the correct procedure for checking an...Ch. 31 - What is the difference between STFT and LTFT?Ch. 31 - The PCM checks for a closed throttle plate each...Ch. 31 - Which of the following is a likely cause of a lean...Ch. 31 - What problem may result from dirt buildup on an...Ch. 31 - Which of the following would not cause a...Ch. 31 - What is the correct way to test an injector with...Ch. 31 - What is the difference between the pulse width and...
Ch. 31 - How can you use a dual trace scope to make sure...Ch. 31 - What are three possible problems that can allow...Ch. 31 - What is the purpose of having two accelerator...Ch. 31 - What is indicated by a negative LTFT value?Ch. 31 - True or False? The signals from an air-fuel ratio...Ch. 31 - While discussing the causes of...Ch. 31 - While discussing IAC valve diagnosis: Technician A...Ch. 31 - While discussing IAC motor removal, service, and...Ch. 31 - While discussing injector testing: Technician A...Ch. 31 - While discussing airflow sensors: Technician A...Ch. 31 - While discussing scan tool diagnosis of fuel...Ch. 31 - While discussing a high idle speed problem:...Ch. 31 - While discussing the causes of a rich air-fuel...Ch. 31 - While diagnosing an idle speed problem: Technician...Ch. 31 - While looking at fuel trim values: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When the engine is idling, the pressure regulator in a PFI system provides ____fuel pressure compared to the fuel pressure at wide-open throttle.arrow_forwardTechnician A says there is less heat energy in high octane gasoline and, therefore less power is genorated during combustion. Technician B says usung a higher octane gasoline than required will not produce more power inless the engine has a knock sensor that allows the system to adjust ignition timing to take advantage of the higher octane. who is correct?arrow_forwardDifferentiate the two types of external combustion enginearrow_forward
- Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says that the flywheel will be harder to spin when starting the engine. Tech b says that the engine will loose power. Who is correct?arrow_forwardWhich of the following is similar to a PCV valve but is specific to diesel engines? PCM EGR AIR CDRarrow_forwardWhile discussing the compression ratios used with engines equipped with a GDI system: Technician A says that higher ratios can be used because ignition timing is normally very advanced. Technician B says that higher ratios are possible because the small droplets of fuel injected directly into the cylinder tend to cool the mixture in the cylinder. Who is correct?a.tech a b.tech b c. Both a and b d. Neither a nor barrow_forward
- When the engine is Idling, the pressure regulator in PFI system provides _____________ fuel pressure compared to the fuel pressure at wild open throttle.arrow_forwardTechnician A says that black exhaust smoke is an indication of a too-rich air-fuel mixture. Technician B says that white smoke (steam) is an indication of coolant being burned in the engine.arrow_forwardA rich air-fuel ratio causes HC emissions to ________.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY