Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 31, Problem 9ASRQ
While diagnosing an idle speed problem: Technician A says that higher-than-normal TP signals at idle will cause the IAC to close, which will decrease idle speed. Technician B says that if the resistance of the ECT is too low, a lower-than-normal voltage signal is sent to the PCM, which interprets this as a hot engine and will close the IAC to decrease speed. Who is correct?
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
While discussing SFI systems: Technician A says that when the injection system fires according to crankshaft position and speed, it is operating in the synchronous mode. Technician B says that one of the advantages of SFI systems is that they are always in the synchronous mode. Who is correct?
While discussing ignition timing control in EI systems: Technician A says that when the engine coolant temperature is low, the timing is retarded until normal operating temperature is reached. Technician B says that the PCM will retard the timing during EGR operation. Who is correct?
Technician Ac.Both A and B
b. Technician B d. Neither A nor B
what is an attenuator used for in vehicle
Chapter 31 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 31 - List four service precautions for working on the...Ch. 31 - What is indicated by a LTFT reading of 24 percent?Ch. 31 - What is the correct procedure for checking an...Ch. 31 - What is the difference between STFT and LTFT?Ch. 31 - The PCM checks for a closed throttle plate each...Ch. 31 - Which of the following is a likely cause of a lean...Ch. 31 - What problem may result from dirt buildup on an...Ch. 31 - Which of the following would not cause a...Ch. 31 - What is the correct way to test an injector with...Ch. 31 - What is the difference between the pulse width and...
Ch. 31 - How can you use a dual trace scope to make sure...Ch. 31 - What are three possible problems that can allow...Ch. 31 - What is the purpose of having two accelerator...Ch. 31 - What is indicated by a negative LTFT value?Ch. 31 - True or False? The signals from an air-fuel ratio...Ch. 31 - While discussing the causes of...Ch. 31 - While discussing IAC valve diagnosis: Technician A...Ch. 31 - While discussing IAC motor removal, service, and...Ch. 31 - While discussing injector testing: Technician A...Ch. 31 - While discussing airflow sensors: Technician A...Ch. 31 - While discussing scan tool diagnosis of fuel...Ch. 31 - While discussing a high idle speed problem:...Ch. 31 - While discussing the causes of a rich air-fuel...Ch. 31 - While diagnosing an idle speed problem: Technician...Ch. 31 - While looking at fuel trim values: Technician A...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Describe how engine misfire is detected in an OBD II system.arrow_forwardDescribe the purpose of CO2 and O2 indicators.arrow_forwardTechnician A says that throttle position is an important input in most electronic shift control systems. Technician B says that vehicle speed is an important input for most electronic shift control systems. Who is correct?arrow_forward
- Briefly explain the operation of the UJT.arrow_forwardExplain the trip and drive cycle in an OBD II system.arrow_forwardTechnician A says that if a drive belt does not have the proper tension, it may produce squealing and chirping noises. Technician B says belt tension should be checked even if the engine has an automatic belt tensioner. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- Explain why a height-sensing proportioning valve is required on some vehicles.arrow_forwardWhile discussing a high idle speed problem: Technician A says that higher-than-normal idle speed may be caused by low electrical system voltage. Technician B says that higher-than-normal idle speed may be caused by a defective coolant temperature sensor. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardWhat is indicated by a LTFT reading of 24 percent?arrow_forward
- While discussing throttle-by-wire systems: Technician A says that a spring on the throttle shaft provides the limp-home feature. Technician B says that most systems have redundant processors and the TP and accelerator pedal sensors send redundant input signals. Who is correct?A. Tech A B. Tech B C. Both A and B D. Neither A nor Barrow_forwardExplain the above : pressure sensor, pressure gauge and pressure transmitter with an applicationarrow_forwardWhich of the following systems is designed to reduce NOX? VVT EVAP PCV AIRarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license