AUTO TECH/TASK SHEET
6th Edition
ISBN: 9780135257630
Author: Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 32, Problem 10CQ
Two technicians are discussing variable valve timing. Technician A says that changing the exhaust valve timing helps reduce exhaust emissions. Technician B says that changing the intake valve timing helps increase low-speed torque. Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Technician A says that you may be able to
smell antifreeze from a leaking heater core.
Technician B says that you may be able to
hear a loose belt when the engine is running.
Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Explain briefly
1. Valve lag
2. intake lag
While discussing the compression ratios used with engines equipped with a GDI system: Technician A says that higher ratios can be used because ignition timing is normally very advanced. Technician B says that higher ratios are possible because the small droplets of fuel injected directly into the cylinder tend to cool the mixture in the cylinder. Who is correct?a.tech a
b.tech b
c. Both a and b
d. Neither a nor b
Chapter 32 Solutions
AUTO TECH/TASK SHEET
Ch. 32 - How is the camshaft driven by the crankshaft?Ch. 32 - What drives the high-pressure fuel pump on a GDI...Ch. 32 - What is meant by an interference engine?Ch. 32 - How does variable valve timing help improve engine...Ch. 32 - The camshaft makes __________ for every revolution...Ch. 32 - A DOHC V-6 has how many camshafts? a. 4 b. 2 c. 3...Ch. 32 - Which timing chain type is also called a silent...Ch. 32 - Many technicians always use new pushrods because...Ch. 32 - Hydraulic valve lifters can make a ticking noise...Ch. 32 - Hydraulic lifters or hydraulic lash adjusters...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
19.8 Calculate the allowable tensile load for the connection shown. The plates are ASTM A36 steel and the weld ...
Applied Statics and Strength of Materials (6th Edition)
A 20-lb force is applied to the control rod AB as shown. Knowing that the length of the rod is 9 in. and that t...
Statics and Mechanics of Materials
Describe the structural changes that take place when a plain-carbon eutectoid steel is slowly cooled from the a...
Foundations of Materials Science and Engineering
A biological fluid moves at a flow rate of m=0.02kg/s through a coiled, thin-walled, 5-mm-diameter tube submerg...
Fundamentals of Heat and Mass Transfer
Determine the length of the cantilevered beam so that the maximum bending stress in the beam is equivalent to t...
Mechanics of Materials (10th Edition)
What types of polymers are most commonly blow molded?
Degarmo's Materials And Processes In Manufacturing
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole, but it doesn't not start when fuel is added to the carburetor throat. Tech a says that the problem may be that the exhaust valve is not closing completely due to carbon buildup. Tech b says it may be due to a defective carburetor mounting gasket. Who is correct?arrow_forwardWhile discussing SFI systems: Technician A says that when the injection system fires according to crankshaft position and speed, it is operating in the synchronous mode. Technician B says that one of the advantages of SFI systems is that they are always in the synchronous mode. Who is correct?arrow_forwardan engine is being discussed for lean running condition. technician A checks for air leak in the intake. Technician B checks for alcohol in the fuel. who is correct?arrow_forward
- The function of carburettor used in engine is to a. mix air, petrol and diesel in engines b. mix petrol and diesel in engines c. mix air and diesel in engines d. mix air and petrol in enginesarrow_forwardExplain why a height-sensing proportioning valve is required on some vehicles.arrow_forwardTechnician A says that if the PCV valve or connecting hoses become clogged, excessive pressure will develop in the crankcase and can cause oil leaks. Technician B says that if the PCV valve or connecting hoses become clogged, oil may be pushed into the air cleaner or cause it to be drawn into the intake manifold. Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forward
- While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?arrow_forwardExplain briefly 1. Valve lead 2. Intake lead 3. Exhaust leadarrow_forwardA vehicle has had several radiator replacements, and each time there has been pinhole leaks in the aluminum. Technician A states that the engine coolant may need to be exchanged more often. Technician B states that the engine grounds should be inspected closely since this could be the cause. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forward
- The gas/oil mixture used in a two stroke engine has been properly mixed. The carburetor high speed & cruise circuit is adjusted to lean. Tech a says that the lean adjustment may cause the engine to fail due to improper lubrication: tech b says that it may cause the engine to fail because of overheating. Who is correct?arrow_forwardA restricted exhaust system can cause______. a. stalling b. loss of power c. backfiring d. all of the abovearrow_forwardTechnician A says an engine may use one or more valve springs per valve. Technician B says additional valve springs are used to control vibration and increase total pressure. Who is correct? a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY